• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.389-396
• /
• 2017

Restorations of automotive parts have been done ever since the first vehicle was produced. Because the most expensive parts of a vehicle are in the engine system, there have been various restoration methods developed for engine parts. In the case of commercial diesel engines, the fuel injection device is a key and expensive component. It also has a significant effect on vehicle performance. In particular, reduced engine power and increased exhaust gas emissions may result from mechanical damage due to abrasion of the spill valve in the fuel injection system of a diesel engine. In this paper, restoration techniques for damaged parts are applied to restore the abrasion of a spill valve of fuel injection, also called as the "unit injector", of commercial diesel engines. In order to recover the damage, optimized polishing techniques using hard-metal and coating processes are applied. To evaluate restoration techniques for the spill valve, performance and durability tests are performed on a test bench.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.169-175
• /
• 2013

CRDi technology of diesel engine was developed from in the early 2000s due to a need to increase fuel efficiency and environment care. Especially, high-pressure fuel injection system in CRDi system which has a fuel injection unit including an injector, a fuel pump and common-rail, etc. becomes possible to make the exhaust gas clean as well as power improvement. In this study, comparison of dynamic characteristics of servo-hydraulic piezo-driven injector with 3-way and bypass-circuit type was analyzed by using the AMESim code. As results of this study, it found the bypass-circuit inside servo-hydraulic piezo injector can cause a faster injection response than that of the 3-way type. Also it was shown that bypass-circuit type had better control capability due to hydraulic bypass system.

• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.146-156
• /
• 2003

A numerical algorithm is developed to analyze the performance of a Unit-injector (UI) System for a diesel engine. The fundamental theory of the algorithm is based on the continuity equation of fluid dynamics. The loss factors that should be seriously regarded on the continuity equation are the compressibility effect of liquid fuel, the wall friction loss in high-pressure fuel lines of the system, the kinetic energy loss of fuel in the system, and the leakage of fuel out of the control volume. For an evaluation of the developed simulation algorithm, the calculation results are compared with the experimental outputs provided by the Technical Research Center of Doowon Precision Industry Co. (DPICO) ； the maximum pressure in the plunger chamber (P$\_$p/) and total amount of fuel injected into a cylinder per cycle (Q$\_$f/) at each operational condition. The result shows that the average error rate (%) of P$\_$p/ and Q$\_$f/ are 2.90% and 4.87%, respectively, in the specified operational conditions. Hence, it can be concluded that the analytical simulation algorithm developed in this study can be reasonably applied to the performance prediction of newly designed UI system.

• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.43-51
• /
• 1998

Most of fuel-injection system operated with mechanical methods are difficult to control the injection quantity and injection timing as well as injection rate exactly. Moreover high pressure injection scheme is never be realized with conventional one. On the other hand, serious air pollution can be lessened with injection system equipped with those functions. Therefore, electronically controlled Unit Injuctor(UI) appeared to satify above mentioned desires. However, it is still difficult that the most important part, especially solenoid valve, is analyzed precisely, because of the existence of complex combination of electromagnetics, electrics and dynamic problems. In this study, experimental and theoretical analysis are accomplished for understanding of solenoid valve characteristics and further its design. As the result, the follows are obtained 1) As the increase of wire diameter, the response time became shorter and optimal inductance existed in relative with the response time and wire diameter. 2) According to increasing input voltage, the traction force increased, otherwise the response time was shortened. 3) As the increase of armature stroke, the traction force decreased and the response time became longer.

• 한국응용과학기술학회지
• /
• 제31권4호
• /
• pp.688-693
• /
• 2014

본 연구는 생활주변에서 오존수를 쉽게 활용할 수 있도록 오존수 발생장치의 활용성을 증가시키고 한 동작으로 작동하는 시스템을 개발하고자 한다. 더 나아가 올리브 오일과 오존과 반응시켜 제조하는 기술에 적용하고자 한다. 기존의 경우 대부분이 오존수 시스템이 아닌 오존발생기 위주의 제품이 많다. 오존수기의 경우 펌프로 강제 흡입시키는 일반압력 방식으로 오존가스 누출 위험요소가 내포 되어 있으나, 본 과제의 경우 인젝터를 이용하여 물의 유입여부에 따른 오존의 발생과 흡입을 제한하고 있어 기존 제품의 오존 누출에 의한 위험을 최소화하였다. 인젝터 방식의 단점에도 불구하고 미생물 살균능을 유지하는 것으로 본 연구에서 사용된 인젝터 방식 오존수 제조 장치의 효용성을 알 수 있었다.

• 청정기술
• /
• 제30권2호
• /
• pp.94-104
• /
• 2024

재제조는 사용 후 제품을 분해, 세척, 검사, 보수, 조정, 재조립하여 원래의 성능 또는 그 이상의 성능을 가진 제품으로 재상품화하는 것으로, 재제조산업은 2050 탄소중립을 실현하기 위해 필요한 핵심 산업이다. 본 연구에서는 자동차부품 중 재제조가 활발히 이루어지고 있는 인젝터를 대상으로 전과정평가를 이용하여 회피효과를 고려 시와 미고려 시 자원 저감 및 온실가스 저감 효과를 분석하고자 한다. 연구결과, 인젝터 재제조로 인한 자원 저감 효과와 온실가스 저감 효과는 회피효과를 미고려 시 1개 기준으로 95.30%, 93.88%가 저감되는 것으로 나타났다. 재제조 시 제품을 재사용함으로써 사용 후 제품이 폐기되지 않는 환경영향과 천연자원을 사용하지 않는 환경영향의 회피효과를 고려할 시 190.91%, 188.33%가 저감되는 것으로 나타났다. 본 연구결과는 향후 재제조 시 회피효과를 고려한 환경영향 저감량을 평가하고, 연구방법론 개발 시 활용할 수 있을 것으로 본다.

• 오토저널
• /
• 제14권6호
• /
• pp.67-73
• /
• 1992

This paper describes Hyundai's research and development work on a flexible fuel vehicle (FFV). The work on FFV has been conducted to evaluate its potential as an alternative to the conventional gasoline vehicle. Hyundai FFV described here can be operated on M85, gasoline, or any of their combinations, in which the methanol concentration is measured by an electrostatic type fuel sensor. For that operation, a special FFV ECU(Eletronic Control Unit) has been developed and incorporated in the FFV. The characteristics affecting FFV operation, such as FFV ECU control strategy and injector flow rate, have been investigated and optimized through the experiment. And various development tests have been performed in view of engine performance, durability, cold startability, and exhaust emissions reduction. The exhaust gas aftertreatment system consisting of manifold type catalyst and secondary air injection system shows good emission reduction performance including formaldehyde, and finally, the possibility of the FFVs as the low emission vehicles is evaluated by presenting NMOG(Non-Methane Organic Gases) levels with respect to M0 and M85. With these results, it is concluded that FFV can be a candidate for the low emission vehicles, but more works on its durability improvement is required.

• 한국가스학회지
• /
• 제17권3호
• /
• pp.8-13
• /
• 2013

이 논문의 목적은 LPG 자동차에서 연료누설에 의한 화재관련 사례에 대하여 연구하는 것이다. 첫 번째 사례는, 엔진의 연료 레귤레이터 및 인젝터 사이의 고압호스와 연결되는 연료 라인을 수리한 다음 고정하는 볼트를 규정토크로 조이지 않아 호스가 빠지면서 LP 가스가 누출되어 엔진의 열에 의해 화재가 발생한 것을 확인하였다. 두 번째 사례는, 인젝터를 교환한 다음 흡기매니폴드 유닛의 조립부에 삽입할 때 고정하는 고정부를 점검하지 않고 고정부가 변형되어 휜 상태에서 조립한 결과 연료의 누설을 방지하는 O링이 찢어져 이 사이로 연료가 누출된 것으로 확인되었다. 세 번째 사례는, 연료압력 조절기 유닛에는 연료 차단 솔레노이드 밸브가 연결되어 있는데 수리 후 이 연결 커넥터의 기밀작업을 철저하게 하지 않아서 미세하게 LP 가스가 누설되다가 어느 순간에 많은 양의 가스가 누설되면서 엔진의 열에 의해 화재가 발생된 것을 확인하였다. 따라서, 연료 시스템에 문제가 없는지 철저하게 관리하여 화재의 발생이 최소가 되도록 하여야 한다.

• 항공우주기술
• /
• 제11권2호
• /
• pp.57-64
• /
• 2012

보조동력장치 개발에서 성공적인 연소기 개발이 이루어졌다고 하더라도 엔진에 조립되어 실제 환경에서 운용될 경우, 예상하지 못한 문제나 현상들이 발생하는 사례가 많이 있다. 하지만, 엔진 또는 체계단위의 개발단계에서는 연소기의 유동장이나 하드웨어의 구조적 변경은 불가능하거나 아주 작은 범위 내에서 가능하다. 따라서 체계 운용 중 발생한 문제에 대하여 시험과 유동해석을 통해 원인 규명 및 해결 방안을 제시하고, 이를 반복시험을 통해 확인, 검증하여야 한다. 본 논문에서는 엔진 및 체계 시험과정 동안 발생한 환형 역류형 연소기 관련 문제들을 유동해석과 엔진시험을 통해 해결, 검증한 과정에 대하여 기술하였다.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.76-83
• /
• 2010

Recently, as the current and future emission regulations go stringent, the research of NOx reduction has become a subject of increasing interest and attention in diesel engine. Selective Catalytic Reduction (SCR) is one of the effective technology to reduce NOx emission from diesel engine. Especially, Urea-SCR that uses urea as a reductant is becoming increasingly popular as a cost effective way of reducing NOx emissions from heavy duty vehicles. In this research, we designed urea injector and DCU (Dosing Control Unit) specially developed for controlling the Urea-SCR process onboard vehicles. As passenger and commercial diesel engine experiment, we grasped characteristics of NOx emission and SCR catalyst temperature level in advance. As a result, highest NOx emission level was shown in condition of low engine speed and high load. On the other hand, SCR catalyst temperature was highest at high engine speed and load. On the basis of these result, we conducted the NOx reduction test at steady engine operating conditions using the urea injector and DCU. It was shown that 74% NOx conversion efficiency on the average and 97% NOx conversion efficiency was obtained at high SCR catalyst temperature.