• 한국음향학회지
• /
• 제10권5호
• /
• pp.37-45
• /
• 1991

일반 소형 승용차의 고속 주행시 발생하는 진동 중 조향휠의 원주방향의 진동인 shimmy 현상을 연구하였다. Shimmy 현상은 쾌적한 차량 설계단계에서 예측할 수 있고 그 원인을 추정할 수 있도록 조 향계의 모델링 및 이론해석을 하였으며 실험결과치와의 비교검토를 통하여 모델링에 대한 타당성을 검 증하였다. 검증된 모델링을 이용하여 조향계를 구성하는 각 부재의 감쇠, 강성, 타이어의 트레일 및 stabilizer bar 의 강성등의 변화가 조향휠 진동에 미치는 영향을 고찰하였다. 특히 shimmy 현상이 타이 어의 편마모등에 의한 unbalance mass에 얼마나 민감한가를 실험 및 이론적인 해석을 통하여 고찰하였다.

• 소음진동
• /
• 제3권3호
• /
• pp.279-283
• /
• 1993

A diagnostic method of anisotropy and asymmetry in rotor systems utilizing the two-sided directional spectra of the operating responses has been presented and tested with a laboratory flexible rotor-bearing system. The experimental results show that the directional spectra can be effectively used for the diagnosis of anisotropy and/or asymmetry in rotor systmes by the investigation of -1X and +2X components in the directional spectrum of unbalance and gravity responses.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권2호
• /
• pp.244-251
• /
• 1999

Large dynamic loads act on the rotor in rotary compressors. There are unbalance forces due to eccentric rotation parts and gas forces induced by the pressure difference between compression and suction gases. Rotor-journal bearing system is nonlinear since the stiffness and damping coef-ficients of the lubrication oil film are not constant in the bearings. in this paper the program for predicting the behaviors of rotor-journal bearing system of rotary compressor is developed. Finite element modeling is used to analyze the flexible rotor. The numerical results are compared with experimental results.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.150-158
• /
• 2009

A centrifugal turbo blower is one of the part to generate electric power of fuel cell electric vehicle(FCEV). In order to generate the electric power of FCEV, the centrifugal turbo blower operates at very high speed above 30,000rpm in order to increase the pressure of the air, which supplied to a stack of FCEV, using rotation of its impeller blades. Vibration which originated from the blower is generated by unbalance of mechanical components, rotation of bearings and rotating asymmetry that rotate at high speed. The vibration is transmitted to receiving structure through vibration isolators and it can causes serious problems in the noise, vibration and harshness(NVH) performance. Thus, the study about reducing this kind of vibration is an important task. Quantifying the effectiveness of vibration isolation can be effectively accomplished by using vibrational power flow because relative contributions of each isolator to the total vibration transmission can be easily represented. In this paper, vibrational power flow is applied to the centrifugal turbo blower mounted on FCEV in order to analyze the most dominant vibration transmitting path. As a result, the main contributor among four isolators is a mount #3 of the blower. Also, a 30 percent lowering of the mount #3 stiffness shows 34 percent decrement of vibrational power flow by the simulation.

• 한국음향학회지
• /
• 제10권2호
• /
• pp.13-22
• /
• 1991

회전체를 내포하는 회전기계에서 진동의 근원은 불평형 질량이다. 본 여구에서는 정적평형 방법을 이용하여 돌출 회전축에 설치된 회전체의 평형을 바로 잡았으며, phase angle method 와 four run method로부터 보정 질량을 산정하였다. 또한, 평형잡이 전후의 진동의 감쇠를 조사하였다. 실험결과 불평형 질량에 의해 발생하는 진동은 불평형의 효과를 제거함으로써 감쇠됨을 확인하였다. 특히 불평형 질량이 작을 때, 진동의 감쇠력에서 four run method가 phase angle method 보다 더 유효함을 입증하였다.

• Journal of Mechanical Science and Technology
• /
• 제16권12호
• /
• pp.1583-1593
• /
• 2002

This paper discusses the model validation and vibration suppression of an AMB flexible rotor via additional LQG controller. The main difficulty in the vibration suppression of the flexible rotor using AMB is to realize a controller that can minimize resonance without injuring the stabilized rigid modes. In order to solve this problem, simple scheme for system modeling and controller design are developed. Firstly, the AMB flexible rotor is stabilized with a PID controller, which leads to a new stable rotor-bearing system. Then, authors propose the model validation procedure using measured open-loop frequency responses to obtain an accurate model of the AMB flexible rotor system. After that, LQG controller with modal weighting is designed to suppress resonances of the stable rotor-bearing system. Due to the poor controllability and observability of flexible modes compared to rigid ones, balancing of two Gramians is prerequisite for the fair LQG controller design. Simulation with step disturbance and experimental results of unbalance response up to 10,000 rpm verified the effectiveness of the proposed scheme.

• 한국소음진동공학회논문집
• /
• 제18권9호
• /
• pp.972-981
• /
• 2008

The blower which is installed in a FCEV(fuel cell electric vehicle) may cause noise due to misalignment and unbalance of mechanical components that rotate at high speed. One of the key points in efforts to minimize the noise radiation from a blower is the knowledge of the main radiating component and the relation between the surface vibration of a blower and the sound pressure. In this research, the blower model is developed based on FEM(finite element method). FE(finite element) model is reliable by correlation of frequencies and MAC(modal assurance criterion) values between EMA(experimental modal analysis) and FEA(finite element analysis). This model is applied to predict the vibration of a blower by using inverse force identification method and predict the radiating noise by using BEM(boundary element method). Comparing the frequencies of resonance and those mode shapes between EMA and FEA, a structural modification of the FE model is evaluated for reducing the parameters of the blower noise.

• 한국소음진동공학회논문집
• /
• 제27권2호
• /
• pp.204-212
• /
• 2017

The rotor dynamics and balancing technic for rotating equipment during engineering and manufacture stage are to be carefully considered in order to minimize the operation troubles regarding vibration during commissioning stage. In this paper, the test rig, which includes the disks as balancing plane, is designed and manufactured, so that the characteristic of rotor dynamics can be analyzed such as critical speed and mode shape. The critical speed predicted through natural frequency analysis is verified by the actual measurement on bearing housing vibration during start-up condition of test rig. The low speed balancing and the operating speed balancing test are performed respectively with consideration of first critical speed, and the residual unbalance amounts are estimated in accordance with the relevant method described in API standard. In addition, the single and dual plane balancing are carried out on main disk and trim disk depended on phase information at each balancing step.

• Tribology and Lubricants
• /
• 제27권2호
• /
• pp.57-64
• /
• 2011

Hybrid air-foil magnetic bearing integrates two oil free bearing technologies synergetically to adopt the strengths of two bearings with minimizing their weaknesses. This paper presents bending mode vibration control of a flexible shaft supported by the hybrid air-foil magnetic bearing. An experiment set-up of a flexible shaft supported by the hybrid air-foil magnetic bearing is built. In order to verify the effectiveness of the hybrid bearing, unbalance responses of the flexible shaft supported by three different bearings: air-foil, magnetic and hybrid bearings are compared. Effect of load sharing between air-foil and magnetic bearings are investigated through changing the control gain and the rotor center position of magnetic bearing. The experimental results shows that the hybrid bearing can control the bending mode vibration of the flexible shaft effectively and an optimal performance can be achieved with an appropriate load sharing between the air-foil and the magnetic bearings.

• 한국정밀공학회지
• /
• 제30권10호
• /
• pp.1095-1101
• /
• 2013

The purpose of this study was to verify the effect on improvement of muscle strength unbalance according to load deviation protocol during whole body vibration exercise. Seventeen female volunteers (age $22{\pm}3$ years, height $160{\pm}4.9$ cm, weight $49{\pm}.8$ kg) participated in this experiment. The subjects performed squat exercise in WBV platform. Exercise were performed five set a day including 15 time a set, three days a week, and during 4 weeks. Vibration stimulus was 25Hz as frequency and intensity was dominant leg 1mm and non-dominant leg 4mm. The results in WBV group showed that the differences of peak torque in 16% were getting decreasing significantly after 4 weeks from 16.2% to 5.2%. This result means that WBV with load deviation protocol could provide muscle strength exercise for muscle strength balance. Our study found out that WBV of load deviation protocol could provide muscle strength exercise for improving muscle imbalance.