• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.581-586
• /
• 2020

In this paper, the design process and method for a compact wideband loop antenna for terrestrial digital TV (DTV) and ultra high definition (UHD) TV applications was proposed. Horizontal slits were added on the two circular sectors of the proposed loop antenna in order to miniaturize the existing wideband loop antenna consisting of a square loop and two circular sectors. A CPW transmission line was inserted in the center of the lower circular sector as a feed line. The CPW feed line was designed using the 75 ohm port impedance for DTV and UHD TV applications, and a tapered center-signal line was designed to improve the impedance matching. The final designed antenna was fabricated on an FR4 substrate with a thickness of 0.8 mm. The experiment results show that the proposed compact loop antenna operates in the frequency band of 444.3-820.1 MHz for a VSWR < 2, which fully covers the DTV and UHD TV bands.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.213-218
• /
• 2007

In this paper, we propose the design and fabrication on high frequency CMOS VCO for DS-UWB(Direct-Sequence Ultra-WideBand) applications using 0.18 ${\mu}m$ process. The complementary cross-coupled LC oscillator architecture which is composed of PMOS, NMOS symmetrically, is designed for improving the phase noise characteristic. The resistor is used instead of current source that reduce the 1/f noise of current source. The high-speed buffer is needed for measuring the output characteristic of VCO using spectrum analyzer, therefore the high-speed inverter buffer is designed with VCO. A fabricated core VCO size is $340{\mu}m{\times}535{\mu}m$. The VCO is tunable between 7.09 and 7.52 GHz and has a phase noise lower than -107 dBc/Hz at 1-MHz offset over entire tuning range. The measured harmonic suppression is 32 dB. The VCO core circuit draws 2.0 mA from a 1.8 V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.7
• /
• pp.380-388
• /
• 2014

Transmission methods for terrestrial UHDTV broadcasting have been actively studied in order to provide enhanced broadcasting service in many countries. Most of the countries are considering multi-carrier transmission methods based on OFDM and some of them have performed UHDTV experimental broadcasting by using the DVB-T2 standard with the adoption of an improved data compression technique. However, since single carrier transmission methods, which are known to be susceptible to multi-path fading, could remedy this defect by using the SC-FDE method where a frequency domain equalizer is utilized in the receiver, they may achieve a similar transmission performance with multi-carrier transmission methods. In consideration of these circumstances, we compare the transmission performances of two-type methods to provide a decision criterion on a suitable transmission method for UHDTV broadcasting.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.10
• /
• pp.3079-3094
• /
• 1996

Recently, the high-precision vibration attenuation technology becomes the essence fo the seccessful development of high-integrated and ultra-precision industries, and is expected to continue playing a key role in the enhancement of manufacturing technology. Vibration isolation system using an air-spring is widely employed owing to its excellent isolation characteristics in a wide frequency range. It has, however, some drawbacks such as low-stiffness and low-damping features and can be easily excited by exogenous disturbances, and then vibration of table is remained for a long time. Consequently, the need for active vibration control for an air-spring vibration isolation system becomes inevitable. Furthermore, for an air-spring isolation table to be successfully employed in a variety of manufacturing sites, it should have a guaranteed robust performance not only to exogenous disturbances but also to uncertainties due to various equipments which might be put on the table. In this study, an active vibration suppression control system using H.inf. theory is designed and experiments are performed to verify its robust performance. An air-spring vibration isolation table with voice-coil-motors as its actuators is designed and built. The table is modeled as 3 degree-of-freedom system. An active control system is designed based on $H_\infty$control theory using frequency-shaped weighting functions. Analysis on its performance and frequency responce properties are done through numerical simulations. Robust characteristics of$H_\infty$ control on disturbances and model uncertainties are experimentally verified through (i) the transient response to the impact excitation of the table, (ii) the steady-state response to the harmonic excitation, and (iii) the response to the mass change of the table itself. An LQG controller is also designed and its performance is compared with the $H_\infty$ controller.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.2
• /
• pp.93-98
• /
• 2018

This paper introduces the development of HF(NFC) and UHF band(13.56 MHz, 920 MHz) tag antennas, imbedded in a box. In dual band antennas, the HF band tag can be used to inspect the box using NFC, and the UHF band tag can be used for logistics. The dielectric constant of the box material is measured and used for simulation. The Ntag213 chip manufactured by NXP is used in HF loop antennas, since NFC is possible with Ntag213. For the UHF band, the Higgs-3 chip manufactured by Alien is used. The HF tag antenna is located at the center of the UHF tag antenna, and the location of the HF tag antenna is calculated while considering coupling effects. The designed tag can be used by both the bands for the purposes of logistics and authentication.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.2
• /
• pp.222-231
• /
• 2011

In this paper, we have proposed a method which can make it possible to stably transmit and receive data like the ARC-164 radio frequency hopping environment as a S/W packet modem with PSK modulation. This is a method that the S/W packet modem with PSK digital modulation and the use of PC sound cards change over from data to voice signals and then transmit/receive data. We confirmed not only that it is possible to solve the slow speed communication with the use of sending data through multi-channels and PSK modulation that has the ability to methodically improve transmission rates, but also that it is possible to send the state of frequency hopping stably. In conclusion, we've confirmed both tactical values that though the transmission rate may be a tad slow, a state of frequency hopping of more than 94% confidence plus voice and data can be sent via radio at the same time. In this paper, the proposed S/W packet modem is only an implemented S/W component, so when we apply it to aircraft that we don't consider EMC problems with, then we have the advantage of a wider use of conventional UHF/VHF/HF radio that is possible to voice communication. If we recognize these operational requirements, we can apply for a lot of field equipment efficiently.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.492-498
• /
• 2021

This feasibility study evaluated an optically transparent planar antenna using liquid salt-water as the conducting material. The most significant reason behind using liquid salt-water for transparent antenna applications is its excellent average optical transparency (OTav) (> 95% at a salinity of 40 ppt) compared to other typical solid transparent thin-film electrodes, such as indium tin oxide (ITO:> 73%) or multi-layer films (MLF: > 78%). Each conductive arm of the proposed dipole is constructed from a salt-water layer held between two clear planar acrylic layers (��r = 2.61, tan�� = 0.01, OTav > 90%) (acrylic/salt-water/acrylic; ASA) due to surface tension. To examine the electrical and optical properties of the ASA structure, the surface tension was measured to determine the thickness of the salt-water layer that finalized its sheet resistance and OTav. The average gain and efficiency of the antenna were 1.72 dBi and 74%, respectively, in the operating UHF (Ultra high frequency) band (470-771 MHz). Therefore, the proposed antenna can be a good candidate for applications as a transparent planar antenna using salt-water.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.11
• /
• pp.2047-2053
• /
• 2008

Auto-ID industries and their services have been improved since decades ago, and radio frequency identification (RFID) has been contributing in many applications. Product management can be the foremost example. In our industrial experiences, RFID in ultra high frequency (UHF) band provides much longer interrogation ranges than that of 13.56MHz; many more applications exist thereby. There should be several interesting and useful ideas on UHF RFID; however, those ideas can be limited due to the inevitable environmental circumstances that restrict the interrogation range in shorten value. This paper discusses the propagation interference among different types of readers (e.g, mobile RFID readers in stationary reader zone) in dense-reader environment. In most cases, UHF RFIDs in Korea will be dependent on the UHF mobile RFIDs. In this sense, the UHF mobile users accidently move into the stationary reader's interrogation zone. This is serious problem. In this paper, we analyze propagation loss and propose the effective channel allocation scheme that can contribute developing less-invasive UHF RFID networks. The simulation and practical measurement process using the commercial CAD tools and measurement equipments are presented.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.4
• /
• pp.686-691
• /
• 2012

Deviating from the exclusive frequency assignment, UWB has utilized much wider frequency range, worked independently without interfering other frequencies, and simultaneously enabled to increase more than hundreds of Mbps data transmission rate. In considering its high data rate and no interference, UWB certainly has an infinite and technical potential. In this paper, we studied the UWB technology as well as its technological trend, analyzed UWB antenna, and actualized a small antenna for wireless video streaming devices.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.254-262
• /
• 2009

This paper presents a novel simple filter design method based on a parallel short-ended coupled-line structure with capacitive loading for size reduction and ultra-broad rejection of spurious passbands. In addition, the introduction of a cross-coupling capacitor into the miniaturized coupled-line can create a transmission zero at the second harmonic frequency for better frequency selectivity and attenuation level. The aperture compensation technique is also applied to achieve a strong coupling in the coupled-line section. The influence of using the connecting transmission line to cascade two identical one-stage filters is studied for the first time. Specifically, such a two-stage bandpass filter operating at 2.3 GHz with a fractional bandwidth of 10% was designed and realized with low-temperature co-fired ceramic technology for application in base stations that need high power handling capability. It achieved attenuation in excess of -40 dB up to $4f_0$ and low insertion loss of -1.2 dB with the size of 10 mm ${\times}$ 7 mm ${\times}$ 2.2 mm. The measured and simulated results showed good agreement.