• Journal of Biosystems Engineering
• /
• 제20권3호
• /
• pp.275-287
• /
• 1995

The rice processing complex(RPC) consisted of the rice handling, drying, storage, and milling processes. It has been established at 83 locations domestically by April 1994, and 200 of RPC will be built more throughout the country. Therefore, this study has been performed to achieve two objectives as the followings : 1) Development of mathematical models which can assess the requirement of electricity, fuel, and labor for four model systems of rice processing complex. 2) Development of a computer simulation model which produce the improved designs of RPC by the evaluation results of energy requirements of four RPC models. The results from this study are summarized as follows : 1) Mathematical models were developed on the basis of result of mass balance analysis and required power of machines for each process. 2) A computer simulation model was developed, which can produce the improved designs of RPC by the evaluation results of energy requirements. The computer simulation model language was BORLAND $C^{++}$. 3) The results of simulation showed that total energy requirements were ranged from 75.94㎾h/t to 124.30㎾h/t. 4) From the results of computer analysis of energy requirement classified by drying type, it was found that energy requirement of the drying type A{paddy rice (PR) for storage-natural air drying(15%), PR for milling-heated air drying(16%)} were less than that of the drying type B{1 step-natural air drying(PR for storage : 18%, PR for milling : 20%), 2 step-heated air drying(PR for storage : 15%, PR for milling : 16%)}. 5) The energy efficient drying method is that all the incoming rough rice to RPC should be dried by national air drying systems. If it is more than the capacity of national air drying system, the amount of surplus rough rice is recommended to be dried by the heated air drying method.

• 한국분말재료학회지
• /
• 제17권3호
• /
• pp.235-241
• /
• 2010

Mo nanopowder was synthesized by ball-milling and subsequent hydrogen-reduction of $MoO_3$ powder. To fabricate ultra fine grained molybdenum, two-step sintering and spark plasma sintering process were employed. The grain size of specimen by two-step sintering and spark plasma sintering was around $0.6\;{\mu}m$ and $0.4\;{\mu}m$, respectively. Mechanical properties of ultra fine grained Mo with relative density of above 90% were significantly improved at room and high temperatures comparing to commercial bulk Mo of 99% relative density. This result was mainly explained by the grain size refinement due to diffusion-controlled sintering.

• 한국분말재료학회지
• /
• 제17권2호
• /
• pp.136-141
• /
• 2010

Bismuth-telluride based $(Bi_{0.2}Sb_{0.8})_2Te_3$ thermoelectric powders were fabricated by two-step planetary milling process which produces bimodal size distribution ranging $400\;nm\;{\sim}\;2\;{\mu}m$. The powders were reduced in hydrogen atmosphere to minimize oxygen contents which cause degradation of thermoelectric performance by decreasing electrical conductivity. Oxygen contents were decreased from 0.48% to 0.25% by the reduction process. In this study, both the as-synthesized and the reduced powders were consolidated by the spark plasma sintering process at $350^{\circ}C$ for 10 min at the heating rate of $100^{\circ}C/min$ and then their thermoelectric properties were investigated. The sintered samples using the reduced p-type thermoelectric powders show 15% lower specific electrical resistivity ($0.8\;m{\Omega}{\cdot}cm$) than those of the as-synthesized powders while Seebeck coefficient and thermal conductivity do not change a lot. The results confirmed that ZT value of thermoelectric performance at room temperature was improved by 15% due to high electric conductivity caused by the controlled oxygen contents present at bismuth telluride materials.

• 한국재료학회지
• /
• 제9권1호
• /
• pp.86-91
• /
• 1999

(001) $\textrm{SrTiO}_3$(STO) 기판위에 고온초전도 $\textrm{YBa}_{2}\textrm{Cu}_{3}\textrm{O}_{7-x}$(YBCO)박막을 이용한 계단형 모서리 임계접합을 제조하였다. STO (100) 단결정 기판위에 계단형 모서리(step-edge)를 제작하기 위한 이온밀링 마스크로 plasma enhanced chemical vapor deposition방법으로 증착된 diamond-like carbon (DLC) 박막을 사용하였고, oxygen reactive ion etch 방법으로 건식식각하였다. 이렇게 제작된 계단형 모서리 기판위에 c-축 수직한 YBCO 박막과 STO박막을 pulsed laser deposition방법으로 에피텍셜하게 증착하였다. 계단의 상층과 하층에서 모두 임계가 형성되었으며 이 접합의 임계온도는 77 K 이상이었고 16K에서 $\textrm{I}_{c}\textrm{R}_{n}$products가 7.5mV, 77 K에서 0.3mV의 값을 나타내었다. 이들 전류-전압 특성은 two noisy resistively shunted Josephson junction 모델을 잘 만족하였다.

• 한국분말재료학회지
• /
• 제29권6호
• /
• pp.492-498
• /
• 2022

N-doped Na₂Ti₆O₁₃@TiO₂ (denoted as N-NTO@TiO₂) composites are successfully synthesized using a simple two-step process: 1) ball-milling of TiO₂ with Na₂CO₃ followed by heat treatment at 900℃; 2) mixing of the prepared Na₂Ti₆O₁₃ with titanium isopropoxide and calcining with urea at 500℃. The prepared composites are characterized using XRD, SEM, TEM, FTIR, and BET. The N-NTO@TiO₂ composites exhibit well-defined crystalline and anatase TiO₂ with exposed {101} facets on the external surface. Moreover, dopant N atoms are uniformly distributed over a relatively large area in the lattice of the composites. Under visible light irradiation, ~51% of the aqueous methylene blue is photodegraded by N-NTO@TiO₂ composites, which is higher than the values shown by other samples because of the coupling effects of the hybridization of NTO and TiO₂, N-doping, and presence of anatase TiO₂ with exposed {101} facets.