• Journal of radiological science and technology
• /
• v.20 no.2
• /
• pp.49-55
• /
• 1997

This study was carried out to investigate radiographical and operating conditions of X-ray units and exposure doses to patients during chest radiography, so that the results could provide basic data used for reducing the exposure dose and for providing the diagnostic information with better quality. The conditions and exposure doses of 100 X-ray units mainly used for chest radiography were examined and also 100 radiological technologists mainly handling those apparatus at 76 medical facilities in Pusan were surveyed using a questionnaire from October 1 to December 31 in 1995. The following results were obtained from the study : 1. It was found that most units were capable of taking a high tube voltage radiography by showing 67% of the units equipped with the maximum tube voltage of 150 kV, 94% with more than 500 mA for the rating capacity and 85% with the full wave type of a signal phase. 2. For actual chest radiographical conditions, however, 80% of the units were operated at $60{\sim}100\;kVp$ and only 14% at 100 kVp and over for the high tube voltage. 3. The average exposure time was less than 0.1 second, and eighty four percent of the units adapted the X-ray tube currents ranging from 200 to 300 mA, 80% the focus-film distances between 180 and 210 cm, and 63% the focus sizes of more than 2.0 mm. 4. Most units(98%) employed additional filters made of aluminum, 75% the thickness of filters less than 2.0 mm, and only 2 units the compound filters. 5. Ortho chromatic system was only adopted in 13% of screen film system for the units, and 73% used the grid ratio at 8 : 1 for the low tube voltage during chest radiography. 6. The average exposure dose of all X-ray units during chest radiography was $371\;{\mu}Sv$ with a difference of about 16 times between the minimum to the maximum, and $386\;{\mu}Sv$ both at hospitals and at health centers, followed by $380\;{\mu}Sv$ at general hospitals and $263\;{\mu}Sv$ at university hospitals without showing any statistically significant differences. In conclusion, since patients during chest radiography at medical facilities in Pusan exposed to high levels of radiation, it is recommended that appropriate added filters and grids necessary for the high tube voltage radiography and high-speed screen systems should be adopted and used as soon as possible in order to reduce exposure dose to the patients.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.161-161
• /
• 2010

InAsSb alloy system 은 HgCdTe 를 대체하는 적외선 광소자 및 검출기 등에 응용이 가능한 유망한 물질이지만 정확한 유전함수 및 전이점의 연구는 미흡한 실정이다. 본 연구에서는 타원 편광 분석법을 이용하여 1.5 ~ 6 eV 의 분광 영역에서 As 조성비를 각기 (x = 0, 0.127, 0.337, 0.491, 0.726 및 1.00) 다르게 한 $InAs_xSb_{1-x}$ alloy의 유전함수를 측정하였다. 또한 표면에 자연산화막을 제거하기 위하여 Methanol 과 DI Water 로 표면을 세척 한 후 $NH_4OH$, Br in Methanol, HCl 등으로 적절한 화학적 에칭을 하여 산화막을 제거함으로서 순수한 InAsSb 의 유전함수를 측정할 수 있었다. 측정된 InAsSb 유전함수를 Standard analytic critical point line shape 방법으로 As 조성비에 따른 에너지 전이점을 얻을 수 있었다. 또한 얻어진 에너지 전이점 값을 이용하여 linear augmented Slater-type orbital 방법으로 전자 밴드 구조 계산을 하였고, 이를 바탕으로 $E_0$, $E_1$, $E_2$ 전이점 지역의 여러 전이점 ($E_1$, $E_1+\Delta_1$, $E_0'$, $E_0'+\Delta_0'$, $E_2$, $E_2+\Delta_2$, $E_2'$, $E_2'+\Delta_2$, $E_1'$) 의 특성을 정확히 정의할 수 있었다. 또한 As 조성비가 증가하면서 $E_2$, $E_2+\Delta_2$, $E_2'$, $E_2'+\Delta_2$ 전이점들이 서로 교차 되는 것을 발견하였고, 저온에서만 관측이 가능하였던 InSb 의 두 saddle-point (${\Delta_5}^{cu}-{\Delta_5}^{vu}$, ${\Delta_5}^{cl}-{\Delta_5}^{vu}$)를 상온에서 찾아내었다. 타원 편광 분석법을 이용한 전이점 연구 및 물성 분석은 InAsSb alloy 의 광학적 데이터베이스를 확보하는 성과와 더불어 새로운 디바이스기술 및 광통신 산업에도 유용한 정보가 될 것이다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.205-205
• /
• 2013

테라헤르쯔(terahertz: THz)파는 0.1~10 THz 의 범위로 적외선과 방송파 사이에 광대역 주파수 스펙트럼을 차지하고 있으며 직진성, 투과성, 그리고 낮은 에너지 (meV)를 가지고 있어 비 파괴적이고 무해한 장점을 지니고 있다. Ti:sapphire laser와 같은 femto-pulse source 등이 많은 발전이 되어 현재 많은 연구와 발전이 이루어지고 있다. femto-pulse source를 이용한 THz 응용에서는 높은 저항, 큰 전자 이동도, 그리고 아주 짧은 전하수명의 기판을 요구하는데 저온에서 성장한 (low-temperature grown : LT) GaAs는 격자 내에 Gallium 자리에 Arsenic이 치환 하면서 AsGa antisite가 발생하여 전하수명을 짧아지는 것을 응용하여 가장 많이 이용되고 있다. 현재 THz 응용분야에서 보다 작고 가격경쟁력이 있는 광통신을 이용한 THz photomixer등이 활발히 연구 하고 있다. 광섬유 내에서 손실과 분산이 최소값을 가지는 부분이 1.55 ${\mu}m$ 부근이고 In0.53Ga0.47As 기판을 이용하였을 때 여기에 완벽하게 만족하게 된다. 하지만 LT-InGaAs 의 경우 AsGa antisite로 인하여 carrier lifetime은 짧아지지만 높은 n-type 전하밀도를 가지게 된다. 이때 Be을 doping하여 전하밀도를 보상하여 높은 저항을 유지해야 하는데 Be의 활성화를 위해서는 열처리를 필요로 한다. 하지만 열처리를 하면 carrier lifetime이 길어지기 때문에 carrier lifetime과 저항을 적절히 조율해야 한다. 이는 물질자체의 특성이기 때문에 InGaAs는 GaAs보다 낮은 amplitude와 짧은 cut-off frequency를 가진다. 본 연구에서는 보다 높은 저항을 얻기 위하여 molecular beam epitaxy를 이용하여 semi-insulating InP:Fe 기판위에 격자 정합된 InGaAs:Be/InAlAs multi quantum well (MQW)를 온도별 ($250{\sim}400^{\circ}C$), 주기별 (50~150)로 성장을 하였고 이때 InGaAs layer의 Be doping level은 $2{\times}1018\;cm^{-3}$, Ex-situ annealing은 $550^{\circ}C$에서 10분으로 고정 하였다. THz 발생 실험에서는 InGaAs/InAlAs MQW은 4000 pA로 1,000 pA를 가지는 InGaAs epilayer보다 4배 높은 전류 신호를 얻을 수 있었고 모든 샘플이 2 THz에서 cut-off frequency를 가지고 있었다. THz 검출 실험에서는 LT-InGaAs:Be epilayer LT-InGaAs:Be/InAlAs, HT-InGaAs/InAlAs 샘플이 각각 180, 9000, 12000 pA의 전류신호를 가지고 있었고 모든 샘플이 2 THz에서 cut-off frequency를 가지고 있었다. HT-InGaAs/InAlAs MQW를 이용한 검출실험에서는 InGaAs layer가 defect free이지만 LT-InGaAs:Be/ InAlAs MQW 보다 높은 전류 신호를 얻을 수 있었다. 이는 InAlAs layer가 저항만 높이는 것뿐만 아니라 carrier trapping layer로써의 역할도 하는 것으로 사료된다.

• Korean Journal of Materials Research
• /
• v.6 no.8
• /
• pp.833-840
• /
• 1996

Diamond thin films were deposited on p-type (100) Si wafers using MPECVD. Prior to deposition, ultrasonic striking was done to improve density of nucleation sites with dimond powder of 40~$60\mu$m size. Then diamond thin films were deposited at $^900{\circ}C$, 40Torr and 1000W microwave power using ${CH}_{4}$ and ${H}_{2}$ gases. The purity, the morphology and the microstructur'e and microdefects of diamond thin films were characterized by Raman spectroscopy, SEM and TEM, repectively. In Raman spectroscopy the peaks of non-diamond phase increased as ${CH}_{4}$, concentration increased. In SEM, the morphology of diamond thin films varied from crystalline to cauliflower as ${CH}_{4}$, concentration increased. As ${CH}_{4}$ con centration increased, the density of defects increased, with most defects being {III} twin. ${MTP}_{5}$, were formed with five (II]) planes. As these (Ill) Planes were twinned, ${MTP}_{5}$, represented five-fold symmetry. ]n the interfaces, defects in diamond thin films fanned out from small regions implying nucleation sites.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.710-714
• /
• 1998

Organic electroluminescence devices (ELD) with hetero-junction structure were fabricated utilizing poly(p-phenylne vinylene) (PPV) as emitting layer and electron transport layer (ETL). 2-(4-biphenyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD) was used as an electron transport agent. Copolymers with stilbene type comonomers, such as poly(styrene-co-PVTS), poly(styrene-co-MeO-PVTS) and poly(styrene-co-MeO-ST) were synthesized to be used as a matrix polymer to disperse electron transport agent (PBD). Among the hetero-junction EL devices fabricated with the above materials, the device with poly(styrene-co-PVTS) as matrix polymer for ETL gave the highest luminance ($120.7cd/m^2$, 13 V). EL devices made with poly(styrene-co-MeO-PVTS) or poly(styrene-co-MeO-ST) matrix exhibited lower luminance than the one with polystyrene matrix and the single layer EL (ITO/PPV/Mg) device.

• Korean journal of food and cookery science
• /
• v.17 no.2
• /
• pp.156-164
• /
• 2001

Four different oligosaccharides used to determine their effects on gelatinization and retrogradation of Backsulgies(BSG), Korean traditional rice cake, were cyclodextrin, isomaltooligosaccharide, fructooligosaccharide and maltotetrose, with 3 or 6%(w/w), based on the rice flour. From the Amylograph and blue value data, adding 6% cyclodextrin into the rice flour fastened the gelatinzation process, and delayed the retrogradation in stored BSG at 4$\^{C}$ for up to 3 days, probably due to its cyclic structure. Using rheometer, the hardness of freshly made BSG added with cyclodextrin was significantly lower than that of control BSG, and increased with storage time in all BSGs at refrigerated temperature. When using maltotetrose in rice flour, the hardness of BSG was also significantly low, but slightly higher than that of cyclodextrin. Hunter “L” value in BSG decreased with the addition of oligosaccharides, but the higher the level of oligosaccharide in BSG, the insignificant the Hunter “a”,“b” values of BSG. From the X-ray diffraction studies, the rice flour showed typical A pattern, and the crystallinities of all BSG gave amorphous V type. The highest peaks of X-ray patterns in BSG added with 6% cyclodextrin or maltotetrose were, however, lower than that of the control, meaning the less crystalline, retrograded starch in the former BSGs. Based on sensory evaluation, BSG added with all oligosacchrides were not significantly different in taste, flavor, chewiness, moistness and overall preferences, with slightly darker color with longer storage time, compared to the control BSG.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.9
• /
• pp.794-798
• /
• 1996

Solid solutions of the nonstoichiometric Dy1-xSrxCoO3-y system with the compositions of x=0.00, 0.25, 0.50, 0.75, and 1.00 have been synthesized by the solid state reaction at 1000 ℃ under atmospheric air pressure. The crystallographic structures of the solid solutions are analyzed by the powder X-ray diffraction patterns at room temperature. The analyses assign the compositions of x=0.00 and 0.25 to the orthorhombic system with space group of Pbnm/D2h16, the compositions of x=0.50 and 0.75 to the tetragonal system like a typical SrCoO2.86, and the composition of x=l.00 or SrCoO2.50 to the brownmillerite type system with space group of I**a. The reduced lattice volumes increase with x value due to the larger radius of Sr2+ ion than that of Dy3+ ion. The mole ratio of Co4+ ion to total Co ion with mixed valence state between Co3+ and Co4+ ions at B sites or τ value has been determined by an iodometric titration. All the samples except for the DyCoO3 compound show the mixed valnce state and thus the composition of x=0.50 has the maximum τ value in the system. The oxygen vacancies increasing with x value are randomly distributed over the crystal lattice except for the composition of x=l.00 which have the ordering of the oxygen vacancies. The nonstoichiometric chemical formulas of the Dy1-xSrxCo3+1-τCo4+τO3-(x-τ)/2 system are formulated from the x, τ, and y values. The electrical conductivity in the temperature range of 100 to 900 K increases with τ value linearly because of positive holes of the Co4+ ions in π* band as a conducting carrier. The activation energy of the x=0.50 as Ea=0.17 eV is minimum among other compouds. Broad and high order transition due to the overlap between σ* and π* bands broadened by the thermal activation is observed near 1000 K and shows a low temperature-semiconducting behavior. Magnetic properties following the Currie-Weiss law show the low to high spin transition in the cobaltate perovskite. Especially, the composition of x=0.75 presents weak ferromagnetic behavior due to the Co3+-O2--Co4+ indirect superexchange interaction.

• Korean Journal of Breeding Science
• /
• v.43 no.5
• /
• pp.457-463
• /
• 2011

Plant specific gene family, NAC (NAM, ATAF, and CUC) transcription factors have been characterized for their roles in plant growth, development, and stress tolerance. In this study, we isolated OsNAC69 gene and analyzed expression level by inoculation of bacterial leaf blight pathogen, Xanthomonas oryzae pv. oryzae (Xoo). NAC transcription factor family can be divided into five groups (I-V). On the basis of phylogenetic analysis, OsNAC69 was fall into group II. OsNAC69 was strongly induced 1 hr after infected with Xoo. To investigate its biological function in the rice, we constructed vector for overexpression in rice, and then generated transgenic rice lines. Gene expression of OsNAC69-overexpressed transgenic rice lines were analyzed by northern blot. Analysis of disease resistance to pathogen Xoo, nine OsNAC69-overexpressed transgenic rice lines showing high expression level of OsNAC69 were shown more resistant than wild type. These results suggest that OsNAC69 gene may play regulatory role during pathogen infection.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.491-499
• /
• 2019

Recently, there has been increasing demand for power quality in power supply devices. The IEC 61000-3-2 standard requires that the AC / DC power supply for lighting meet the specifications for the power factor (PF) and total waveform distortion (THD). In addition, advanced countries in Europe are regulating the ripple rate as 15 ~ 30% for the flicker phenomenon caused by the change in the amount of foot energy due to the change in current of the output terminal. Therefore, domestic standards and regulations are being updated. This study adopted the Flyback converter to satisfy the PFC standard, and has the circuit first and second insulation function. To reduce the low frequency ripple of the LED current, Flyback, Coupled Inductor, LC parallel resonance filter, LLC resonance filter, and Cuk were simulated by PSIM to mimic each LED driving circuit. A coupled LC resonant circuit with a coupled inductor on the primary side and LC resonance on the secondary side was also proposed for output side ripple reduction.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.1
• /
• pp.76-84
• /
• 2019

This study evaluated the microleakage of three restorative materials and three tricalcium silicate-based pulp capping agents. The restorative materials were composite resin (CR), resin-reinforced glass ionomer cement (RMGI), and traditional glass ionomer cement (GIC) and the pulp capping agents were TheraCal $LC^{(R)}$ (TLC), $Biodentine^{(R)}$ (BD), and $ProRoot^{(R)}$ white MTA (WMTA). Additionally, shear bond strengths between the pulp-capping agents and dentine were compared. Class V cavities were made in bovine incisors and classified into nine groups according to the type of pulp-capping agent and final restoration. After immersion in 0.5% fuchsin solution, each specimen was observed with a stereoscopic microscope to score microleakage level. The crowns of the bovine incisors were implanted into acrylic resin, cut horizontally, and divided into three groups. TLC, BD and WMTA blocks were applied on dentine, and the shear bond strengths were measured using a universal testing machine. The microleakage was lowest in TLC + GIC, TLC + RMGI, TLC + CR, and BD + GIC groups and highest in WMTA + RMGI and WMTA + CR groups. The shear bond strength of BD group was the highest and that of WMTA group was significantly lower than the others.