• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.159-159
• /
• 2009

RF 스퍼터링법을 이용하여 유리기판위에 ZnO:Al 박막을 증착하고 다양한 조건 하에서 후 열처리를 실시하여 이에 따른 박막의 구조적, 전기적 및 광학적 특성과 HCl 습식 식각 후의 표면형상 변화를 조사하였다. ZnO:Al 투명전도막은 우수한 전기적, 광학적 특성, 수소 플라즈마 안정성 및 저 비용 등으로 실리콘 박막 태양전지 전면 전극용으로 많은 관심을 받고 있다. 기존의 비정질 실리콘 박막 태양전지용으로 많이 사용되고 있는 상용 Asahi-U형 ($SnO_2:F$) 투명전도막의 경우는 수소 플라즈마에 대한 안정성이 낮고 입사광의 장파장 대역에서의 낮은 산란특성으로 인하여 실리콘 박막 태양전지의 고효율화를 위한 적용에 한계를 나타내고 있다. 이를 개선하기 위하여 스퍼터링법으로 우수한 전기적 특성을 갖는 ZnO:Al 박막을 제조한 후 습식 식각을 통한 표면형상 변화를 통하여 입사광의 산란특성을 향상시키는 방법이 개발되어 많은 연구가 이루어지고 있다. 본 연구에서는 2.5 wt%의 $Al_2O_3$가 함유된 ZnO 타겟을 이용하여 ZnO:Al 박막을 RF 스퍼터링으로 증착한 후 $N_2$ 분위기와 진공 분위기 하에서 다양한 시간과 온도에 따라 후열처리를 하여 열처리 전 박막과의 물질 특성을 상호 비교하고 1%로 희석된 HCl로 습식 식각하여 열처리 전 박막의 구조적 특성이 습식 식각 후의 박막 표면형상 변화에 미치는 영향을 조사하였다. 이로부터 후열처리를 통한 ZnO:Al 투명전도막의 특성을 최적화하고 Asahi-U형 투명전도막과의 특성 비교를 통하여 실리콘 박막 태양전지용 전면전극으로의 적용 가능성을 조사하였다.

• Journal of Korea Water Resources Association
• /
• v.38 no.7 s.156
• /
• pp.527-535
• /
• 2005

The computation of normal depth is very important for the design of channel and the analysis of water flow. Drainage pipe generally has the shape of curvature like circular or U-type, which is different from artificial triangular or rectangular channel. In this case, the computation of normal depth or the derivation of equations is very difficult because the change of hydraulic radius and area versus depth is not simple. If the ratio of the area to the diameter, or the hydraulic radius to the diameter of pipe is expressed as the water depth to the diameter of pipe by power law, however, the process of computing normal depth becomes relatively simple, and explicit equations can be obtained. In the present study, developed are the explicit normal depth equations for circular and U-type pipes, and the normal depth equation associated with Hagen (Manning) equation and friction factor equation of smooth turbulent flow by power law is also proposed because of its wide usage in engineering design.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.732-739
• /
• 2016

In Korea, the summer is hot and humid, and much electricity is consumed for air conditioning. Thus, the simultaneous usage of an indirect evaporative cooler and a common air conditioner could reduce the sensible heat and save electricity. This study developed a U-type cross-counter flow indirect evaporative cooler (IEC) made of plastic and paper. The efficiencies were compared with those of a cross-flow IEC. The specimen was $500mm{\times}500mm{\times}1000mm$. the results show that the indirect evaporation efficiencies of the cross-counter flow sample were 6-21% higher than those of the cross-flow sample. The pressure drops of the cross-counter sample were 51-66% higher. Thermal analysis based on the -NTU method predicted the experimental data within 10%. The electrical energy saved by the use of the cross-counter flow IEC was larger than that of the counter flow IEC, and the difference increases with the velocity. However, the the cross-counter IEC is two times larger than the cross-flow IEC, which may increase the material cost and water usage.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.11a
• /
• pp.211-214
• /
• 2007

In this paper, we have designed microstrip antenna if 800[MHz] band It will be able to integrate TRS(Trunked Radio System), GSM(Global System for Mobile telecommunication) band including the CDMA(Code Division Multiple Access) band we designed repeater and a base station antenna which is possible at the ship and marine of safety. It is improves a narrow bandwidth problem of microstrip antenna. It had U-shaped feeding structure at a rectangular patch And ground or feeding structure used between dielectric constant(${\varepsilon}_T$ = 2.1), patch or feeding structure used between dielectric constant(${\varepsilon}_T$ =1). So it used a duplex resonance effect Designed frequency bandwith(V5WR 2:1) if the antenna showed good characteristic of $780[MHz]{\sim}1.83[GHz]$ to 2.61[GHz]. Also the E-plan and H-plan all profit 9.4[dBi] above, the 3[dB] beam width showed the characteristic over the E-plan and H-plan $60^{\circ}$ to be improved.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.1
• /
• pp.83-97
• /
• 2011

In this study, the seismic details of a concrete-encased, U-shaped steel beam-to-RC column connection were developed. Three specimens of the beam-to-column connection were tested under cyclic loading to evaluate the seismic performance of the connection. The test parameters were the beam depth and the column section shape. The depths of the composite beams were 610 and 710 mm, including the slab depth. For the RC columns, a square section and a circular section were used. Special details using diagonal re-bars and exterior diaphragm plates were used to strengthen the connections with the rectangular and circular columns, respectively. The test results showed that the specimens exhibited good strength, deformation, and energy dissipation capacities. The deformation capacity exceeded 4% interstory drift angle, which is the requirement for the Special Moment Frame.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.3
• /
• pp.189-196
• /
• 2004

The RC wale-steel beam stud connection may have smaller moment and shear resistance because the tensile and shear capacity of the studs are limited by the depth of RC beam. Especially, they are subjected to compressive axial load. This paper describes the experimental works to develop the connection details of RC wale-steel beam joints subjected to shear and axial loads. Shear connectors developed in this study are closed C type deformed bar, opened C type deformed bar, and U type deformed bar. From shear test, the shear performance of RC wale-steel beam joint with the developed connectors are compared with the stud connection. Test results indicated that the developed connectors were very effiecive to increase the shear strength.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.509-516
• /
• 1999

In this paper, it is designed a microstrip U-slotted patch antenna with double resonances to enhance the bandwidth. In the design of an U-slotted patch antenna, there are considered the input impedance, the width of patch, the total length of the slot, the height of foam, the position of the probe and the radius of feed pin. The broadband behavior of antenna can be obtained by adjusting the length and width of the slot. The radiation from the antenna is linear polarized with the E-paine parallel to the vertical slots and the H plane parallel to horizontal slot. The radiation pattern, impedance locus, and VSWR of the antenna are calculated using "ENSEMBLE" software, and compared with the experimental results. Experimental results show that the bandwidth for VSWR $\le$ 2:1 is about 28.6%, a directivity 14.18dBi at 6.040GHz. 6.040GHz.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.57-60
• /
• 2008

Maglev is a system that a train runs levitated above a rail. Therefore it is very important to maintain a constant levitation gap for achieving serviceability and ride comfort. This study is a cooperation research subject of the 3-1 subject, performance improvement of maglev track structures, of the Center for Urban Maglev Program in Korea, started in 2006. The aim of this study is development of rapid constructions of bridge superstructure for maglev. At present, precast deck is widely used because of its superiority to cast-in-place concrete on quality and the term of works. The research group suggested basic systems of maglev guideway with PSC-U type and trapezoidal open steel box type girder, and precast deck, cooperating with Korea Railroad Research Institute, the managing institute of the 3-1 subject. In this study, a mock-up consisted of girders, decks and rail was fabricated and test was performed for constructability, serviceability and maintenance evaluation of PSC U-type girder, precast deck, and new guide rail system.

• Progress in Medical Physics
• /
• v.14 no.1
• /
• pp.54-67
• /
• 2003

The voltage-dependence of N-type calcium current inactivation is U-shaped with the degree of inactivation roughly mirroring inward current. This voltage-dependence has been reported to result from a purely voltage-dependent mechanism. However, $Ca^{2＋}$-dependent inactivation of N-channels has also been reported. We have investigated the role of $Ca^{2＋}$ in N-channel inactivation by comparing the effects of $Ba^{2＋}$and $Ca^{2＋}$ on whole-cell N-current in rat superior cervical ganglion neurons. For individual cells in-activation was always larger in $Ca^{2＋}$ than in $Ba^{2＋}$ even when internal EGTA (11 mM) was replaced with BAPTA (20 mM). The inactivation vs. voltage relationship was U-shaped in both divalent cations. The enhancement of inactivation by $Ca^{2＋}$ was inversely related with the magnitude of inactivation in $Ba^{2＋}$ as if the mechanisms of inactivation were the same in both $Ba^{2＋}$ and $Ca^{2＋}$. In support of this idea we could separate fast ( ${\gamma}$ ～150 ms) and slow ( ${\gamma}$ ～ 2500 ms) components of inactivation in both $Ba^{2＋}$and $Ca^{2＋}$ using 5 sec voltage steps. Differential effects were observed on each component with $Ca^{2＋}$ enhancing the magnitude of the fast component and the speed of the slow component. The larger amplitude of fast component indicates that the more channels inactivate via this pathway with $Ca^{2＋}$ than with $Ba^{2＋}$, but the stable time constants support the idea the fast inactivation mechanism is identical in $Ba^{2＋}$and $Ca^{2＋}$. The results do not support a $Ca^{2＋}$-dependent mechanism for fast inactivation. However, the $Ca^{2＋}$-induced acceleration of the slowly inactivating component could result from a $Ca^{2＋}$-dependent process.

• Transactions of Materials Processing
• /
• v.3 no.1
• /
• pp.51-62
• /
• 1994

Cup drawing test and U-bending test were performed to evaluate the friction characteristics of sheet materials for the different deformation modes involved in stamping process. The coefficient of friction calculated from the each test was compared to that obtained from the draw bead friction test. It was clarified that the cup drawing test could be simply used for evaluating the friction characteristic of sheet material in deep drawing process with high contacting pressure. However the U-bending test is suitable to evaluate the frictional characteristic of sheet material in bending process with low contacting pressure.