• 한국재료학회지
• /
• 제12권8호
• /
• pp.669-675
• /
• 2002

CrN film coated by AIP method, improved the mechanical properties (Hardness, Roughness, wear and fatigue) of Ti-6Al-4V alloy. The properties were studied using GXRD, XPS, Hardness, Roughness, wear and fatigue testers. CrN thin film thickness was about 7.5$\mu\textrm{m}$ and grew with (111) orientation. Hardness of CrN thin film was very high (Hv 1390) and roughness of the surface layer was greatly improved (Ra=0.063$\mu\textrm{m}$) compared with matrix alloy (Ra=0.321$\mu\textrm{m}$). Such changes of hardness and roughness could be contributed to improving the wear resistance and fatigue life. Striation like pattern with dimples and voids, a typical fatigue fracture mode, was observed throughout the specimen.

• 펄프종이기술
• /
• 제43권4호
• /
• pp.67-75
• /
• 2011

Sulfuric acid hydrolysis is a typical approach for producing cellulose nanocrystals. The method has been widely used, but it has a disadvantage of low yield of cellulose nanocrystals compared to mechanical method. To expand the application of cellulose nanocrystals in practical, we should be able to produce them with higher yield and the controlled properties. In this study, therefore, we intended to investigate the effect of sulfuric acid hydrolysis condition on the characteristics of the prepared cellulose nanocrystals. The concentration of sulfuric acid, temperature and hydrolysis time were varied, and the yield as well as diverse properties including the morphology, size and zeta potential were examined. We could obtain cellulose nanocrystals up to 70% of yield and found that the properties were dependent on the reaction condition. It would be helpful to select an appropriate condition for producing cellulose nanocrystals.

• Applied Science and Convergence Technology
• /
• 제24권3호
• /
• pp.47-52
• /
• 2015

The correlation between admittance and dielectric spectroscopy of dielectric relaxation in lead scandium noibate, have been investigated. Lead scandium niobate, with composition $PbSc_{0.5}Nb_{0.5}O_3$, was prepared by conventional solid state synthesis. Conductance Y'(G), susceptance Y"(B) and capacitance C of lead scandium niobate as a function of frequency and temperature were measured. From the temperature-dependence of RLC circuit, insight into physical significance of the dielectric properties of lead scandium niobate is obtained. The relative strong frequency dependent of dielectric properties in lead scandium niobate is observed, and the phase transition occurred at a broad temperature region. Also, the value of critical exponent ${\gamma}$=1.6 showed on heating process. The long relaxation times part enlarged diffuse by conductivity effects with increasing temperature, and the ordering between $Sc^{3+}$ and $Nb^{5+}$ in PSN influences complex admittance and dielectric properties. Confirmed the typical characteristic of lead-type relaxor in the Raman spectra of lead scandium niobate and major ranges are between 400 and $900cm^{-1}$.

• 한국세라믹학회지
• /
• 제30권7호
• /
• pp.549-556
• /
• 1993

Interfacial shear strength plays an important role in determining the mechanical properties of a fiber-reinforced ceramic composites. In this study, the effect ofinterlayer thickness on mechanical properties of Nicalon-fiber-reinforced SiC composites fabricated via polymer solution infiltration/chemical vapor infiltration (PSI/CVI) was studied. It was found that the flexural strength and fracture toughness of the composites were increased with the interlayer thickness and showed maximum value at the interlayer thickness of 0.66${\mu}{\textrm}{m}$. Typical flexural strength and fracture toughness of Nicalon-fiber-reinforced SiC composites with interlayer thickness of 0.66${\mu}{\textrm}{m}$ were 391.7$\pm$34.6MPa and 15.1$\pm$1.8MPa.m1/2, respectively.

• Carbon letters
• /
• 제13권3호
• /
• pp.157-160
• /
• 2012

In this work, iron oxide ($Fe_3O_4$) nanoparticles were deposited on multi-walled carbon nanotubes (MWNTs) by a simple chemical coprecipitation method and $Fe_3O_4$-decorated MWNTs (Fe-MWNTs)/polypyrrole (PPy) nanocomposites (Fe-MWNTs/PPy) were prepared by oxidation polymerization. The effect of the PPy on the electrochemical properties of the Fe-MWNTs was investigated. The structures characteristics and surface properties of MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy were characterized by X-ray diffraction and X-ray photoelectron spectroscopy, respectively. The electrochemical performances of MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy were determined by cyclic voltammetry and galvanostatic charge/discharge characteristics in a 1.0 M sodium sulfite electrolyte. The results showed that the Fe-MWNTs/PPy electrode had typical pseudo-capacitive behavior and a specific capacitance significantly greater than that of the Fe-MWNT electrode, indicating an enhanced electrochemical performance of the Fe-MWNTs/PPy due to their high electrical properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.632-635
• /
• 2003

[ $(Ba,Sr,Ca)TiO_3$ ] powders, prepared by the sol-gel method, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen printing techniques on alumina substrates. The dielectric properties were investigated for various composition ratio and $Nb_2O_5$ doping contents. All the BSCT thick films, sintered at $1420^{\circ}C$, showed the typical XRD patterns of a perovskite polycrystalline structure. The Curie temperature and the relative dielectric constant decreased with increasing Ca content and $Nb_2O_5$ doping amount. The relative dielectric constant, dielectric loss and tunability of the BSCT(50/40/10) thick films doped with 1.0wt% $Nb_2O_5$ were 1410, 0.65% and 17.29% respectively.

• Journal of Electrochemical Science and Technology
• /
• 제4권4호
• /
• pp.163-170
• /
• 2013

Tantalum anodic oxide film was prepared in citric acid solution of various concentrations and the prepared Ta anodic oxide film was characterized by various electrochemical techniques and X-ray photoelectron spectroscopy (XPS). The prepared Ta anodic oxide film showed typical n-type semiconducting properties and the dielectric properties were strongly dependent on the citric acid concentration. The variation of electrochemical and electronic properties was explained in terms of electrolyte anion incorporation into the anodic oxide film, which was supported by XPS measurements.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2005년도 학술발표회 논문집
• /
• pp.413-417
• /
• 2005

A lattice model of a typical bridge column section is analyzed, and results are presented. The lattice is built as an ensemble of line elements and masses, that can capture strain rate dependency of concrete material. The research mainly breaks up into two parts: First, a micro level analysis of the material is executed, and control parameters of the governing equations are derived by matching the results with the common macroscopic properties of concrete material. Then, the properties exhibited by the micro model, which extends the classical material properties are applied to the mesoscale model. Hence, the analysis of the target structure can be performed. In the mesoscale analysis, ramp-like impulse loads are applied at different velocity, so that the contribution of the material level rate dependency to the global behavior of the structure can be tracked.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.615-619
• /
• 2003

Temperature and frequency dependence of dielectric and electrical properties was investigated in cerium and manganese doped Sr$\_$0.6/Ba$\_$0.4/Nb$_2$O$\_$6/(60SBN) ceramic system. Structural deformation of 60SBN by dopants did not appeared. 1350$^{\circ}C$-10 h sintered specimen had higher densification than 1250$^{\circ}C$-10 h sintered one, to which dielectric properties are related. That the feature of dielectric maxima peaks was typical Diffusive Phase Transition (DPT), it was explained by "random-field Ising model". Even though 60SBN has large dielectric loss at high frequency above 100 ㎑, it is desirable for optical applications because of low dielectric loss at low frequency. From Arrhenius plot of temperature, the activation energy was calculated to 0.45-0.49 eV.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.421.2-421.2
• /
• 2014

We report on the growth of ZnO nanorods (NRs) grown on graphite and silicon substrates via an all-solution process and characteristics of their heterojunctions. Structural investigations indicated that morphological and crystalline properties were not significantly different for the ZnO NRs on both substrates. However, optical properties from photoluminescence spectra showed that the ZnO NRs on graphite substrate contained more point defects than that on Si substrate. The ZnO NRs on both substrates showed typical rectification properties exhibiting successful diode formation. The heterojunction between the ZnO NRs and the graphite substrate showed a Schottky diode characteristic and photoresponse under ultraviolet illumination at a small reverse bias of -0.1 V. The results showed that the graphite substrate could be a good candidate for a Schottky contact electrode as well as a conducting substrate for electronic and optoelectronic applications of ZnO NRs.