• Journal of the Korean Geotechnical Society
• /
• v.31 no.3
• /
• pp.51-62
• /
• 2015

Shear behavior obtained by direct shear tests is dependent on shear box and boundary condition. The objective of this study is to analyze problems of conventional direct shear test (type-A) and provide the reliable results by developing type-C direct shear apparatus. Experimental tests are carried out for Ulleung sand by using type-A and -C direct shear devices. The soil specimens, which are prepared at the relative density of 60%, and are applied to vertical confining stresses of 50, 100, 200, 300, and 400 kPa, are sheared at a constant shear strain rate of 0.5 mm/min. By comparing the results obtained by type-A and -C direct shear apparatus under constant normal load (CNL) condition, the performance of new one is verified. In addition, two constrained conditions including constant normal load (CNL) and constant pressure (CP) are applied to type-C one. Experimental results show that type-A direct shear apparatus has some problems such as rotating of loading plate and upper shear box, and the frictional forces between soil and inner wall of upper shear box. Thus, the shear strengths obtained by type-A device are overestimated or underestimated depending on shear box and boundary condition. On the other hand, type-C device produces clear and consistent test results regardless of constrained conditions. This study represents that type-C direct shear apparatus not only can solve the problems of type-A direct shear apparatus but provide the reliable results.

• Korean Journal of Soil Science and Fertilizer
• /
• v.37 no.6
• /
• pp.365-370
• /
• 2004

To invesligate the characteristics of silica sorption on soils silica sorption experiments were conducted with 9 soils at 4 pH levels (5, 6, 7, and 8). Silica sorption increased in great extent with increase of pH. At the same pH level silica sorption increased linearly with increase of equilibrium $SiO_2$ concentration. Silica sorption characteristics was C-type. The C-type slope, i.e., the slope of linear regression of silica sorption isotherm, increased exponentially with increase of pH in all soils. Log(C-type slope) increased linearly with increase of pH in all soils. The slopes of linear regression were similar in most soils from 0.29 to 0.34 except Sachon and Jonggog soil. None of the soil properties showed any correlation with the slope of linear regression of Log(C-type slope) to pH. Only $Fe_o$ (oxalate extractable Fe oxides) was significantly correlated with the Log(C-type slope) at pH 7 in simple correlation analysis, and was shown to be the principal contributor as determined by standardized multiple linear regression.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1524-1526
• /
• 2002

본 논문에서는 $1.62{\times}1.0{\times}0.88mm^3$ 크기의 C-type과 $1.58{\times}0.82{\times}0.94mm^3$ 크기의 H-type RF 칩 인덕터를 제작하고 그들의 고주파 특성을 비교하였다. 본 연구에서는 저손실 $Al_2O_3$ 코아 물질과 직경 $40{\mu}m$의 구리(Cu) 코일을 사용하였다. 권선수를 $2{\sim}14$회로 하여 인덕턴스(L), 품질계수(Q), 임피던스의 크기와 위상, 커패시턴스(C)를 HP4291B Impedance/Material Analyzer로 측정하였다. 10회 권선시 C-type은 55nH, H-type은 67nH, 14회 권선시 C-type은 100nH, H-type은 122nH 정도로 측정되었다. 실험 결과 H-type이 C-type보다 동일 권선수에 대하여 높은 인덕턴스와 높은 자기공진주파수(SRF)를 나타냄을 확인하였다. 또한 최대 품질계수는 두 형태가 거의 비슷한 값($55{\sim}87$)을 가짐을 관찰하였다. 따라서 H-type이 C-type보다 우수한 성질을 나타냄을 알 수 있다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.2
• /
• pp.125-132
• /
• 2010

The authors have investigated the acoustic field analysis using the Constrained Interpolation Profile(CIP) Method recently proposed by Yabe. This study has examined the calculation accuracy of the three-dimensional(3-D) acoustic field analysis using the type C CIP method. In this paper we show phase error of type C CIP method and the dependence on the wave-propagation direction in the type C CIP acoustic field analysis, and then demonstrate that it gives less-diffusive results than conventional analysis. Moreover, in comparison between type C-1 CIP, type C-2 CIP, type M CIP and FDTD, reports the memory requirements and calculation time of each method.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.3
• /
• pp.66-72
• /
• 1995

The rate of fixation of the components were evaluated in CCA-Type B and CCFZ-treated radiata pine sapwood by quantitative analysis of solution expressed from the treated wood. The leaching characteristics of radiata pine blocks treated with CCA-Type B and CCFZ were also evaluated by the AWPA standard leaching test. Both fixation and leaching charactersistics of CCA-Type B were compared with CCA-Type C treated wood samples. The rate of CCA-Type B fixation was a little faster than that of CCFZ. However, significant amounts of arsenic was unfixed in the CCA-Type B treated samples and consequently leached. These significant quantities of arsenic liberated from the CCA-Type B treated wood during service may pose some environmental concerns. Arsenic was no longer detectable from CCA-Type C treated samples when fixation was complete, even though the fixation of CCA-Type C was slower in some degree than CCA-Type B. In summary, it could be said that CCFZ was much safer preservative than CCA-Type B by the criterion based on the relative hazard assessed by absolute amount of unfixed element present in the treated wood. Also the decision that CCA preservative has to move from Type B to Type C should be made sooner or later for continuous use of CCA preservative in the future.

• Journal of Fashion Business
• /
• v.6 no.4
• /
• pp.151-162
• /
• 2002

This study aims to reveal the effects of shoe size room on the inner environment of shoes by examining the changes of footskin temperature, temperature and humidity of the shoes, and psychological responses. The following conclusions were made: 1. Skin temperature had significant differences according to shoe sizes in the inner foot parts (right/left) and the outer foot part (left). As time went, skin temperature was distributed as follows: Type A > Type C > Type B. 2. Skin temperature appeared in the following order: instep > inner foot > outer foot. 3. The temperature within the shoes had significant differences: Type A > Type C > Type B. But no significance was recognized in the humidity within the shoes: Type B > Type C > Type A. 4. Some significance was noticed in the psychological responses of size fitness and comfortableness. In size fitness, Type B was responded to be fitting, Type A little small, and Type C rather big. Moisture had similar changes according to three shoe sizes, but humid was the response as time went. Comfortableness appeared in the order of Type C > Type B > Type A.

• Annals of Surgical Treatment and Research
• /
• v.95 no.5
• /
• pp.249-257
• /
• 2018

Purpose: Multidrug resistance-associated protein (MRP) 2 is a glutathione conjugate in the canalicular membrane of hepatocytes. Early graft damage after liver transplantation (LT) can result in alteration of MRP2 expression. The purpose of this study was to evaluate the relationship between the pattern of MRP2 alteration and graft outcome. Methods: Forty-one paraffin-embedded liver graft tissues obtained by protocol biopsy within 2 months after LT; these were stained using monoclonal antibodies of MRP2. We selected 15 live donor biopsy samples as a control, that showed homogenous canalicular staining for MRP2. The pattern of canalicular MRP2 staining of graft was classified into 3 types: homogenous (type C0), focal (type C1), and no (type C2,) staining of the canaliculi. Results: In total, 17.1% graft tissues were type C0, 36.6% were type C1, and 46.3% were type C2. The median operation time was longer in patients with type C2 (562.6 minutes) than in patients with type C0 (393.8 minutes) (P = 0.038). The rates of posttransplant complications were higher in patients with type C2 (100%) than in patients with type C0 (42.9%) and C1 (73.3%) (P < 0.001). Conclusion: MRP2 expression pattern was altered in 82.9% after LT. The pattern of MRP2 alteration was associated with longer operation time and higher rates of post-LT complications.

• Carbon letters
• /
• v.1 no.3_4
• /
• pp.165-169
• /
• 2001

The C-type mesophase pitch-based carbon fiber (C-MPCF) was prepared throuch C-type spinnerette and compared the mechanical properties to those of round type mesophase pitch fiber (R-MPCF) and C-type isotropic pitch fiber (C-iPCF). The tensile strength and modulus of C-MPCF were about 18.6% and 35.7% higher than those of R-MPCF. The tensile strength of C-MPCF was 62% higher than that of C-iPCF of the same $8{\mu}m$ thickness because of more linear transverse texture, which could be easily converted to graphitic crystallinity during heat treatment. The torsional rigidity of C-MPCF was 2.37 times higher than that of R-MPCF. The electrical resistivity of C-MPCF was $8{\mu}{\Omega}{\cdot}m$. The C-iPCF shows far lower electrical resistivity than R-iPCF as well as the mesophase carbon fiber because of better alignment of texture to the fiber axis.

• Journal of Sensor Science and Technology
• /
• v.16 no.4
• /
• pp.259-262
• /
• 2007

This paper describes the electrical characteristics of polycrystalline (poly) 3C-SiC thin film diodes, in which poly 3C-SiC thin films on n-type and p-type Si wafers, respectively, were deposited by APCVD using HMDS, $H_{2}$, and Ar gas at $1150^{\circ}C$ for 3 hr. The schottky diode with Au/poly 3C-SiC/Si (n-type) structure was fabricated. Its threshold voltage ($V_{bi}$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_{D}$) value were measured as 0.84 V, over 140 V, 61 nm, and $2.7{\times}10^{19}cm^{-3}$, respectively. Moreover, for the good ohmic contact, Al/poly 3C-SiC/Si (n-type) structure was annealed at 300, 400, and $500^{\circ}C$, respectively for 30 min under the vacuum condition of $5.0{\times}10^{-6}$ Torr. Finally, the p-n junction diodes fabricated on the poly 3C-Si/Si (p-type) were obtained like characteristics of single 3CSiC p-n junction diode. Therefore, poly 3C-SiC thin film diodes will be suitable for microsensors in conjunction with Si fabrication technology.

• The korean journal of orthodontics
• /
• v.37 no.1 s.120
• /
• pp.5-15
• /
• 2007

Objective: The purpose of this study was to evaluate the mechanical performance of mini-screws during insertion into artificial bone with use of the driving torque tester (Biomaterials Korea, Seoul, Korea), as well as testing of Pull-out Strength (POS). Methods: Experimental bone blocks with different cortical bone thickness were used as specimens. Three modules of commercially available drill-free type mini-screws (Type A; pure cylindrical type, Biomaterials Korea, Seoul, Korea, Type B; partially cylindrical type, Jeil Medical, Seoul, Korea, Type C; combination type of cylindrical and tapered portions, Ortholution, Seoul, Korea), were used. Results: Difference in the cortical bone thickness had little effect on the maximum insertion torque (MIT) in Type A mini-screws. But in Type B and C, MIT increased as the cortical bone thickness Increased. MIT of Type C was highest in all situations, then Type B and Type A in order. Type C showed lower POS than Type A or B in all situations. There were statistically significant correlations between cortical bone thickness and MIT, and POS for each type of the mini-screws. Conclusion: Since different screw designs showed different insertion torques with increases in cortical bone thickness, the best suitable screw design should be selected according to the different cortical thicknesses at the implant sites.