• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.401-404
• /
• 2010

The ion-beam induced changes in the characteristics of gadolinium doped ceria (GDC) pellets have been studied by UV-visible spectroscopy (UV-vis), SEM, and XRD. Implanted ions were protons or Xe ions with the energy of 120 keV or 5 MeV. Densely sintered pristine GDC pellets have cubic fluorite structure and are brown in color. As the ion irradiation proceeded, its color gradually turned into light black and finally into dark black. XRD patterns of GDC pellets were closely related with ion energy and the penetration depth of X-ray. It showed that upon the ion irradiation (120 keV) the lattice parameter of the cubic fluorite phase just beneath the surface is increased.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.1
• /
• pp.11-15
• /
• 2018

In this study, we deposited silver nanoparticles on the nanocone array structure which was fabricated by the UV nanoimprint process for optical signal amplification. The deposition of the silver nanoparticles was based on the evaporation behavior of the solution droplet according to wettability of surface and the deposition pattern changed from the center of the droplet to the edge depending on the difference of thermal energy. The optical property of silver nanoparticles that were deposited on imprinted nanohole patterns was simulated by the Finite difference time domain (FDTD) analysis method, and it was confirmed that energy was concentrated around the silver nanoparticle of the finally fabricated structure.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.31-31
• /
• 2011

Lanasol dyes containing ${\alpha}$-bromoacrylamide or ${\alpha},{\beta}$-dibromopropionylamide group are used for wool dyeing. They are normally applied to wool under pH 4.5 to 6.5 at $100^{\circ}C$. Although wool fabric can be dyed to obtain deep colour, high light and wet fastness, the dyeing processes need long dyeing time at high temperature, with salt addition, which inevitably causes environmental problems. Grafting is a modification method for textile where monomers are covalently bonded onto the polymer chain. It can be initiated by ozone, ${\gamma}$ rays, electron beams, plasma, corona discharge and UV irradiation. Coloration by UV-induced photografting exhibits several advantages such as fast reaction rate, energy saving, simple equipment, easy exploitation and environmentally friendliness. Also it requires much lower energy compared to the conventional dyeing and less damage to the substrate. In this study, a direct sequential UV-induced photografting onto wool fabrics was discussed. To understand the graft polymerization mechanism further, several characterization methods were used. Moreover, the effects of several principal factors on the graft photopolymerization were investigated. Furthermore, the colorfastness results were compared with conventional dyeing methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.887-890
• /
• 1997

Recently micromachining using DPSSL(Diode Pumped Solid State Laser) with 3rd harmonic wavelength is actively studied in laser machining area. Micromachining using DPSSL have outstanding advantages as UV source comparing with excimer laser in various aspect such a maintenance cost, maskless machining, high repetition rate and so on. In this study micro-drilling of PCB type substrate which consists of Cu-PI-Cu layer was performed using DPSS Nd:YAG laser(355nm, wavelength) in vector scanning method. Experimental and numerical method(Matlab simulation, FEM) are used to optimize process parameter and control machining depth. The man mechanism of this process is laser ablation. It is known that there is large gap between energy threshold of copper and that of PI. Matlab simulation considering energy threshold of material is performed to effect of duplication of pulse and FEM thermal analysis is used to predict the ablation depth of copper. This study could be widely used in various laser micromachining including via hole microdrilling of PCB, and micromachining of semiconductor components, medical parts and printer nozzle and so on.

• Proceedings of the KAIS Fall Conference
• /
• 2005.05a
• /
• pp.274-276
• /
• 2005

본 논문에서는 유동층 화학기상증착법(FB CVB; Fluidized Bed Chemical Vapor Deposition)으로 광촉매가 박막증착된 비드를 제조하였고 제조된 광촉매코팅비드의 광반응성을 연속식 반응기에서 아세트알데히드의 분해능력을 측정하여 분석하였다. 광촉매가 박막증착된 비드의 FE-SEM 분석 결과 글라스 비드 위의 티타니아는 비교적 매끄럽게 증착되었고, 실리카 위의 티타니아는 입자의 형태로 증착되었으며 알루미나 위의 티타니아는 결정상을 이루며 증착됨을 확인 할 수 있었다. Acetaldehyde 기체의 광촉매에 의한 분해 실험을 진행하기 위해 연속식 반응기를 설계 제작하였고, 이 반응기를 사용하여 제조된 광촉매 코팅입자의 광반응성을 살펴보았다. 반응기는 가스 주입구와 출구를 갖고 있으며, 중심부에 UV 램프가 설치되었다. 반응기는 내열유리(pyrex)로 제작하였으며, 체적은 100 ml이다. 반응기 내부의 중심부에 UV 램프가 설치되고 UV 램프와 반응기 외부사이에 유동층 화학기상증착법에 의해 티타니아가 박막증착된 광촉매입자가 위치하여 광반응성을 평가하였다. 유량변화에 따른 광반응성을 측정하였으며, 알루미나에 광촉매를 증착시킨 제품의 경우 가스유량 100cc/min에서는 acetaldehyde가 $100\%$ 분해되고, 가스유량 500cc/min에서는 $50\%$정도 분해되는 것을 알 수 있었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.656-661
• /
• 2002

Multipass Ti:sapphire amplifier for the light source of lidar was developed in an angular-multiplexing, and the characteristics of output energy and spectrum was investigated. In the two-stage multipass amplifier, we obtained the maximum output energy of 42 mJ, the amplification gain of 21 dB and the output efficiency of 26% on the wavelength of 790 nm. In the tuning range of 715~930nm the spectral linewidth is 0.05 $cm^{-1}$ /. The conversion efficiencies of 35% for SHG at 780 m and 13% for THG at 390 nm are obtained respectively. The continuous tunabilities of 240~306 m UV region and 360~460 nm in deep-blue region could be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.173-176
• /
• 2011

The characteristic changes in ZnO thin film according to H- and O- plasma treatments have been studied by Photoluminescence (PL) spectroscopy at room temperature. The red shift of UV peak by 20-30 meV in PL spectra after plasma treatments is identified, which indicates that there are changes in the binding energy of bound exciton and/or the movement of energy levels of lattice defects and impurities. The width of UV peak is decreased after plasma treatments, which is believed to be closely related to the crystal quality of ZnO film. The increase of UV peak intensity after H-plasma treatment is also observed, and this could mean that the radiative recombination is strengthened because the hydrogen atoms in the plasma diffuse into the film where they passivate and neutralize the defects and the impurities.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1833-1836
• /
• 2008

Recently as the micro surface features become higher and diverse in their shapes, the releasing of the molded features becomes more crucial for manufacturing of the micro patterned products. The higher aspect ratio of the features or more complex shape of the features results in larger releasing force, elongation or cohesive failure of the features during the releasing. Another issue would be the uniformity of the released surface features after molding, especially for applications with large area surface. The micro patterned optical film, one of typical applications for micro surface features, consists of two layers, the thermoplastic base film and the micro formed UV resin layer. Therefore two interfaces are typically involved during the forming of this micro featured film; one is between the base film and the UV resin and another is between the resin and the pattern master. To improve the releasing of the molded surface features, the adhesive characteristic was investigated at these two interfaces. A PET film was used as a base film and two UV curable resins with different surface energy were prepared for different adhesiveness. Also the two different pattern masters were employed; one is made from brass-copper alloy and fabricated with PMMA. The adhesiveness at each interface was measured for some combinations of these base film, UV resins and the masters and the effect of this adhesiveness on the releasing was investigated.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.159-173
• /
• 2012

UV-Curing technology can be classified into two categories for radical curing and cation curing. It also has mainly focused on surface finishing technology to improve functionality of various substrates such as plastics and metals. On the other hand, EB technology has dealt with cross-linking reactions as well as polymerization process to create novel functional materials. Both technologies have advantages in energy utilizing efficiency and environmental friendly when compared to conventional thermoset coatings. Consequently, UV cured coatings also permits a reduction in the $CO_2$ and VOCs emitted in the drying and curing process. This review mainly shows radical curing technology which is commonly used in UV curing coatings and also describes the technology trends of cation curing which has been attracted attention recently.

• Journal of Environmental Science International
• /
• v.21 no.7
• /
• pp.845-853
• /
• 2012

Diethyl phthalate (DEP) is widely spread in the natural environment as an endocrine disruption chemicals (EDs). Therefore, in this study, ultrasound (US) and ultraviolet (UVC), including various applied power density (10-40 W/L), UV wavelengths (365 nm, 254 nm and 185 nm) and frequencies (283 kHz, 935 kHz) were applied to a DEP contaminated solution. The pseudo-first order degradation rate constants were in the order of $10^{-1}$ to $10^{-4}\;min^{-1}$ depending on the processes. Photolytic and sonophotolytic DEP degradation rate also were high at shortest UV wavelength (VUV) due to the higher energy of photons, higher molar absorption coefficient of DEP and increased hydroxyl radical generation from homolysis of water. Sonolytic DEP degradation rate increased with increase of applied input power and the dominant reaction mechanism of DEP in sonolysis was estimated as hydroxyl radical reaction by the addition of t-BuOH, which is a common hydroxyl radical scavenger. Moreover, synergistic effect of were also observed for sonophotolytic degradation with various UV irradiation.