• The Korean Journal of Community Living Science
• /
• v.28 no.1
• /
• pp.143-154
• /
• 2017

This study was conducted to develop fabrics using non-toxic and eco-friendly natural dyes made from curcuma and coffee extract. The natural dyes were applied to non-printed cotton fabrics using the dip dyeing method, and the pattern was hand-printed onto the dyed fabrics to make dyed printed-fabrics. The four types of developed fabric samples were compared to analyze the effects of the dyeing materials and printing on the hygienic properties of curcuma- and coffee-dyed fabrics. The findings were as follows. First, air permeability of both curcuma- and coffee-dyed fabrics was greatly affected by the presence of patterns, although the type of dye did not seem to have an effect. Printing greatly reduced air permeability of the fabric, and coffee-dyed fabric showed greater reduction of dyeing method than curcuma-dyed fabric. Moisture regain also tended to decrease with printing, but the change was much smaller compared to air permeability. Second, increased UV blockage was observed in curcuma- and coffee-dyed fabrics with patterns compared to non-printed fabrics, showing that printing enhanced UV blocking. Third, deodorization rate tended to increase sharply for both curcuma- and coffee-dyed fabrics until 30 minutes and gradually increased thereafter to yield 30% for curcuma and 50% for coffee at 120 minutes, demonstrating higher deodorization of coffee dye. Coffee-dyed fabric showed an antibacterial rate about twice as high as that of curcuma-dyed fabric, and the observed data suggest that curcuma-dyed fabric had an insignificant level of antibiosis. Fourth, printing significantly enhanced wash, sunlight, and compound colorfastness of the two types of dyed fabrics. The effect of printing was most dramatic on sunlight and compound colorfastness, which are aspects in which natural dyed fabrics perform poorly in general. Eventually, the development and application of biologically- and environmentally-friendly fabrics with natural dyes correspond with increased interest towards the wellness and healthy attitudes of modern society.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.107-112
• /
• 2022

In this study, a silver paste capable of UV curing without using any solvent was developed. The viscosity and viscoelasticity of the silver paste developed as a solvent-free type were measured. And after printing the pattern by screen printing, an electrode coating film was formed by UV curing. Conductivity, pencil hardness, and adhesive force of the formed electrode coating film were evaluated. Finally, the curing characteristics of the electrode coating film were evaluated by TGA and FT-IR. Summarizing these results, in terms of conductivity, adhesion, and curing characteristics, it was found that Paste (4), that is, silver paste obtained by mixing 1.2 ㎛ spherical silver powder and 50 nm silver powder at 72:8% had the best physical properties.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.19 no.2
• /
• pp.68-78
• /
• 2001

UV-curable resin has the properties of quick-drying, thigh productivity at low temperature, energy savint, space saving, solventless, non-polluting and low-stinking, and thus, UV-curing system has been widely used in the fields of printing inks, adhesives, paints and coating agents. This study has been executed to micro-patterning used UV-curable resin, The micro-patterning properties of this photoresist were investigated under irradiation of UV light low pressure mercury lamp. When the exposed photoresist film was developed by pure water developer, the resolution of this photoresist was about 50$\mu\textrm{m}$.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.28 no.1
• /
• pp.65-75
• /
• 2010

Environmentally friendly, stencil and screen printing for cost-effective for maskless. In this study, UV -LED light source for the dispersion characteristics and high competence photoresist coating was prepared. Wavelength of 365nm UV-LED exposure device using the maskless lithography, 1.7kgf/$cm^2$ $2600mmH_2O$ the injection pressure and the suction pressure by using a dry photoconductor symptoms were dry emulsion on the market as a result, curing properties and adhesion, hardness, solvent resistance and excellent reproduction of fine patterns and ecological stencil technology was available and could be confirmed as a possibility.

• Proceedings of the KIEE Conference
• /
• 2007.11a
• /
• pp.104-105
• /
• 2007

In this study, characteristics of silver ink-jet printing were investigated under various substrate treatments such as substrate heating, hydrophobic coating, and ultraviolet(UV)/ozone soaking. Fluorocarbon(FC) film was spin-coated on the polyimide (PI) film substrate to obtain a hydrophobic surface. Although hydrophobicity of the FC film could reduce the diameter of the printed droplets, the singlet images printed on the FC film surface showed irregularities in the pattern size and the position of the printed droplet along with droplet merging phenomenon. The proposed UV/ozone soaking of the FC film improved the uniformity of the pattern size and the droplet position after printing and substrate heating was very effective way in preventing droplet merging. By heating of the substrate after UV/ozone soaking of the coated FC film, silver conductive lines of 78-116 ${\mu}m$ line were successfully printed at low substrate temperatures of $40^{\circ}C$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.6
• /
• pp.89-94
• /
• 2016

Consumer orientation requires that companies understand consumer needs and produce products that meet their expectations. This study proposes a new additive method that creates a polymer/metal bonding layer and thus can lighten the weight of helmets to develop a consumer-oriented 3D printing helmet. The composite solution is experimentally prepared with copper formate and a photopolymer resin. Stereolithography apparatus and photothermal reactions are introduced to fabricate an adhesive hybrid layer of copper metal and polymer. A UV pulse laser with a 355 nm wavelength was installed to simplify this process. Resistance, adhesion, and accuracy were investigated to evaluate the properties of the layer produced.

• Journal of Technologic Dentistry
• /
• v.42 no.3
• /
• pp.208-212
• /
• 2020

Purpose: This study aimed to analyze the shrinkage and expansion strain of ultraviolet (UV)-cured resin according to the wavelength of the light source and compare the shrinkage and expansion. Methods: We prepared the mold with according to the ISO 4049 specimen. The size of the circle in the mold was prepared with a height of 6.02 mm and a diameter of 4 mm. UV-curable resin for three-dimensional (3D) printing was injected into the circular mold. The control group was irradiated with a wavelength of 400~405 nm using UV-curing equipment (400 group), and the experimental group was irradiated with a wavelength of 460~465 nm (460 group). Both groups were produced ten specimens. The produced specimen was first measured with a digital micrometer. After the first measurement, the specimen was immersed in a constant temperature water bath for 15 days, after which the second measurement was performed, and the third measurement was taken after 30 days. The measured values were analyzed using the independent sample t-test (α=0.05). Results: In the non-immersion water tank, the contraction was 0.9% in the 400 group and 1.3% in the 460 group. In the constant temperature bath, the expansion was high at -0.4% in the 400 group for 15 days, and the smallest expansion was -0.03% for the 400 group for 30 days. There were significant differences between the two groups (p<0.05). Conclusion: The 400 group had a lower UV resin specimen strain than the 460 group. Therefore, it is recommended to use the wavelength required by the UV-curing resin.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1394-1399
• /
• 2007

Recently, Study of 3D freeform fabrication method was working in the various applications. For example, in the powder base, it's laminated using a binding method or laser sintering method. However, these methods are not suitable in the office environments because it dust with powder that is bad for health. In this paper, we introduce a method of 3D freeform fabrication using a curing of photo-polymer resin and construct a system has multi printing head. A photo-polymer curing method has simply fabrication process and high strength of manufacturing part. However, this method has a problem on the multi print-head system. Because multi-printing system has a other printing method compare with a single printing system. Therefore, we experiment a single head 3D printing and proposed a 3D printing method using a multi-piezo head.

• 프린팅코리아
• /
• v.14 no.8
• /
• pp.88-89
• /
• 2015

마이크로큐닉스(주)(대표이사 이병열)는 이스라엘 야브네(YAVNE)에 본사를 둔 Heret Printing이 MGI의 디지털 스팟 UV 코팅기 JETvarnish 3D와 핫포일 스댐핑 장비 iFOIL을 도입했다고 최근 밝혔다. 마이크로큐닉스(주)는 MGI의 JETvarnish 3D와 iFOIL 국내 총판을 맡고 있다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.227-228
• /
• 2007