• 동력기계공학회지
• /
• 제5권1호
• /
• pp.21-26
• /
• 2001

This paper represents the turbulent intensity, the turbulent kinetic energy and Reynolds shear stress in the X-Y plane of cone type swirl gas burner measured by using X-probe from the hot-wire anemometer system. The experiment is carried out at flowrate 350 and $450{\ell}/min$ respectively in the test section of subsonic wind tunnel. The turbulent intensity and the turbulent kinetic energy show that the maximum value is formed in the narrow slits distributed radially on the edge of a cone type swirl burner, hence, the combustion reaction is anticipated to occur actively near this region. And the turbulent intensities ${\upsilon}\;and\;{\omega}$ are disappeared faster than the turbulent intensity u due to the inclined flow velocity ejecting from the swirl vanes of a cone type baffle plate of burner. Moreover, the Reynolds shear stress $u{\upsilon}$ is distributed about three times as large as the Reynolds shear stress $u{\omega}$ in the outer region of the cone type gas burner.

• 한국지반공학회논문집
• /
• 제26권7호
• /
• pp.93-106
• /
• 2010

현장 열응답 시험을 통해 지중 유효 열전도도를 산출하여 각 보어홀의 성능을 비교하기 위해 강원도 원주 현장에 6개의 보어홀을 시험 시공하였다. 6개의 보어홀은 그라우트 종류와 첨가재 종류, 지중열교환기 파이프 단면에 따른 영향을 검토하도록 시공되었다. 그라우트 재료는 벤토나이트와 시멘트를 사용하였으며 첨가재는 천연규사와 흑연, 파이프 단면은 기존 U-tube 파이프 단면과 유입과 유출 파이프 사이에 파이프를 추가로 삽입한 새로운 3공형 파이프 단면을 적용하였다. 현장 열응답 시험으로 산정한 지중 유효 열전도도 결과는 시멘트 그라우트로 시공한 보어홀의 경우가 벤토나이트 그라우트로 시공한 경우에 비해 전열 성능이 향상됨을 보였으며 흑연을 추가로 사용한 경우가 천연규사만 사용한 경우보다 높은 효율을 보였다. 또한, 유입과 유출 파이프 사이에 물을 채워 부분적 단열 구간을 형성한 새로운 3공형 파이프 단면의 경우가 기존 U-tube 파이프 단면에 비해 높은 효율을 보였다. 가상 건물에 대한 지중열교환기 설계를 수행하여 지중열교환기 시공비를 비교한 결과, 시멘트 그라우트에 첨가재로 천연규사와 흑연을 함께 사용한 경우가 벤토나이트 그라우트에 첨가재로 천연규사를 사용한 기존의 시공방법 보다 낮은 시공비로 설계가 가능하였다. 마지막으로 본 현장 열응답 시험결과를 바탕으로 일련의 경제성 분석을 통하여 새로이 제시된 첨가제와 3공형 파이프 단면의 적용성을 평가하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권6호
• /
• pp.360-366
• /
• 2000

This paper presents the fabrication and test of a micropump consisting of a pair of Al flap valves and a phase-change type actuator. The actuator is composed of a heater, a silicone rubber diaphragm and a working fluid chamber. The diaphragm is actuated by the vaporization and the condensation of the working fluid. The micropump is fabricated by the anisotropic etching, the boron diffusion and the metal evaporation. The forward and the backward flow characteristics of the flap valves illustrate the appropriateness as a check valve. Also, the flow rate of the micropump is measured. When the square wave input voltage of 8 V, 70% duty ratio and 2 Hz is applied to the heater, the maximum flow rate of the micropump is $97\muell/min$ for zero pressure difference.

• Nutrition Research and Practice
• /
• 제14권3호
• /
• pp.286-297
• /
• 2020

BACKGROUND/OBJECTIVES: This study compared the perception of customers from Korea and the U.S. on the attributes of different formats of menu labeling The specific objectives were 1) to compare the customers' perceived usefulness, ease-of-understanding, clarity, and attractiveness of different formats of menu labeling between Korea and the U.S.; and 2) to compare the customers' use intention to different formats of menu labeling between Korea and the U.S. SUBJECTS/METHODS: A survey was conducted in Korea and the U.S. The participants were allocated randomly to view 1 of the 7 restaurant menus that varied according to the following types of menu labeling formats: (type 1) kcal format, (type 2) traffic-light format, (type 3) percent daily intake (%DI) format, (type 4) kcal + traffic-light format, (type 5) kcal + %DI format, (type 6) traffic-light + %DI format, and (type 7) kcal + traffic-light + %DI format. A total of 279 Koreans and 347 Americans were entered in the analysis. An independent t-test and 1-way analysis of variance were performed. RESULTS: Koreans rated type 4 format (kcal + traffic light) the highest for usefulness and attractiveness. In contrast, Americans rated type 7 (kcal + traffic light + %DI) the highest for usefulness, ease-of-understanding, attractiveness, and clarity. Significant differences were found in the customers' perceived attributes to menu labeling between Korea and the U.S. Americans perceived higher for all the 4 attributes of menu labeling than Koreans. CONCLUSIONS: The study is unique in identifying the differences in the attributes of different formats of menu labeling between Korea and the U.S. Americans rated the most complicated type of menu labeling as the highest perception for the attributes, and showed a higher use intention of menu labeling than Koreans. This study contributes to academia and industry for practicing menu labeling in different countries using different formats.

• 소성∙가공
• /
• 제13권8호
• /
• pp.678-688
• /
• 2004

The U-draw bending operation is known as a representative test method for springback evaluation of sheet metals since the sheet in U-draw bending operation undergoes stretching, bending and unbending deformations occurred at the stamping process. In this study, a simplified approach was proposed for predicting springback and side-wall curls of tailor-welded blank in U-draw bending operations, using moment-curvature relationships derived for sheets undergoing stretching, bending and unbending deformation. Two different welded strips were adopted to compare the effects of weld-line locations on the springback. One (type A) was welded along the centerline of the strip-width and the other (type B) was welded along the centerline of the strip-length. To investigate the effect of different thickness combination on the springback, the tailor-welded strips were joined by the laser welding process and consisted of three types of thickness combinations of sheets, SCP1 0.8t ＊ SCP1 1.2t, SCP1 0.8t ＊ SCP1 1.6t and SCP1 0.8t ＊ TRIP 1.0t. Some calculated results by the simplified formula were compared with experimental results.

• 한국구조물진단유지관리공학회 논문집
• /
• 제2권2호
• /
• pp.202-208
• /
• 1998

To investigae the effect of anchorage type of carbon fiber sheet (CFS) on flexural behavior of RC beams, the loading test of RC beams reinforced with CFS was conducted in variable of anchorage Type such as bolting anchorage and U type anchorage using CFS. This study can be summarized as follows ; It is confirmed experimentally that the bolting anchorage and U type anchorage with CFS is very effective to delay the bond failure and prevent the peeling of CFS. Also, the anchorage type applied with this study is very effective to improve the ductility compared with the improving of maximum flexural strength of RC beams. It is believed that the anchorage type used this study must secure the ductile capacity of above 3 for the flexural strengthening of RC beams. In the future, it is required to obtain the data about anchorage type of CFS for utilization of field work as well as investigate the ductile capacity of conventional study of anchorage type

• 대한본초학회지
• /
• 제38권2호
• /
• pp.9-16
• /
• 2023

Objectives : Many people use natural soap instead of commercially available bar type general soap for skin care. They tend to prefer cp (cold process) type soaps that go through a sufficient maturation process in formulation. The purpose of this study was to investigate the efficacy of PCPS (placenta cp soap). Methods : The researcher selected 36 subjects, 28 as the experimental group and 8 as the control group. I asked participants to wash their face twice a day in the morning and evening, and the period was set for 6 weeks. The researcher had the people who were selected as the control group use a commercially available foam cleanser, meanwhile the experimental group use PCPS. They performed a skin test before the start of the test, and the change status was continuously investigated after 2 weeks, 4 weeks, and 6 weeks after using the soap. Results : In the case of U zone oil and pores, there was a significant decrease and in the case of skin tone, there was a significant increase in the group of using PCPS. In T zone oil change, there was no significant effect in both the experimental group and the control group. Conclusion : In the case of PCPS, it is recommended to use it in the effect of reducing the size of pores and increasing skin tone, but it can reduce u-zone oil content.

• 한국가스학회지
• /
• 제5권3호
• /
• pp.45-50
• /
• 2001

개방형 기화기는 해수를 이용하여 열교환을 수행함으로써 액체상태의 액화천연가스를 천연가스로 기화시키는 역할을 한다 86년부터 가동된 U-tyre 기화기는 천연가스생산과 관련된 중요설비 중 하나로서, 기화기 튜브는 항상 해수내에서 운전되고 있으며 기화기 튜브와 파이프사이의 용접부에서 해수로 인한 부식이 진행되고 있다. 본 연구에서는 용접부에서의 국부적인 부식원인을 찾기 위해 이종금속부식의 가능성을 평가해 보았으며 또한 비파괴적인 방법을 이용하여 부식피트의 깊이를 측정하고 유한요소를 통한 안전성 평가에 목적을 두었다. 이종금속부식가능성에 대하여 용접부 각 부위별로 시료를 채취하여 3.5$\%$(wt.) NaCl 용액내에서 모재와 용접부위의 부식전위를 측정하였으며, 비파괴 검사를 통한 잔류두께측정은 tangential radio-graphy 시험이 가장 신뢰성 있는 기법임이 확인되었다. 미세한 부식피트가 발생된 경우에는 표면형상 복제기법을 적용하였다. 비파괴적인 방법을 이용하여 산출된 부식피트의 깊이와 형상을 근거로 2차원 유한요소 해석을 수행함으로써 내압으로 인한 기화기 튜브의 안전성을 평가할 수 있었다.

• 한국지반공학회논문집
• /
• 제32권7호
• /
• pp.5-14
• /
• 2016

최근 들어 경제적이고 친환경적인 에너지 활용을 위하여 지열에너지의 필요성이 점차 증대되고 있다. 특히 지열히트펌프 시스템(geothermal heat pump system)으로 불리는 지열 냉난방 시스템의 적용성이 계속 확대되고 있다. 이러한 지열히트펌프 시스템에서 지반의 열전도도와 열확산계수와 같은 지중 열물성은 설계 과정에서 매우 중요한 변수이기에 현장 열응답 시험(thermal response test)을 통해 지반의 열전도도를 산출해야 한다. 본 논문에서는 U와 2U 타입의 지중 열교환기를 매립지 지반에 설치한 후 48시간 동안 현장 열응답 시험을 수행하였으며 지반의 열전도도 뿐만 아니라 지반의 열확산계수를 비선형 회귀분석을 통해 산정할 수 있는 방안을 제시하였다. 또한 지중 열교환기가 설치된 지반의 시료를 채취하여 실내 열물성 실험을 수행하였으며 이를 현장 열응답 시험을 통해 도출된 지반의 열전도도 및 열확산계수 값과 비교하였다.

• 한국패류학회지
• /
• 제31권1호
• /
• pp.61-67
• /
• 2015

The occurrence of 'algal bloom', caused by the mass proliferation of phytoplankton, causes serious problems in streams and lakes in Korea. Therefore, in this study, the phytoplankton filter-feeding trait of Unio douglasiae, a type of freshwater clam, was used to reduce the algal bloom in outdoor water tanks during the summer. This involved the construction of a U. douglasiae cultivation apparatus, wherein 1,000 clams were divided into 8 rectangular baskets arranged in the shape of an empty square. The control tank was manufactured in exactly the same shape within the water tank, but without the addition of clams. The algal bloom-reducing effect of U. douglasiae was confirmed by the measurement of (and comparing between) the water quality at the center and periphery of the test and control cultivation apparatus. Water quality measurements included the measurement of water temperature, pH, turbidity, dissolved oxygen (DO) content, and chlorophyll-${\alpha}$ concentrations; the water quality was measured twice a month between June and November 2014.The results of these analyses did not show a significant difference in water quality (temperature, pH, turbidity, DO) between the center and periphery of the test and control tanks. However, the chlorophyll-${\alpha}$ concentration was observed to be much lower at the center of the test tank compared to that at the center and periphery of the control tank, as well as at the periphery of the test tank. This was believed to be a result of the U. douglasiae surrounding the center of the test tank, which prevented the influx of plankton from the periphery. Accordingly, the results of these analyses suggest the possibility that U. douglasiae cultivation could reduce the proliferation of algal blooms in lakes and streams during the summer. In particular, these results indicate possible improvements in U. douglasiae activity (reduction in algal blooms) by their effective arrangement in the water bodies.