• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.3
• /
• pp.223-230
• /
• 2002

Titania photocatalytic oxidation reactors were studied to investigate degradation efficiencies of hydrocarbons. In general, it is well known phenomena that thin layered titania oxidizes most of hydrocarbons to carbon dioxide and water under UV light. In this study, degradation efficiencies were measured due to changes in reactor structures, UV sources, the number of titania coatings, and various hydrocarbon chemicals. It was proven that gas degradation efficiencies are related to such factors as UV transmittance of coating substance, collision area of surface, and gas flow rate. For packing type annular reactor, about 98% degradation efficiency was achieved for achieved for propylene of 500 ppm level at a flow rate of 100 ml/min. Several gases were also tested for double-coated titania thin film under the condition of continuous flow of 100 ml/min and 365 nm UV source. It was shown that degradation efficiencies were decreasing in the order: $C_3$ $H_{6}$, n-C$_4$ $H_{10}$, $C_2$ $H_4$, $C_2$ $H_2$, $C_{6}$ $H_{6}$ and $C_2$ $H_{6}$./. 6/./.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.178.1-178.1
• /
• 2014

본 연구에서는 RF스퍼터링법에 의하여 유리기판에 NiO를 40 nm만큼 증착시킨후, 30분 동안 각각 상온, $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$로 후 열처리 하였다. 박막의 전자적, 광학적 특성은 XPS (X-ray Photoelectron Spectroscopy), REELS (Reflection Electron Energy Loss Spectroscopy)와 UV-Spectrometer를 이용하여 =측정하였고, Hall Effect를 이용하여 전기적 특성을 측정하였다. XPS측정결과, $400^{\circ}C$ 후 열처리 한 NiO박막은 NiO 결합인 Ni2+가 줄어 들면서 금속 결합인 Ni0가 증가하면, 상온에서 띠틈이 4.0eV, 3.4eV로 줄어드는 것을 REELS로 확인 했다. 이 값은 UV-Spectrometer를 이용한 광학적 띠틈과 같음을 보였다. Hall Effect측정 결과 $400^{\circ}C$ 후 열처리한 샘플에서 P-type에서 N-type으로 바뀜을 보였으며, 비저항이 낮아지는 경향을 보였다. UV-Spectrometer를 이용한 광학적 특성을 측정해본 결과, 가시광선영역인 380 nm~780 nm에서의 투과율이 75%이상으로 투명전자소자로의 응용이 가능하다는 것을 보여 주었다.

• Journal of Microbiology and Biotechnology
• /
• v.13 no.4
• /
• pp.544-551
• /
• 2003

Interactive effects of UV-B and Cd on growth, pigment, photosynthesis, and lipid peroxidation have been studied in Anabaena, Microcystis, and Nostoc; all the tested cyanobacteria showed differential sensitivity to different dosage of UV-B and Cd alone as well as in combination. Phycocyanin was severely affected by UV-B and Cd by all the strains; the degree of pigment bleaching was most pronounced in Anabaena followed by Microcystis and Nostoc. $UV-B_2+Cd_2$ produced nearly 83, 78, and 65% inhibition of phycocyanin in Anabaena, Microcystis, and Nostoc, respectively. The above treatment also significantly decreased the contents of Chl ${\alpha}$ and carotenoid. Presence of capsule in Microcystis protected the phycocyanin bleaching as compared to decapsulated cells. Laboratory-grown Microcystis revealed about 75 and 80% inhibition, following $UV-B_2+Cd_2$ treatment, respectively. in capsulated and decapsulated cells. Damage caused by Cd was more pronounced than UV-B. Inhibition of photosynthesis did occur in all the test strains, being maximum in Anabaena. PS II was the most sensitive component of the electron transport chain, showing 84, 80, and 70% inhibition in Anabaena, Microcystis, and Nostoc, respectively. As compared to control, significant lipid peroxidation (6.5-fold higher) was observed in Anabaena with $UV-B_2+Cd_2$, $^{14}C-uptake$ was more susceptible to Cd and Uv-B than oxygen-evolution. Approximately 84, 80, and 76% inhibition of $^{14}C-uptake$ was observed in Anabaena, Microcystis, and Nostoc, respectively. Similarly, $UV-B_2+Cd_2$ inhibited APT content of Anabaena by 87%. This ,study suggests that inhibition of carbon fixation was due to decreased ATP content of the test cyanobacteria by UV-B+Cd, where Anabaena was the most sensitive and Nostoc the most tolerant.

• Korean Journal of Environmental Agriculture
• /
• v.18 no.1
• /
• pp.83-85
• /
• 1999

This study was conducted to find out analytical method for diesel fuel using uv-spectrophotometer in water samples. The optimum wavelength, detection limit and recoveries for desel fuel extracted with n-pentane were 257nm, $100{\sim}800mg/l$ and $102{\sim}121%$, respectively. This method were stable for measuring concentrations of desel fuel for 1 hour at $20{\pm}1^{\circ}C$ condition.

• Textile Coloration and Finishing
• /
• v.21 no.5
• /
• pp.16-20
• /
• 2009

Films of Poly(ethylene oxide), PEO, were modified to impart hydrophilicity via UV irradiation. The UV irradiation treatment produced new photo-oxidized groups of carbonyl and ether groups as indicated in ATR and ESCA analysis. It was found that water contact angle decreased from $15^{\circ}C$ to $10^{\circ}C$ and total surface energy of PEO increased from 54.2 mN/m to 76.6 mN/m with increasing UV energy, which was attributed to significant contribution of acid base interaction of the photo-oxidized PEO rather than nonpolar interaction originating from the dominant increase in Lewis acid parameter. The increased hydrophilicity and surface energy were also proved by the decreased water wetting time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.117-120
• /
• 2001

A new photoalignment material PFCPMI, poly[4-(fluorocinnamate)phenylmaleimide], was synthesized and the nematic liquid crystal (NLC) aligning capabilities on the photopolymer surface. The NLC pretilt angle generated by non-UV filter method on the PFCPMI surface was higher than that of the UV filter method. A good LC alignment by non-UV filter method was observed at $150^{\circ}C$ of annealing temperature. However, the alignment defect of the NLC by UV filter method was measured above $150^{\circ}C$ of annealing temperature. Consequently, the high pretilt angle and the good LC alignment in NLC using non-UV filter method can be acheived.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.117-120
• /
• 2001

A new photoalignment material PFCPMI, poly [4-(fluorocinnamate) phenylmaleimide], was synthesized and the nematic liquid crystal (NLC) aligning capabilities on the photopolymer surface. The NLC pretilt angle generated by non-UV filter method on the PFCPMI surface was higher than that of the UV filter method. A good LC alignment by non-UV filter method was observed at 150\`c of annealing temperature. However, the alignment defect of the NLC by UV filter method was measured above 150$^{\circ}C$ of annealing temperature. Consequently, the high pretilt angle and the good LC alignment in NLC using non-UV filter method can be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.423-428
• /
• 2002

The photoalignment material PFCPMI, poly[4-(fluorocinnamate)phenylmaleimide], was synthesized and the nematic liquid crystal(NLC) aligning capabilities on the photopolymer surface. The NLC pretilt angle geneated by non-UV filter method on the PFCPMI surface was higher than that of the UV filter method. A good LC alignment by non-UV filter method was observed at $150^{\circ}C$ of annealing temperature. However, the alignment defect of the NLC by UV filter method was measured above $150^{\circ}C$ of annealing temperatue. Consequently, the high pretilt angle and the good LC alignment in NLC using non-UV filter method can be acheived.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.567-568
• /
• 2021

In this paper, we design, fabricate, and test the performance of a cabin filter with LED modules of composite wavelengths containing UV-A and UV-C. Germs and air farms of the manufactured cabin filter confirmed sterilization capability in the sterilization test, and special chambers were manufactured to verify organic material decomposition capability in the organic compound decomposition test. Using colkates as photocatalytic was proved to be superior to using metal mash. The sterilization and air purification capabilities of the cabin filter produced throughout this study were verified through a similar environmental test.

• Journal of Sensor Science and Technology
• /
• v.18 no.4
• /
• pp.307-310
• /
• 2009

This paper describes the formation of porous 3C-SiC by anodization. 3C-SiC thin films were deposited on p-type Si(100) substrates by APCVD using HMDS(Hexamethyildisilane: $Si_2(CH_3)_6$). UV-LED(380 nm) was used as a light source. The surface morphology was observed by SEM and the pore size was increased with increase of current density. Pore diameter of 70 $\sim$ 90 nm was achieved at 7.1 mA/cm$^2$ current density and 90 sec anodization time. FT-IR was conducted for chemical bonding of thin film and porous 3C-SiC. The Si-H bonding was observed in porous 3C-SiC around wavenumber 2100 cm$^{-1}$. PL shows the band gap enegry of thin film(2.5 eV) and porous 3C-SiC(2.7 eV).