• Journal of the Korean GEO-environmental Society
• /
• v.13 no.5
• /
• pp.5-12
• /
• 2012

Antibiotics have been considered emerging compounds due to their continuous input and persistence in environment. Due to the limited biodegradability and widespread use of these antibiotics, an incomplete removal is attained in conventional wastewater treatment plants and relative large quantities are released into the environment. In this study, it was determined the adsorption and photocatalysis kinetics of antibiotics (Sulfamethoxazole, SMX) with various catalyst (Titanium dioxide; $TiO_2$, Hydroxyapatite; HAP) conditions under UV/$TiO_2$/HAP system. In addition, the statistical analysis of response surface methods (RSM) was used to determine the effects of operating parameters on UV/$TiO_2$/HAP system. $TiO_2$/HAP adsorbent were found to follow the pseudo second order reaction in the adsorption. In the result of applied intrapaticle diffusion model, the constants of reaction rate were $TiO_2$=$0.064min^{-1}$, HAP=$0.2866min^{-1}$ and $TiO_2$/HAP=$0.3708min^{-1}$, respectively.The result of RSM, term of regression analysis in analysis of variance (ANOVA) showed significantly p-value (p<0.05) and high coefficients for determination values($R^2$=96.2%, $R^2_{Adj}$=89.3%) that allowed satisfactory prediction of second order regression model. And the estimated optimal conditions for Y(Sulfamethoxazole removal efficiency, %) were $x_1$(initial concentration of Sulfamethoxazole)=-0.7828, $x_2$(amount of catalyst)=0.9974 and $x_3$(reation time)=0.5738 by coded parameters, respectively. According to the result of intraparticle diffusion model and photocatalysis experiments, it was shown that the $TiO_2$/HAP was more effective system than conventional AOPs(advanced oxidation processes, UV/$TiO_2$ system).

• Journal of Korean Society on Water Environment
• /
• v.25 no.1
• /
• pp.90-95
• /
• 2009

This study investigates the oxidative degradation of N-nitrosodimethylamine (NDMA), a probable human carcinogen, by advanced oxidation process (i.e., UV process). The experiments were performed with various pH, initial concentration, UV intensity, and addition of $H_2O_2$ or $TiO_2$ on UV process. The results showed that the direct UV photolysis was the most effective treatment method. The lower pH, intial concentration and higher intensity of UV stimulated higher NDMA removal. However, addition of oxidant ($H_2O_2$, $TiO_2$) slows down photochemical treatment of NDMA since the oxidant can filter out the UV light and block it to reach the NDMA molecules. Dimethylamine (DMA) and nitrite were found to be a major byproduct from NDMA oxidation. To evaluate the chronic toxicity effects of UV-treated NDMA on the growth of microalgae, "Skeletonema costatum", was studied as long term experiments. Results demonstrated that after the 13 days exposure the chronic toxicity was decreased about 15% with application of UV process on NDMA degradation.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.228-234
• /
• 2010

In this paper, Fe-$TiO_2$ and Fe-fullerene/$TiO_2$ composite photocatalysts were prepared with titanium (IV) n-butoxide (TNB) by a sol-gel method. $TiO_2$, Fe-$TiO_2$ and Fe-fullerene/$TiO_2$ were characterized by scanning electron microscopy (SEM), Transmission electron microscope (TEM), specific surface area (BET), X-ray diffraction analysis (XRD) and energy dispersive X-ray spectroscopy (EDX). The photocatalytic activities were evaluated by the photocatalytic oxidation of methylene blue (MB) solution. XRD patterns of the composites showed that the photocatalyst composite contained a typical single and clear anatase phase. The surface properties shown by SEM presented a characterization of the texture on Fe-fullerene/$TiO_2$ composites and showed a homogenous composition in the particles for the titanium sources used. The EDX spectra for the elemental identification showed the presence of O, C and Ti elements. Moreover, peaks of the Fe element were observed in the Fe-$TiO_2$ and Fe-fullerene/$TiO_2$ composites. The degradation of MB solution by UV-light irradiation in the presence of photocatalyst compounds was investigated in complete darkness. The degradation of MB concentration in aqueous solution occurred via three kinds of physical phenomena: quantum efficiency of the fullerene; organo-metallic reaction of the Fe compound; and decomposition of $TiO_2$. The degradation rate of the methylene blue solution increased when using Fe-fullerene/$TiO_2$ compounds.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.4
• /
• pp.173-177
• /
• 2010

Thermal stabilizing effect of $Yb^{3+},\;Er^{3+}$ codoping into $TiO_2$ powder prepared by sol-gel method and its upconversion characteristics were analyzed. The effect of $TiO_2:Yb^{3+},\;Er^{3+}$ ions on crystallinity and phase transition was studied by X-ray diffraction (XRD). The change of band-gap energy induced from Yb and Er codoping was analyzed by UV-Vis. The band-gap energy of $TiO_2$ have been slightly narrowed by $Yb^{3+},\;Er^{3+}$ codoping, which indicated that the $Yb^{3+},\;Er^{3+}$ ions can enhance the photo-catalytic property of $TiO_2$. green and red up-conversions of $Yb^{3+}$ and $Er^{3+}$ co-doped $Y_2O_3:Yb^{3+},\;Er^{3+}$ phosphor were analyzed by PL equipped with 980 nm laser.

• Journal of Korean Society of Water and Wastewater
• /
• v.11 no.4
• /
• pp.133-141
• /
• 1997

In order to treat the landfill leachate, $UV/TiO_2/H_2O_2$ system connected with biological treatment was investigated, and proper pretreatment methods were examined to reduce the load on the system considering economical and technical efficiency. It was more profitable to put $H_2O_2$ into the system in the early stage for the sample which was treated with $H_2SO_4$ to decrease alkalinity and with $FeCl_3-6H_2O$ flocculation. Because the required reaction time run up by increasing $H_2O_2$ input amount, though the COD was reduced slightly, the optimal $H_2O_2$ input amount should be determined for the desired COD and the economical efficiency. The appropriate way to get the lowest COD in the shortest time was the method to treat the sample which was controlled to pH 3.5 after adjusting to pH 12 and put 500 ppm $H_2O_2$ into the system. In that case, to increase $H_2O_2$ input amount was not profitable for the system efficiency. The sufficient photocatalytic excited time was required to reduce the photocatalytic decomposition time for the sample which was gone through the alkali state.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.515-520
• /
• 2008

We fabricated 10 nm-$TiO_2$ thin films for DSSC (dye sensitized solar cell) electrode application using ALD (atomic layer deposition) method at the low temperatures of $150^{\circ}\;and\;250^{\circ}$. We characterized the crosssectional microstructure, phase, chemical binding energy, and absorption of the $TiO_2$ using TEM, HRXRD, XPS, and UV-VIS-NIR, respectively. TEM analysis showed a 10 nm-thick flat and uniform $TiO_2$ thin film regardless of the deposition temperatures. Through XPS analysis, it was found that the stoichiometric $TiO_2$ phase was formed and confirmed by measuring main characteristic peaks of Ti $2p^1$, Ti $2p^3$, and O 1s indicating the binding energy status. Through UV-VIS-NIR analysis, ALD-$TiO_2$ thin films were found to have a band gap of 3.4 eV resulting in the absorption edges at 360 nm, while the conventional $TiO_2$ films had a band gap of 3.0 eV (rutile)${\sim}$3.2 eV (anatase) with the absorption edges at 380 nm and 410 nm. Our results implied that the newly proposed nano-thick $TiO_2$ film using an ALD process at $150^{\circ}$ had almost the same properties as thsose of film at $250^{\circ}$. Therefore, we confirmed that the ALD-processed $TiO_2$ thin film with nano-thickness formed at low temperatures might be suitable for the electrode process of flexible devices.

• Korean Journal of Crystallography
• /
• v.12 no.3
• /
• pp.177-181
• /
• 2001

We have studied superhydrophilic properties of TiO₂thin films in relation with those crystal structures due to the heat treatments. Thin films were fabricated on Si (100) wafers using a conventional Sol-Gel method. Following drying and sintering processes, TiO₂film had an anatase phase with additional heat treatment at 500℃, an rutile phase at 1000℃, and a mixture of anatase and rutile phase at 750℃. All these films got hydrophilic even without any UV illumination. Especially the sample treated at 750℃ had a superhydrophilic contact angle of 5°. We suggested that the superhydrophilic films should have a mixture of anatase and rutile phase for the best performance. The hydrophilic TiO₂films were slowly degraded into the hydrophobic state in the dark room but quickly recovered back with les than 1 hour of UV illumination.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.4
• /
• pp.190-196
• /
• 2007

Dye sensitized solar cells(DSSC) are the most promising future energy resource due to their high energy efficiency, low production cost, and simple manufacturing process. But one problem in DSSC is short life time compared to silicon solar cells. This problem occurred from photocatalytic degradation of dye material by nanometer sized $TiO_2$ particles. To prevent dye degradation as well as to increase its life time, the transparent coating film is needed for UV blocking. In this study, we synthesized nanometer sized $TiO_2$ particles in sols by increasing its internal pressure up to 200 bar in autoclave at $120^{\circ}C$ for 10 hrs. The synthesized $TiO_2$ sols were all formed with brookite phase and their particle size was several nm to 30 nm. Synthesized $TiO_2$ sols were coated on the backside of fluorine doped tin oxide(FTO) glass by ink jet printing method. With increasing coating thickness by repeated ink jet coating, the absorbance of UV region (under 400 nm) also increases reasonably. Decomposition test of titania powders dispersed in 0.1 mM amaranth solution covered with $TiO_2$ coating glass shows more stable dye properties under UV irradiation, compared to that with as-received FTO glass.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.5
• /
• pp.745-748
• /
• 2002

A novel titania sol for the preparation of hydrophilic TiO2 films was synthesized from TiCl4. TiO2 films were prepared by spraying the sol on glass substrates and the hydrophilic properties of the films were invest igated with illumination of UV light. The contact angle of a water drop on the films decreased to less than 7˚, which indicates the excellent hydrophilicity of the TiO2 films.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2008.04a
• /
• pp.627-629
• /
• 2008