• Wind and Structures
• /
• 제34권2호
• /
• pp.161-171
• /
• 2022

This paper presents a failure type assessment curve method to judge the failure type of transmission tower segments. This novel method considers the equivalent static wind load characteristics and the transmission tower members' load-bearing capacities based on numerical simulations. This method can help judge the failure types according to the relative positions between the actual state points and the assessment curves of transmission tower segments. If the extended line of the actual state point intersects with the horizontal part's assessment curve, the segment would lose load-bearing capacity due to the diagonal members' failure. Another scenario occurs when the intersection point is in the oblique part, indicating that the broken main members have caused the tower segment to fail. The proposed method is verified by practical engineering case studies and static tests on the scaled tower segments.

• Korean Journal of Acupuncture
• /
• 제27권1호
• /
• pp.13-22
• /
• 2010

Objectives: The information on the depth where pulse wave appears is as important as pulse waveform. The aim of this study was to classify pulse pattern using pressure-height(P-H) volume-curve by 5 applied pressure levels to find out the information on the depth of pulse and interpret the floating & sinking pulse in oriental medical pulse diagnosis. Methods: We used 3 dimensional pulse imaging analyser (DMP-3000, DAEYOMEDI Co., Korea), which measures radial pulse waveforms noninvasively by way of tonometric method at 5 applied pressure levels, and shows P-H volume-curves by applied pressure. 448 subjects were enrolled, pulse waveforms were measured and the P-H volume-curves were gained on the three locations of Chon, Kwan, and Cheok. Results: Gained P-H volume curves were classified into 3 types ; increase type, decrease type, and increase-decrease type. Increase-decrease type appeared more often on Chon and Kwan, while increase type appeared more often on Cheok. In a few cases, decrease-type appeared on Chon and Kawn, however it never appeared on Cheok. Conclusions: Through the classification of pulse by P-H volume-curve, we gained the information on the depth of pulse. We speculate the decrease type as floating pulse, the increase-decrease type as middle pulse, and the increase type as sinking pulse in oriental medical pulse diagnosis. After more researches on P-H volume-curve by applied pressure, the P-H volume-curve may be used as an important factor for pulse diagnosis.

• 동력기계공학회지
• /
• 제18권1호
• /
• pp.22-31
• /
• 2014

This paper introduced the new calibration algorithm of a straight-type five-hole pressure probe necessary for calculating three-dimensional flow velocity components. The new velocity data reduction method using both a commercial two-dimensional curve-fitting program and the zone partition method of a calibration map was firstly introduced in this study. This new calibration method can be applied up to the wide flow angle of ${\pm}80^{\circ}$ despite of using a five-hole pressure probe because this data reduction method showed a comparatively good performance in calculating yaw and pitch angles from the calibration map.

• Communications for Statistical Applications and Methods
• /
• 제16권2호
• /
• pp.349-361
• /
• 2009

In this paper, we derive the approximate maximum likelihood estimators of the shape parameter and the scale parameter in a Weibull distribution under multiply Type-II censoring by the approximate maximum likelihood estimation method. We develop three modified empirical distribution function type tests for the Weibull distribution based on multiply Type-II censored samples. We also propose modified normalized sample Lorenz curve plot and new test statistic.

• 대한화학회지
• /
• 제7권2호
• /
• pp.96-105
• /
• 1963

The weight decrease curves of 18 kinds of polymers have been measured by thermobalance at the same condition where temperature is increased $1^{\circ}C$ per minutes under nitrogen or air atmosphere. The curves are further differentiated to obtain rate curve of weight decrease. Those curve offer a method to compare relative thermal stability, effects of oxygen or modes of thermal degradation of polymers qualitatively. The curves could be classified into following four types: Polystyrene, polymethylmethacrylate and acetal polymer belong to the first type. Those polymers depolymerize mainly into corresponding monomers, weight decrease curves are steepy up to perfect vaporization of polymers and rate curves show a relatively sharp peak. (Type I) Polyvinyl chloride represents the second type. This polymer decomposes with splitting off of hydrogen chloride. The thermogravimetric curve rises rapidly at first, then level off at the moderate weight decrease and gradually rises. Polyvinyl acetate also belongs to this class. (Type II) The modification of the second type is represented by polyester. The curve at the early stage is less steep, the leveling off at the next stage is less clear and the final rising of the curve is steeper than the normal second type. Polyamide, polyurethane, and polycarbonate belong to this type. (Type II') The thermal decomposition of the third type polymers is more complex than that of others. Various irregular chain scissions including side chain splitting and depolymerization to monomers occur simultaneously. The weight of the polymer decreases gradually and the rate curve does not show sharp peaks. Polyvinyl alcohol and diene polymers belong to this type. (Type III) Generally, polycondensation polymers are more stable toward heat than addition polymers and polymers having aromatic nucleus show good thermal stability. Polymers having tertiary carbon atoms such as polystyrene or polypropylene and acetal resin start decomposition under airatmosphere at the temprature below $50^{\circ}C$ or more of the temperature where the polymers start decomposition under nitrogen atmosphere.

• 한국지반공학회논문집
• /
• 제24권11호
• /
• pp.121-131
• /
• 2008

슬러리월 연직차수벽 시공시, 지반을 트렌치 형태로 굴착하고, 굴착시공 중 굴착면 붕괴에 대한 안정성을 유지하기 위하여 벤토나이트와 물을 혼합한 슬러리를 트렌치에 채운다. 이렇게 채워진 벤토나이트 슬러리로 인하여 필터케이크(filter cake)이라 불리는 얇고 투수성이 낮은 층이 트렌치벽 표면에 형성되며, 슬러리가 제거 된 이후에도 굴착면에 잔존하여 연직차수벽에서의 순간변위시험(slug test) 해석 결과에 중요한 영향을 미친다. 본 연구에서는 기존에 개발된 수치해석 프로그램 Slug-3D를 수정하여 순간변위시험 해석시 필터케이크의 영향을 고려하는 방법을 제시하고 이를 통하여 정확한 연직차수벽의 투수계수를 산출하도록 하였다. 필터케이크의 영향을 고려하기 위하여 Slug-3D에서는 차수벽과 토양층의 경계면에 불투수조건(no-flux)을 경계조건으로 설정하여 해석을 수행하였다 또한 투수계수 산정에서 기존의 타입커브법(type curve method)을 이용하기 위하여 개선된 type curve를 도출하였고, 선형 커브피팅법(line-fitting method)를 필터케이크가 존재하는 연직차수벽에 적용할 수 있도록 수정 보완하였다. 본 논문에서 제안된 필터케이크를 고려한 해석방법은 EMCON(1995)에 의해 수행된 현장시험 결과의 재해석을 통하여 타당성을 검토하였다. 또한, 본 연구에서 얻어진 결과를 Choi and Daniel(2006)에 의해 수행된 필터케이크가 존재하지 않는 경우의 순간변위시험 해석결과와 비교를 통해 필터케이크 고려가 반드시 필요함을 보여준다.

• 전기학회논문지
• /
• 제57권6호
• /
• pp.966-971
• /
• 2008

Free-piston engine system is a new type energy converter which uses a linear motion of piston by using linear generator. In free-piston engine system, the piston is not connected to a crank-shaft. The major advantages of free-piston engine system are high efficiency and low mechanical loss from the absence of motion conversion devices. Linear generator of free-piston engine system is used as generator and starting motor. In design step, considering of back-emf and detent force characteristics for generating mode and thrust and control characteristics for starting mode is needed. In this research, generating mode of flat-type linear generator and tubular-type linear generator is analyzed by finite element analysis method and starting mode of both type linear generators is analyzed by using capability curve. Capability curve is plotted from electrical parameters of both type linear generator and motion profile is calculated from mechanical parameters.

• Journal of Ship and Ocean Technology
• /
• 제10권2호
• /
• pp.24-36
• /
• 2006

Ship hullform is usually designed with a curve network, and smooth hullform surfaces are supposed to be generated by filling in (or interpolating) the curve network with appropriate surface patches. Tensor-product surfaces such as B-spline and $B\'{e}zier$ patches are typical representations to this interpolating problem. However, they have difficulties in representing the surfaces of irregular topological type which are frequently appeared in the fore- and after-body of ship hullform curve network. In this paper, we proposed a method that can automatically generate discrete $G^1$ continuous B-spline surfaces interpolating given curve network of ship hullform. This method consists of three steps. In the first step, given curve network is reorganized to be of two types: boundary curves and reference curves of surface patches. Especially, the boundary curves are specified for their surface patches to be rectangular or triangular topological type that can be represented with tensor-product (or degenerate) B-spline surface patches. In the second step, surface fitting points and cross boundary derivatives are estimated by constructing virtual iso-parametric curves at discrete parameters. In the last step, discrete $G^1$ continuous B-spline surfaces are generated by surface fitting algorithm. Finally, several examples of resulting smooth hullform surfaces generated from the curve network data of actual ship hullform are included to demonstrate the quality of the proposed method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1613-1616
• /
• 2005

In this paper, we developed an algorithm of generating cam contour curve for hinge mechanism of folder-type mobile phone. The main feature of this hinge mechanism is that we can operate uniform torque to open or close the mobile phone. We divided the opening or closing intervals of the cam into finite sub-intervals, and then we determined the cam contour curve of each sub-interval as a parabolic curve. Finally, these finite parabolic curves form the total cam contour. We can design single cam, which composed moving cam with contour curve and fixed cam that plays only roller, and twin cam with contour curve that is made up the pair of two cams symmetrically.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2003년도 ISIS 2003
• /
• pp.90-93
• /
• 2003

The function, which represents the closed curve, is found from the sampling data by S-System in this study. Two methods are proposed. One is the extension of S-System. The data x and y are regarded as input data, and the data z=0 as output data. To avoid the trap into the invalid function, the judgment points (x$\_$j/, y/sug j/) are introduced. They are arranged in the inside and the outside of the closed curve. By introducing this concept, the functions representing closed curve are found by S-System. This method is simple because of a little extension of S-System. It is, however, difficult for the method to find the complex function like a hand-written curve. Then another method is also proposed. It uses the system incorporating the argument function. The closed curve can be expressed by the argument function. The relatively complex function, which represents the closed curve like a hand-written curve, is found by utilizing argument function.