• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.232-236
• /
• 2004

The fracture characteristics of unidirectional composite single-lap bonded joints were investigated experimentally and numerically. The effects of bonding method, surface roughness, bondline thickness and the existence of fillet on the failure characteristics and strength of bonded single-lap joints were evaluated experimentally. The failure process, failure mode and the behavior of load-displacement curve was apparently different according to bonding method. The failure load of the specimen co-cured without adhesive was definitely superior to other types of specimens but the specimens co-cured with adhesive film had a less strength than secondary bonded specimens. In the secondary bonded specimens, the lower value of surface roughness and existence of fillet improved the strength of specimens. The strain energy release rates calculated by geometric nonlinear finite element analyses and Virtual Crack Closure Technique for the secondary bonded specimens considering the three types of initial cracks - comer crack, edge crack and delamination crack - were consistent with the test results.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.410-414
• /
• 2004

Under longitudinal loading continuous fiber reinforced metal matrix composite(MMC) have interpreted an outstanding performance. However, the applicability of continuous fiber reinforced MMCs is somewhat limited due to their relatively poor transverse properties. Therefore, the transverse properties of MMCs are significantly influenced by the properties of the fiber/matrix interface. In this study, elastic-plastic behavior of transversely loaded unidirectional fiber reinforced metal matrix composites investigated by using elastic-plastic finite element analysis. Different fiber placement(square and hexagon) and fiber volume fractions were studied numerically. The interface was treated as three thin layer (with different properties) with a finite thickness between the fiber and the matrix. The analyses were based on a two-dimensional generalized plane strain model of a cross-section of an unidirectional composite by the ANSYS finite element analysis code.

• Journal of Magnetics
• /
• v.7 no.1
• /
• pp.9-13
• /
• 2002

The dependences of microscopic magnetic domain on film thickness in unidirectional and isotropic exchange-coupled NiO/NiFe bilayers were investigated by magnetic force microscopy to better understand for exchange biasing. As NiO thickness increases, microscopic domain structure of unidirectional biased film changed to smaller and more complicated domains. However, for isotropic-coupled film a new cross type domain appeared with out-of plane magnetization orientation. The density of the cross domain is proportional to exchange biasing fields and the fact that the domain was originated by the strongest exchange coupling region was confirmed from the dynamic domain configuration during a magnetization cycle.

• Korean Journal of Optics and Photonics
• /
• v.10 no.3
• /
• pp.233-236
• /
• 1999

We have constructed a narrow-linewidth single-longitudinal-mode unidirectional $Er^{3+}$ -doped fiber laser using a fiber Bragg grating incorporated by a three port optical circulator with a compact configuration. Using a conventional delayed self-heterodyne detection technique with Mach-Zehnder interferometer a linewidth of 5 kHz was measured. In a single-longitudinal-mode operation, output power of up to 2.7 mW at 1548 nm were obtained for a launched pump power of 43 mW at 980 nm.

• IE interfaces
• /
• v.13 no.4
• /
• pp.556-563
• /
• 2000

In this paper, we consider wavelength assignment problem (WAP) in Wavelength division multiplexed (WDM) unidirectional optical telecommunication ring networks. We show that, even though WAP on unidirectional ring belongs to NP-hard, WAP can be exactly solvable in real-sized WDM rings for near future demand. To accomplish this, we convert WAP to the vertex coloring problem of the related graph and choose a special integer programming formulation for the vertex coloring problem. We use a column generation technique in a branch-and-price framework for the suggested formulation. We also propose some generic heuristics and do the performance comparison with the suggested optimization algorithm.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.287-288
• /
• 2006

Two approaches for the fabrication of tailored powder composites with specially distributed pore-grain structure and chemical composition are investigated. Electrophoretic Deposition (EPD) followed by microwave sintering is employed to obtain functionally graded materials (FGM) by in-situ controlling the deposition bath suspension composition. $Al_2O_3/ZrO_2$ and zeolite FGM are successfully synthesized using this technique. In order to fabricate an aligned porous structure, unidirectional freezing followed by freeze drying and sintering is employed. By controlling the temperature gradient during freezing of powder slurry, a unidirectional ice-ceramic structure is obtained. The frozen specimen is then subjected to freeze drying to sublimate the ice. The obtained capillary-porous ceramic specimen is consolidated by sintering. The sintering of the graded structure is modeled by the continuum theory of sintering.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.10
• /
• pp.1371-1376
• /
• 2014

In this paper, 4-phase switched reluctance motor(SRM) with 8-stator and 6-rotor pole structure is proposed for a high speed fan with a low voltage. The air blower has unidirectional rotation characteristics and requires a low torque ripple and noise as well as high efficiency. To achieve the requirements, voltage and current according to loading condition of limited specification is considered. Design process is to select the bore diameter, pole arc, york of stator and rotor to get a high torque and efficiency. To verify the validity of the proposed structure, finite element method(FEM) is employed to get the performances. And the converter for the proposed SRM is employed a 1.5q power converter for cost effectiveness. Prototype SRM is manufactured and tested, and the test results show this design is within the specification and good for the air blower applications.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.2
• /
• pp.1-7
• /
• 2011

The CFRP composite has a lot of merits such as mechanical characteristic, light and thermal resistance. For these merits, CFRP is applied to so many industrial area. In order to use the composite materials in the aircraft structures or machine elements, accurate surfaces for bearing mounting or joints must be provided, which require precise, machining. In this study, the specimens differentiating the stacking sequence of 5kinds were used. When drilling the carbon fiber reinforced plastics, it was checked on whether the stacking sequence reached any effect on the cutting force. Also relationship between the drill diameter is examined from the drilling experiment, which is the drilling of Fabric, Unidirectional specimen with ∅6mm, ∅10mm, ∅12mm cemented carbide drill. Considering cutting force and drilling diameter, the results are analyzed.

• ETRI Journal
• /
• v.43 no.5
• /
• pp.900-908
• /
• 2021

This paper proposes thermometer-code latches having five and six transistors for unidirectional and bidirectional thermometer-code shift-registers, respectively. The proposed latches omit the set and reset transistors by changing from two supply voltage nodes to the set and reset signals in the cross-coupled inverter. They set or reset the data by changing the supply voltage to ground in either of two inverters. They reduce the number of transistors to five and six compared with the conventional thermometer-code latches having six and eight transistors, respectively. The proposed thermometer-code latches were simulated using a 65 nm complementary metal-oxide-semiconductor (CMOS) process. For comparison, the proposed and conventional latches are adapted to the 64 bit thermometer-code shift-registers. The proposed unidirectional and bidirectional shift-registers occupy 140 ㎛² and 197 ㎛², respectively. Their consumption powers are 4.6 ㎼ and 5.3 ㎼ at a 100 MHz clock frequency with the supply voltage of 1.2 V. They decrease the areas by 16% and 13% compared with the conventional thermometer-code shift-register.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1278-1288
• /
• 2019

A DC-DC Non-Isolated Three-Port Cuk-Cuk (NI-TPCC) converter for interfacing renewable energy sources (RESs) such as Fuel Cell (FC) and Photovoltaic (PV) energy with a DC load is presented in this paper. It features single-stage power conversion from both of the input ports to the load port. The proposed NI-TPCC converter is designed based on the classical Cuk converter. The operational modes and power flow are analyzed in the continuous conduction mode (CCM), and the relationships among the port voltages are derived. Continuous currents in all three ports with less ripple enhance the performance of a fuel cell and its operating life. Furthermore, the output inductor is shared with both of the input ports, which reduces the number of active and passive components. The effectiveness of the designed NI-TPCC converter has been validated through simulation and experimental results.