• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.5
• /
• pp.435-442
• /
• 2014

This paper describes an improved design model that can be used to configure a non-contact pneumatic device to turn a large sheet at the in-line system. For rotational moving in the conveyor system, the conventional method is to turn the system itself. The improved non-contact pick-up system mainly uses 8 pairs of L-shaped latches and 12 swirl type heads. It is positioned above the upward air flow table. This system performs the non-contact gripping and side-edge contact support in the vertical and rotational directions to hold the self-weight of a large flat sheet. A non-contact air head can exert a sufficient gripping ability at 4N lower than the standard working pressure. The side latches support 60% of the lifting force required. Through structural and flow analysis, the working conditions were simultaneously considered in accordance with the deflection and flatness of the glass.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.8 no.2
• /
• pp.1193-1199
• /
• 1966

More stable and higher yields in rice paddy depend mainly upon an adequately balanced supply of water for higher yield. Rice paddy is supplied naturally by rainfall but inevitably requires artificial supplenental irrigation for higher yields. Even though it may be true that the water requirement of rice plants is generally higher than those of other crops, the submerged condition is not necessarily required for rice. The moisture requirements of rice vary according to its growing stages and it is possible to increse the irrigation efficiency by means of lessening the loss due to percolation and evapolation in the field. This experiment was conducted on the effect of the various amount of water supply and different irrigation periods for yield and yield components, and was carried out to find out the most suitable irrigation method and to increase the irrigation efficiency for higher yields in rice paddy. Randomized block design with 3 replications was employed where the 3 levels of the amount of irrigation water; (120% moisture contents), unirrigated (90~100%) and more un irrigated candition (80~90% moisture content), and levels of the various irrigation periods; usual, initial, intermediate and final periods, being treated. The results obtained in this experiment are as follows: 1. As for the physical and chemical and soil properfies, and other characteristics, there are no differences among the treatments enough to be effective for the growth of rice plants. 2. Culm length was measured after harvest as shown in table 2. 3. Difference of the amount of irrigation water did not change the culm length and ear length, however it also indicated more apparent increase in final treatment plots thatn that of usual. 3. No difference in the number of ears and number of ears pers per hill was founded treatments both in the difference of water supply and in the various irrigation periods. 4. There is no difference in the maturing rate and 1000 grains weight. 5. The number of panicles and grains and more increased in 80~100% moisture contents soil than those of 120%. and it shows in un irrigated plots, more irrigated plots and control plots in turn. Other wise according to the period\ulcorner of irrigation the trend is appeared in turn initial, usual, final and intermediate treatments.6. Yield as shown in table 7. 8 was more increased in unirrigated plots(90~IOO% moisture content) than the control plots (120% moisture content) by up to 8.2% and also 3. 2% in more unirrigated plots than that of control by periods is shown: usual plots final, initial, inter mediate treatment plots in turn. 7. The above resutts lead to the conclusion that no remarkable, differences in yields and soil properties are made by the unirrigation. However, it is apparent that this treatment has .some advantages in the points that one could spare the amount of water supply for irrigation with more increase in yield. In addition, a higher temperature and a brisk oxygen supply would be possible throug h this treatments. Accordingly, these treatment would be a more reasonable and economical cultivation method of rice for the better harvest.

• Journal of Korean Society of Transportation
• /
• v.7 no.1
• /
• pp.35-42
• /
• 1989

The multinomial logit model has been applied for various choice problems. Among others, the joint destination mode choice, the mode choice and the route choice are the three major modeling topics for korean transportation planners. This paper examines with real world data (the Olympic road and its competing two major arterials) the usefulness of a Logit route choice model. Quites surpisingly, it is found that the multinomial route choice behavioral model calibrated for this study based on (0,1) individula data base can not provide a good estimate for O-D trips less than 6㎞. 400data points and 3case studies might not be sufficient for a sound conclusion. It is, however, believed from a series of similar studies conducted by the authors that the route choice behavior is more sensitive (more demand elastic with respect to travel time changes) than the mode choice and the shorter trip, the more sensitive. The travel time parameters for destination choice models are usually smalle than the travel time parameters for mode choice models and these parameters (for mode choice models) turn our smaller than the travel time parameters for route choice models from this study. Table 2 in this paper shows parameter changes for three different markets and Table 3 shows the modeling errors when the estimated individual probabilities are aggregated into a route level.

• Korean Journal of Applied Biomechanics
• /
• v.24 no.4
• /
• pp.317-327
• /
• 2014

As a single subject study, it was purposed to investigate kinematic differences between Yang Hak Seon vault (i.e., handspring forward and salto forward straight with triple twist, Yang-1 vault hereafter) and Tsukahara $1260^{\circ}$ twist with salto forward straight (Yang-2 vault hereafter) in gymnastics. Yang Hak-Seon (23 years, 160 cm, and 52 kg) voluntarily participated in this study. Motion capture system, consisting of fourteen cameras, were used to measure Yang-2 vault with the sampling rate of 200 Hz. Twenty six reflective markers were placed on major anatomical points of 15 body segments. Successful two trials of Yang-2 vault were collected and analyzed for the comparison. Compared Yang-1 results were based on the previous study of Park and Song (2012). Results indicated superior linear kinematics of Yang-1 vault to those of Yang-2 vault before the touchdown of vault table. However, Yang-2 vault revealed superior angular kinematics to Yang 1 vault showing more trunk twist angle (a triple and a half twist) and its faster angular velocity during the airborne. The Yang 2 vault could has advantage of increasing angular motion than Yang 1 vault as a result of a half turn off the springboard onto the vault table and a sequential touchdown of the hands.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.862-874
• /
• 1989

A phase evil method and spectrum analysis were instrument error which is originated from measurement system and the form error of standard specimens. An instrument with a rotating table supported by an air bearing is calibrated using standard specimens. The phase of standard specimens was measured 12 times on the rotating table with rotating 30 in turn and its measurement magnification was set by 100000 times. As a result of data analysis of all the observations, read out at each of 144 orientations(per 2.5) from recorded datafiles, the error of the performance of the instrument and those of the standard specimens are evaluated and a systematic deviation of the instrument is determined. In the particular instrument used in the present experiment, the deviation of the instrument is determined with the accuracy of 15nm and those of standard specimens with the accuracy of 23, 13 n, respectively. The reproducibility of the instrument is investigated, too. If the instrument is calibrated by using the above standard specimens, then the accuracy of the measurement of roundness error can be improved to about 15nm.

• Journal of Science of Art and Design
• /
• v.2
• /
• pp.239-293
• /
• 2000

The paper aims to study how to describe the rigorous position on which semantic elements are laid, within the visual space. This purpose is, first of all, for the construction of visual syntactical semantics of the visual space. For this aim, the preliminary research begins with some definitions on : 1) visual space, visual design, visual syntactical semantic meaning, 2) position, sequence of position, 2-dim. sequence of position, and 3) 2-dim. numerical series of position, harmonious dynamic values. Here, The main issue is to define the position in general. To solve this problem, the researcher surveyed the positions on which the sets of pixemes are set up. The results are as follows ; 1. As far as the positions in visual space are concerned, they are the possible locations permitted in the visual patches. They are not the factual but the possible positions. 2.The position value that the sequential point has is not arithmetical but harmonious-dynamic, for it is not permitted for its own sake, but for the person, that is to say, for the viewer's visual perception. 3. The harmonious-dynamic value of positional sequence can be composed of the 2-dimensional successive numerical series which is, in turn, composed of the primordial 3 values x0, $\mu0$, y0. Here, the $\mu0$ is the harmonious mean value of x0 and y0. The x0 and y0 are, therefore, of the mutual dynamic relationship. 4. From this, the 2-dim general $\Delta-TABLE$ of the numerical series of position in visual design could be acquired through development of the primordial 3 values into the $X_i,\;Y_i$, orbit values.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.8
• /
• pp.67-75
• /
• 2010

In this study, a series of 1 g shaking table tests were carried out for a single pile in soft clay with various input acceleration amplitudes and frequencies. Based on the results, dynamic p-y curves were drawn and, in turn, the dynamic p-y backbone curve was formed by connecting the peak points, corresponding to the maximum soil resistance, of the dynamic p-y curves. In order to represent the p-y backbone curve numerically, Matlock's p-y formulations for clay was used to find the initial stiffness ($k_{ini}$) and the ultimate capacity ($p_u$) of the clay, both of which are required to formulate the p-y backbone curve as a hyperbolic function. The suggested p-y backbone curve was verified through comparisons with currently available p-y curves as well as other researchers' centrifuge test results and numerical analysis results.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.138-142
• /
• 2010

The thrust axis alignment of the launch vehicle is very important because of the misalignment causes the unstable attitude control and results in mission failure. Generally, optical methods such as digital theodolite and laser tracker and mechanical method such as turn table method are used to align thrust axis to vehicle axis. This article deals with the simple method of thrust axis alignment of Kick Motor.

• Journal of Korea Multimedia Society
• /
• v.18 no.10
• /
• pp.1180-1188
• /
• 2015

In this paper, a parallel cell contour line extraction algorithm using CUDA, which has no inner contour lines, is proposed. The contour of a cell is very important in a cell image analysis. It could be obtained by a conventional serial contour tracing algorithm or parallel morphology operation. However, the cell image has various damages in acquisition or dyeing process. They could be turn into several inner contours, which make a cell image analysis difficult. The proposed algorithm introduces a min-max coordinates table into each CUDA thread block, and removes the inner contour in parallel. It is 4.1 to 7.6 times faster than a conventional serial contour tracing algorithm.

• Journal of the Korean Home Economics Association
• /
• v.33 no.4
• /
• pp.189-198
• /
• 1995

This study discusses the traditional main life culture of Korea and the relations with the traditional manners of Korean culture. According to studies of literature and an analysis, it shows the traditional courtesy can be linked to the housing structure of the Cho-sun dynasty which can be termed as a representation of traditional Korean society. Housing culture of Cho-sun dynasty led to a most characteristic living culture. To be specific sit-down culture use norms, hierarchy and fittings can be sited. The sit-down culture in turn led to the main courtesies of greeting, table manners, etiquette for entrance and exit, the carefulness shown to elders, the self-restraint of speech and action and the manners between men and women, But in today's world there are realistic difficulties that make the application of these norms in everyday life difficult. But at the same time we must realize that there are traditional norms which overcome time and which affect today's norms.