• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.139-142
• /
• 2006

This paper describes a new method using random modulated strategies for switched reluctance machines. The proposed method is combined random turn-on, turn-off angle technique and random pulse width modulation technique. The purpose of this proposed method is to decrease harmonic spectrum, and thus reduce the emitted acoustical noise. A random generator is generated by linear congruential generator (LCG) using random pulse position (RPP) scheme. Simulation results show that the harmonic intensity of proposed method is better than that of conventional method.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.57-64
• /
• 2002

This paper describes the results of a series of experiments executed by using two pilot-scale oxv-fuel burners are designed for maximum capacity of 50,000 kacl/hr, 300,000 kcal/hr and installed in the test furnace. The effects of turn-down ratio, excess oxygen ratio, nozzle exit velocity, injection angle, swirl vane angle and inlet oxygen temperature on the combustion characteristic are investigated. Temperature distributions are measured using R-type and Molybdenum sheathed C-type thermocouple. The results showed that maximum temperature and mean temperature increase with the increase of turn-down ratio and inlet oxygen temperature. The maximum flame temperature was increased about 35% compared to the case of equivalent air operated condition. In addition, Optimum excess oxygen ratio and nozzle characteristics are obtained for this oxy-fuel glass melting furnace.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.239-243
• /
• 2004

This paper presents a proper switching angle calculation method of Switched Reluctance Motor (SRM) for drill. The characteristic of SRM drive is very related to the scheduling of commutation angle and current waveforms. Therefore, a selection method of switching turn-on and turn-off angle is suggested for adaptational operation of SRM with varied rotor speed and load. Simulation and experimental results are presented for the validation of proposed method.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.4
• /
• pp.67-76
• /
• 2008

The purpose of this study was to analyze differences in kinematic variables for mogul short turn motion between superior and inferior group, so that it can explore more effective mogul short turn motions. To meet the goals, this study selected total 10 ski players who would participate in mogul short turn event of the National Technical Ski Championship 2007, so that it could analyze kinematic variables by way of 3D motion analysis using DLT method. As a result, this study came to the following conclusions; For total and phase-specific duration, it was found that superior group took shorter time than inferior group. Superior group's Center of Mass was stands for more high value in up-down movement skill than inferior group. However right-left movement scale was less than them. In this reason, superior group was made a straight descent at the same time made a fast front-rear velocity. In the part of up-down movement velocity show that move slowly in the drop-in phase while increased in the bump-up phase. It is show that superior group was less tinny than inferior group include joint angle and knee joint angle. However leaning angle of trunk and the body inclination angle were more high figured than inferior group. Leaning angle of lower limbs also showed high figure at the center mogul. Lastly, In the part of body torsion angle show that superior group was high figure direction of right turn in the drop-in phase while in bump-up phase, made a high figure direction of left turn.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.18 no.3
• /
• pp.59-63
• /
• 1981

With substitution with a delicate turn-tree instead of a long permanent cross-tree that is usally located on the derrick post, it is possible to get a large working range of the slewing angle 240 degree and also to decrease the slewing time of the derrick boom, comparing to the exisiting cargo gear system which has the same capacity of slewing winch.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.1
• /
• pp.33-42
• /
• 2001

In switched reluctance motor(SRM) deives, the turn-on and turn-off angles of each phase switch should be accurately controlled for accuracy and efficiency. The accuracy of the switching angles is mainly dependent upon the resolution of the encoder and the sampling period of the microprocessor, that are used to provide the information of the rotor position and to implement a control algorithm of the SRM, respectively. Thus, the higher the speed of the SRM is increased, the larger the amount of the switching angle deviations are from preset turn-on and turn-off angles. Consequently, the motor can not be driven stably high speed region. There fore, a simples and low cost encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using a simple digital logic circuit is also presented for a wide speed range operation.

• Tribology and Lubricants
• /
• v.31 no.3
• /
• pp.125-140
• /
• 2015

In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.232-232
• /
• 2000

switched reluctance motors and drives are increasingly used in industrial applications due to their robust mechanical structure, low inertia and reduction in the rotor losses. As the motor speed increase turn on angle must be advanced to build up phase current. When C-dump converter is applied to switched reluctance motor, the capacitance of dump C has to have proper value. In this paper advance angle for a switched reluctance motor and capacitance of dump C are investigated. Then proper advance angle and the capacitance of dump-C are propose for the industrial low voltage SR motor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.64-70
• /
• 2018

Rollover is a major concern for vehicles with a higher center of gravity and for improving driving performance. This study investigates a tilting system to prevent rollover, which was successfully implemented for high-speed trains. It may be useful to apply the concept of the tilting system to a large truck such as a trailer. Even a small adjustment in the tilting angle can improve the driving stability during a steep turn. The equation of motion was derived from a dynamic model of the trailer with the tilting system. The balance of the centrifugal force and normal force determines the rollover critical speed for a given radius of the turn and load. To obtain a more conservative criterion, the rollover critical state was defined as the instant when any side wheel loses contact with the road. To actuate the tilting system, the optimal tilting angle must be calculated from the steering angle and the vehicle speed. Using a simplified model of a large truck, the effects of the tilting angle and load on the rollover critical speed were investigated.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1527-1536
• /
• 2014

This paper investigates the optimal values of turn-on and turn-off angles, and ratio of flux linkage at turn-off angle and peak phase current positions of optimal control for accomplishing maximum output power in an 8/6 Switched Reluctance Generator (8/6 SRG). Phase current waveform is analyzed to determine optimal excitation angles (optimal turn-on and turn-off angles) of the SRG for maximum output power which is applied from a nonlinear magnetization curve in terms of control variables (dc bus voltage, shaft speed, and excitation angles). The optimal excitation angles in single pulse mode of operation are proposed via the analytical model. Simulated and experimental results have verified the accuracy of the analytical model.