• 한국전기전자재료학회논문지
• /
• 제13권2호
• /
• pp.95-100
• /
• 2000

For the well-controlled growing in-situ heavily phosphorus doped polycrystalline Si films directly on Si wafer by reduced pressure chemical vapor deposition, a study is made of the two step growth. When in-situ heavily phosphorus doped Si films were deposited directly on Si (100) wafer, crystal structure in the film is not unique, that is, the single crystal to polycrystalline phase transition occurs at a certain thickness. However, the well-controlled polycrtstalline Si films deposited by two step growth grew directly on Si wafers. Moreover, the two step growth, which employs crystallization of grew directly on Si wafers. Moreover, the two step growth which employs crystallization of amorphous silicon layer grown at low temperature, reveals crucial advantages in manipulating polycrystal structures of in-situ phosphorous doped silicon.

• 한국재료학회지
• /
• 제28권4호
• /
• pp.235-240
• /
• 2018

We propose a speedy two-step deposit process to form an Au electrode on hole transport layer(HTL) without any damage using a general thermal evaporator in a perovskite solar cell(PSC). An Au electrode with a thickness of 70 nm was prepared with one-step and two-step processes using a general thermal evaporator with a 30 cm source-substrate distance and $6.0{\times}10^{-6}$ torr vacuum. The one-step process deposits the Au film with the desirable thickness through a source power of 60 and 100 W at a time. The two-step process deposits a 7 nm-thick buffer layer with source power of 60, 70, and 80 W, and then deposits the remaining film thickness at higher source power of 80, 90, and 100 W. The photovoltaic properties and microstructure of these PSC devices with a glass/FTO/$TiO_2$/perovskite/HTL/Au electrode were measured by a solar simulator and field emission scanning electron microscope. The one-step process showed a low depo-temperature of $88.5^{\circ}C$ with a long deposition time of 90 minutes at 60 W. It showed a high depo-temperature of $135.4^{\circ}C$ with a short deposition time of 8 minutes at 100 W. All the samples showed an ECE lower than 2.8 % due to damage on the HTL. The two-step process offered an ECE higher than 6.25 % without HTL damage through a deposition temperature lower than $88^{\circ}C$ and a short deposition time within 20 minutes in general. Therefore, the proposed two-step process is favorable to produce an Au electrode layer for the PSC device with a general thermal evaporator.

• 한국결정성장학회지
• /
• 제12권6호
• /
• pp.311-316
• /
• 2002

2-step 증착법과 Bias-Enhanced Nucleation(BEN)법을 이용해 다결정 Ni 기판에 고품질의 다이아몬드 박막 합성을 연구하였다. $810^{\circ}C$에서 1시간 증착하여 soot충을 형성시킨 후 기판온도를 soot층의 형성이 억제되는 온도인 $925^{\circ}C$로 올려 5시간 증착하는 2-step법을 통해 고품질의 다이아몬드를 합성할 수 있었다. 또한, $925^{\circ}C$에서 -220V의 bias를 10분 동안 기판에 인가한 후 2시간 동안 증착하는 BEN법을 이용해 양질의 다이아몬드를 합성할 수 있었다. $925^{\circ}C$에서 bias 처리를 하지 않은 경우에는 10시간 동안 증착을 시도한 후에도 다이아몬드가 생성되지 않았다.

• 한국전기전자재료학회논문지
• /
• 제16권3호
• /
• pp.190-194
• /
• 2003

Dielectric thin films of (P $b_{0.72}$,L $a_{0.28}$) $Ti_{0.93}$ $O_3$ (PLT(28)) have been deposited on Pt(111)/Ti/ $SiO_2$/Si(100) substrates in-situ by pulsed laser deposition using different annealing and deposition Processes. We have investigated the effect of hydrogen annealing on the ferroelectric properties of PLT thin films and found that the annealing process causes the diffusion of hydrogen into the ferroelectric film resulting in the destruction of polarization. We have tried to form the film by a two-step deposition process In order to improve electrical property. Two-step process to grow PLT films was adopted and verified to be useful to enlarge the grain size of the film and to reduce the leakage current characteristics. Structural properties and electrical properties including dielectric constant, ferroelectric characteristics, and leakage current of PLT thin films were shown to be strongly influenced by grain size. The film deposited by using two-step Process including pre-annealing treatment has a strongly(111) orientation. However, the films deposited by using single -step process with hydrogen annealing process show the smallest grain size. The film deposited by using two-step process including pre-annealing treatment shows the leakage current density of below 10$^{-7}$ A/c $m^2$ for the field of smaller than 100 kV/cm. However, the films deposited by using single-step process with hydrogen annealing process and pre-annealing process show worse leakage current density than the film deposited by using two-step process including pre-annealing treatment.tment.

• 한국대기환경학회지
• /
• 제16권5호
• /
• pp.445-451
• /
• 2000

To estimate dry deposition flux of 12 elements in aerosols, aerosol particles were sampled by a low-pressure impactor(LPI) and a dust jar. The concentrations of 12 elements in aerosol particle and dry deposition were analyzed by a PIXE analysis using as a 2.0 MeV-proton beam. The mean dry deposition velocities of 12 elements were estimated by ranges of 0.74∼2.62 cm/sec. The results showed that the highest value was 3.26 cm/sec for Ca and the lowest value 0.74 cm/sec for Fe. The dry deposition flux for elements was calculated as a function of particle size by 1-step method and 12-step method. In this work, dry deposition velocities were computed with the two existing models; the coarse-particle fraction(4∼30 mm diameter) using the dry deposition velocity model of the Noll and Fang(1998) and the fine-particle fraction (0.05∼4mm diameter) using the Shemel and Hodgson(1980) model. The ratios of the mean calculated/measured fluxes were 3.59 for 1-step method and 0.60 for 12-step method respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1340-1342
• /
• 2001

ZnO thin films are Prepared on Si(111) substrate by RF magnetron sputtering. Two-step deposition method is proposed to obtain ZnO thin films with high c-axis (002) TC value and electrical resistivity. This method consists of the following two-step deposition procedures: 1st-deposition for 10$\sim$30 min without oxygen at 100W and 2nd-deposition with oxygen added in the range of $O_2/(Ar+O_2)$ = 10 $\sim$ 50%. SAW filters with IDT/ZnO/Si(111) configuration are also fabricated. From the frequency response characteristics, the insertion loss and the side-lobe rejection are estimated.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제3C권2호
• /
• pp.43-47
• /
• 2003

Lead zirconate titanate (PZT) thin films were fabricated by the pulsed laser ablation deposition (PLAD) method onto Pt/Ti/SiO$_2$/Si substrates. Crystalline phases as well as preferred orientations in PZT films were investigated by X-ray diffraction analysis (XRD). The well-crystallized perovskite phase and the (101) preferred orientation were obtained by two-step annealing at the conditions of $650^{\circ}C$, 1 hour. It was found that the temperature for the pulsed laser ablated PZT films annealed via a two-step annealing process can be reduced 20$0^{\circ}C$ compared to that of the conventional three-step annealing temperature profile for enhancing the transformation of the perovskite phase. The remanent polarization and the coercive field of this film were about 20 $\mu$C/$\textrm{cm}^2$ and 46 kV/cm, while the dielectric constant and loss values measured at 1 KHz were approximately 860 and 0.04, respectively. The interesting phenomena of this film, such as vertical shift in hysteresis curve, are also discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.395-397
• /
• 2002

Dielectric thin films of Pb$\_$0.72/La$\_$0.28/Ti$\_$0.93/O$_3$(PLT(28)) have been deposited on Pt(111)/Ti/SiO$_2$/Si(100) substrates in-situ by pulsed laser deposition using different annealing and deposition processes. We have investigated the effect of hydrogen annealing on the ferroelectric properties of PLT thin films and found that the annealing process causes the diffusion of hydrogen into the ferroelectric film resulting in the destruction of polarization. Two-step process to grow PLT films was adopted and verified to be useful to enlarge the grain size of the film. Structural properties including dielectric constant, and ferroelectric characteristics of PLT thin films were shown to be strongly influenced by grain size. The film deposited by using two-step process including pre-annealing treatment has a strong (111) orientation. However, the films deposited by using single-step process with hydrogen annealing process shows the smallest grain size.

• 한국생산제조학회지
• /
• 제25권1호
• /
• pp.36-41
• /
• 2016

A method is proposed for the improvement of deposition reproducibility in the selective electrodeposition process using laser masking and DC voltage. Selective electrodeposition using laser masking and DC voltage can achieve a deposited layer with micro patterns. However, selective electrodeposition using laser masking and DC voltage have a critical problem: the lack of reproducibility in selective deposition. The reproducibility of selective electrodeposition can be improved by a new process that consists of laser masking, two-step electro-deposition, laser scribing, and ultrasonic cleaning. The experiments in this study show that the reproducibility of selective deposition can be successfully improved by the combination of two-step electrodeposition and laser scribing.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.3-5
• /
• 2001

ZnO thin films are deposited on $SiO_2$/Si (111) substrate by RF magnetron sputtering. The two-step deposition method is proposed to enhance both the c-axis orientation and the resistivity of ZnO films. This method consists of the following two procedures: the 1 st-deposition for 30 min without oxygen at l00W and the 2nd-deposition with oxygen added in the range of $O_2/(Ar+O_2)=10{\sim}50%$. Effects of thermal treatment on the properties of ZnO films are systematically investigated.