• 한국건축시공학회지
• /
• 제12권2호
• /
• pp.230-242
• /
• 2012

Recently the Permanent Uni-wall System (PUS) has been developed which improved the disadvantage of the Cast-In-Place Concrete Pile (CIP) and could be used as permanent retaining wall. In this study, joints between PUS and floor systems were developed. From analyses of the characteristics of design and construction of PUS, shear friction reinforcements with couplers were adopted for shear design of the joints. Twelve types of joints were developed which were classified according to the types of floor structures, wale, and piles of PUS. Two typical joints were tested and the joints showed satisfactory behaviors on the points of shear strength, stiffness, and serviceability. Especially the shear strengths were much higher than the design strengths due to the shear keys which were by-products in splicing shear reinforcements. However, the shear strength of the joint is recommended to be designed by only shear friction reinforcement because shear key is not reliable and too brittle.

• Structural Engineering and Mechanics
• /
• 제76권4호
• /
• pp.479-489
• /
• 2020

This paper proposed a novel form of reinforced concrete (RC) shear wall confined with boundary columns. The structural effect of applying steel fiber reinforced concrete (SFRC) in the wall-column systems was studied. Three full-scale wall samples were constructed including two RC wall-RC column samples with different stirrup ratios and one RC wall-SFRC column sample. Low frequency cyclic testing was carried out to investigate the failure modes, hysteretic behavior, load-bearing capacity, ductility, stiffness degradation and energy dissipation. ABAQUS models were set up to simulate the structural behavior of tested samples, and good agreement was achieved between numerical simulation and experimental results. A further supplementary parametric study was conducted based on ABAQUS models. Both experimental and numerical results showed that increasing stirrup ratio in boundary columns did not affect much on load bearing capacity or stiffness degradation of the system. However, applying SFRC in boundary columns showed significant enhancement on load bearing capacity. Numerical simulation also shows that the structural performances of RC wall-SFRC column system were comparable to a wall-column system fully with SFRC.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.154-157
• /
• 2008

In korea, PV business has been growing fast since 2000. There are many ways to build PV module Among them, BIPV system(BIPV : building integrated system) using PV modules as external wall has been carried out research on and invested much. I suggest another way to apply the BIPV system BIPV SU(string unit) module is easier and faster to be installed and more economical than other BIPV module. In this paper. I will show how to make, and how to install this BIPV SU module.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2005년도 추계학술대회지
• /
• pp.153-158
• /
• 2005

표면에 부착된 수직벽 후방의 난류전단흐름을 입자영상유속계를 이용하여 조사하였다. 하부 틈새를 갖는 수직벽 후류영역에서는 박리 후 비정상적인(unsteady) 재순환 영역이 형성되었으며, 약 x=3H위치에서 전단층의 재부착 및 난류경계층으로의 재발달 과정이 나타났다. 수직벽 직전의 오목한(concave) 유선곡률과 수직벽 후방의 볼록한(convex)유선곡률의 영향은 수직벽 주위에서 가장 크게 나타나고, 하류로 나아감에 따라 전단층 주위 유체의 유입 등으로 그 영향이 박리 전단층 내에서 커다란 와구조가 연속적으로 발생하였다.

• 한국물환경학회지
• /
• 제20권3호
• /
• pp.206-214
• /
• 2004

Residual wall thicknesses, corrosion rates, and residual life of thirty four samples of cast iron pipes(CIPs) and ductile cast iron pipes(DCIPs) collected from water mains of B city were studied to estimate their remaining service life or optimum time of rehabilitation. The internal maximum corrosion depths of samples measured using a dial gauge after shot blasting were twice higher than the external in most cases. Therefore corrosion of water pipes was much more affected by internal water quality than soil. Residual wall thicknesses of DCIPs were higher than those of CIPs. That reason was thought to be that DCIPs have been protected from internal corrosion by lining cement mortar. Residual life calculated by maximum corrosion rate was ranged up to 44 years with 12.40 years average. Since most CIPs were much deteriorated, rehabilitation plan should be established soon in B city. Residual life of DCIP was 33.52 years average. When cement mortar lining is used up by neutralization of DCIPs. DCIP also should be rehabilitated.

• 태양에너지
• /
• 제11권2호
• /
• pp.41-50
• /
• 1991

본 연구는 상변화물질로써 용융점온도가 $62^{\circ}C$인 파라핀($C_{28}H_{58}$)과 용융점온도가 $79^{\circ}C$인 피로인산나트륨($Na_4P_2O_7{\cdot}10H_2O$)을 사용하여 축열 및 방열과정 시 잠열축열조내에서 각 상변화물질의 시간경과에 따른 온도특성 및 열전달현상을 실험적으로 규명한 것으로 각 상변화물질의 온도분포와 축열량 및 방열량을 계산하고 이를 비교, 검토한 것이다. 파라핀의 경우 축열과정초기에 자연대류 열전달현상으로 인하여 온도가 서서히 증가하는 반면 피로인산나트륨의 경우는 전도 열전달 현상의 지배적인 영향으로 인하여 축열과정 초기에 온도가 급격히 증가하는 형태로 나타났다. 또한 축열 및 방열과정 시 파라핀의 경우 tube의 상하부벽면에서의 온도변화와 중심부의 온도변화가 큰 차이를 보였으나 피로인산나트륨의 경우 tube의 상하부 벽면에서의 온도와 중심부에서의 온도는 큰 차이를 나타내지 않았다. 그리고 축열과정 시 동일질량에 대한 각 상변화물질의 축열량은 파라핀보다 피로인산나트륨이 약 16%정도 많은 것으로 나타났다.

• 태양에너지
• /
• 제15권3호
• /
• pp.29-38
• /
• 1995

본 연구는 화학열펌프 개발을 목적으로 비교적 고온영역에서 화학축열에 응용 가능 할 것으로 판단되는 무기수화물계 $Ca(OH)_2/CaO$ 가역 반응싸이클을 이용한 수화 탈수반응에 따른 충진층내 열이동에 대하여 실험적 검토를 행하였다. 그 결과 본 실험에서 얻은 열교환특성은 $Ca(OH)_2$ 열분해 탈수반응시 반응기 내의 시료층 상단부가 하단부에 비해 탈수반응이 느리게 진행되었으며 이러한 현상은 탈수반응이 하부에서 상부로 진행됨을 알 수 있었다. 또, 반응기내 반경방향에서의 $Ca(OH)_2$ 열분해 탈수반응에 따른 온도변화는 시료 중심부에서 상 하단부로 나타났으며 이는 열전도도에 의한 온도 강하로 중심부의 축열온도가 높음을 알 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제22권6호
• /
• pp.794-799
• /
• 2011

In order to reduce the oil consumption for a 2 stroke free piston hydrogen fueled engine, the behaviors of residual lubricant oil of the cylinder wall surface were visualized and oil mass emitted into exhaust port was measured by using research engine with cross-head and eccentric crankshaft. As the results, it was shown that characteristics of residual lubricant oil such as oil thickness and distribution were remarkably different from a conventional 4 stroke engine. It was also analyzed that these tendencies relied on the configuration and installed position of the exhaust port, piston pin boss and so on.

• Journal of Microbiology and Biotechnology
• /
• 제12권3호
• /
• pp.530-533
• /
• 2002

This paper describes the development of an enzymatic assay system for the identification of specific inhibitors of sortase, a transpeptidase that cleaves surface proteins of Cram-positive bacteria, from Staphylococcus aureus ATCC 6538p for antibacterial drug discovery. The coding region of the enzyme was amplified with the exception of the N-terminal membrane anchor sequence, cloned into a vector providing His-Patch-thioredoxin-tag at the N-terminus, expressed in Escherichia coli, and purified by metal chelate affinity chromatography. The enzyme activity was determined by quantifying increased fluorescence intensity upon cleavage of synthetic Dabcyl-QALPETGEE-Edans peptide. The results suggest that the developed in vitro assay system call be used in the search for sortase inhibitors In a short period of time.