• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.1
• /
• pp.223-228
• /
• 2017

In this paper, we are proposing an optimal design of wideband pulsed type gamma-ray sensors. These sensors were manufactured based on the design results and after word electrical properties were analyzed. The sensor input parameters were derived on the basis of pulsed gamma-ray spectrum and time-dependent energy rate, and the output current which were derived on the basis of the sensor sensitivity control circuit. Pulsed gamma-ray sensors were designed using the TCAD simulators. The design results show that the optimal Epi layer thickness is 45um with the applied voltage 3.3V and the diameter is 2.0mm. The doping concentrations are as follows : N-type is an Arsenic as $1{\times}10^{19}/cm^3$, P-type is a Boron as $1{\times}10^{19}/cm^3$ and Epi layer is Phosphorus as $3.4{\times}10^{12}/cm^3$. The fabricated sensor was a leakage current, 12pA at voltage -3.3V and fully depleted mode at voltage -5V. A test result of pulsed radiation shows that the sensor gives out the optimal photocurrent.

• Journal of Sensor Science and Technology
• /
• v.27 no.4
• /
• pp.232-236
• /
• 2018

A radiation detection sensor was developed and characterized by combining three types of CsI(Tl) scintillators and an array-type SiPM to detect the radioactive contamination of discharged water in real time. The characterization results showed that type 3 exhibited the most desirable characteristics in response linearity (R-square: 0.97889) according to detection sensitivity and incident radiation dose. Furthermore, in terms of spectral characteristics, type 3 exhibited 16.54% at 0.356 MeV (the emission gamma ray energy of $^{133}Ba$), 10.28% at 0.511 MeV (the emission gamma ray energy of $^{22}Na$), 9.68% at 0.356 MeV (the emission gamma ray energy of $^{137}Cs$), and 2.55% and 4.80% at 1.173 MeV and 1.332 MeV (the emission gamma ray energies of $^{60}Co$), respectively. These measurements confirmed the good energy characteristics. The results were used to evaluate the spectral characteristics and energy linearity in a mixed source using type 3 with the best detection characteristics. It was confirmed that the gamma ray peaks of $^{133}Ba$, $^{22}Na$, $^{137}Cs$, and $^{60}Co$ were well resolved. Moreover, it was confirmed that R-square, which is an indicator of energy linearity, was 0.99986. This indicates a good linearity characteristic. Based on this study, further commercialization studies will contribute to measurements in real time and to the management of the contamination caused by radioactive wastewater or radioactive material leakage, which originate from facilities that use radioactive isotopes or care facilities.

• Journal of Magnetics
• /
• v.6 no.4
• /
• pp.122-125
• /
• 2001

Phase relationships of the HDDR (hydrogenation, disproportionation, desorption and recombination)-treated Sm$_3$(Fe,M)$_{29}$-type alloy with chemical composition of Sm$_{9}$Fe$_{65}$ $Co_{20}$V$_{6}$ were studied by X-ray diffraction (XRD) and by thermomagnetic analysis (TMA). The alloy was disproportionated into a mixture of $SmH_{x}$ and $\alpha$-Fe at high temperature under hydrogen gas. The disproportionated material was recombined into a mixture of Sm-(Fe,M) (M = Co and/or V) and $\alpha$-Fe phases. The structure of the Sm-(Fe,M) phase was dependent upon the recombination conditions, and a detailed phase diagram showing the phase relationships in the HDDR-treated alloy has been established. The Sm-(Fe,M) phase in material recombined above $900^{\circ}C$ had the $Sm_2Fe_{17}$-type structure, and it exhibited the $SmFe_{7}$-type structure when recombined at temperatures ranging from $700^{\circ}C$ to $850^{\circ}C$. Recombination below $650^{\circ}C$ led to the $SmFe_3$-type structure of the Sm-(Fe,M) phase. Curie temperatures of the Sm-(Fe,M) phases in the recombined material were significantly higher than those of the corresponding stoichiometric phases. It was suggested that the chemical composition of the Sm-(Fe,M) phases may be significantly different from that of the corresponding stoichiometric phases. All the HDDR-treated $Sm_{9}Fe_{65}Co_{20}V_{6}$ materials showed the soft magnetic features regardless of the phase constitution.n.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10c
• /
• pp.42-47
• /
• 1998

Experimental investigation was undertaken to determine early-age strength development and the relationships between the mechanical properties of type I, V and V/fly ash cement concrete with different curing temperature. The tests for mechanical properties, i.e., compressive strength, splitting tensile strength and modulus of elasticity were carried out for type, I, V and V with 15% replacement with fly ash cement concrete. For this purpose 480 concrete cylinders cured at isothermal conditions of 10, 23, 35 and 5$0^{\circ}C$ were tested at ages of 1, 3, 7 and 28days. According to the experiments, the concrete subjected to high temperature at early age got greater strength at early age, however eventually lower strength at late age. The derived relationships between compressive strength and splitting tensile strength and elastic modulus of elasticity appeared to be identical for all types of cement.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.749-751
• /
• 1998

In this study, the wind-mill type ultrasonic motor was fabricated, and then revolution and temperature characteristics of the ultrasonic motor were measured. Brass metal was pressed with umbrella-type using metal mold, then slot of 4 kind was processed in each of thickness. Among sixteen's ultrasonic motors, heat loss on applied voltage was much at stator of the highest resonant point, but heat loss on applied voltage was almost neglected at the lowest resonant point of stator. The thickener thickness of elastic body, revolution speed was decreased. The more slot of elastic body, revolution speed was increased. Applied voltage was changed from $10V_{max}$ to $100V_{max}$. When applied voltage was under $20V_{max}$, ultrasonic motor was not rotated. When applied voltage was over $90V_{max}$, revolution of ultrasonic motor was saturated. Maximum revolution speed was 510[rpm].

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.46-47
• /
• 2006

본 논문은 CD형 초전도 케이블을 22.9kV 다중접지 배전계통에 적용한 경우 불평형 지락 고장이 초전도 케이블에 미치는 영향을 검토하고 이로 인한 중성선 전류의 변화 및 계통보호를 위한 대책을 논한다. 3상 CD형 초전도 케이블을 사용하는 경우 귀로선은 전향선과 전류가 반대이면서 거의 동일한 전류가 흐르므로 회로의 인덕턴스를 크게 줄일 수 있지만 이를 위해 회로를 단락하여 운전하는 경우 지락고장시 영상회로가 별도로 존재하지 않으면 지락전류를 저감시키는 결과를 초래하게 되어 계통보호에 영향을 주게 된다. 본 논문은 EMTDC 프로그램을 활용하여 이 현상을 XLPE 케이블 계통과 비교, 모의하는 한편, 정상적인 보호계전기 동작이 가능토록 하는 대책에 대해 논한다.

• Kyungpook Mathematical Journal
• /
• v.50 no.1
• /
• pp.89-100
• /
• 2010

Let g = (V, E, ${\mu}$) be a weighted directed tree, where V is a vertex set, E is an edge set, and ${\mu}$ is ${\sigma}$-finite measure on V. The tree g induces a composition operator C on the Hilbert space $l^2$(V). Hand-type directed trees are defined and characterized the weak hyponormalities of such C in this note. Also some additional related properties are discussed. In addition, some examples related to directed hand-type trees are provided to separate classes of weak-hyponormal operators.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.1-10
• /
• 1998

A GaAs MMIC composed of VCO (voltage controlled oscillator) and mixer for PCS receiver has been developed using 1.mu.m ion implanted GaAs MESFET process. The VCO consists of a colpitts-type oscillator with a dielectric resonator and the circuit configuration of the mixer is a dual-gate type with an asymmetric combination of LO and RF FETs for the improvement of intermodulation characteristics. The common-source self-biasing is used in all circuits including a buffer amplifier and mixer, achieving a single power supply (3V) operation. The total power dissipation is 78mW. The VCO chip shows a phase noise of-99 dBc/Hz at 100KHz offset. The combined VCO/mixer chip shows a flat conversion gain of 2dB, the frequency-tuning factor of 80MHz/volts in the varacter bias ranging from 0.5V to 0.5V , and output IP3 of dBm at varactor bias of 0V. The fabricated chip size is 2.5mm X 1.4mm.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.40-47
• /
• 1998

This paper report sthe design, fabrication and characterization of an AlGaAs/GaAs HBT (heterojunction bipolar transistor) with an air-bridge isolation structure which is made to improve high frequency characteristics for the application to the mobile communication system in the next genration. We found that the size, shape and structure of HBT have an effect on the high frequency operation. The measured dc and ac characteristics of the four type HBTs were compared and analyzed. An E-type HBT with an air-bridge structure by undercut etching exhibited .beta.=56, $V_{off-set}$ = 0.3 V, B $V_{CEO}$=7.0V with $f_{T}$=40 GHz and $f_{max}$=45GHz at a collector current density of 7.1*10$^{4}$ A/c $m^{2}$.>.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.524-526
• /
• 2004

We perform intelligent substation construction of 154kV class with KEPRI. The intelligent substation is build in Gochang 765kV testing facility and consists of electronic instruments, digital control panel, remote monitoring and diagnosis system, and digital relay system. Rogowski coil type CT(RCT) and capacitive voltage divider(CVD) are applicable for instrument transformer of conventional type. Digital control panel(UP) replaces local panel which is drived by mechanical operation. For monitoring condition of GIS and TR, various sensors are used. In this paper, we report the synopsis and the progress state of project.