• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.571-572
• /
• 2006

Tungsten CMP needs interconnect of semiconductor device ULSI chip and metal plug formation, CMP technology is essential indispensable method for local planarization. This Slurry development also for tungsten CMP is important, slurry of metal wiring material that is used present is depending real condition abroad. It is target that this research makes slurry of efficiency that overmatch slurry that is such than existing because focus and use colloidal silica by abrasive particle to internal production technology development. Compared selectivity of slurry that is developed with competitor slurry using 8" tungsten wafer and 8" oxide wafer in this experiment. And removal rate measures about density change of $H_2O_2$ and Fe particle. Also, corrosion potential and current density measure about Fe ion and Fe particle. As a result, selectivity find 83:1, and expressed similar removal rate and corrosion potential and current density value comparing with competitor slurry.

• 한국전기전자재료학회논문지
• /
• 제17권2호
• /
• pp.156-161
• /
• 2004

We investigated the effects of oxidizer additive on the performance of Cu-CMP process using commonly used tungsten slurry. In order to compare the removal rate and non-uniformity as a function of oxidizer contents, we used alumina-based tungsten slurry and copper blanket wafers deposited by DC sputtering method. According to the CMP removal rates and particle size distribution, and the microstructures of surface layer by SEM image as a function or oxidizer contents were greatly influenced by the slurry chemical composition of oxidizers. The difference in removal rate and roughness of copper surface are believed to cause by modification in the mechanical behavior of $Al_2$O$_3$abrasive particles in CMP slurry.

• Transactions on Electrical and Electronic Materials
• /
• 제7권4호
• /
• pp.163-166
• /
• 2006

The dishing and the erosion were evaluated on the tungsten CMP process with conventional and new developed slurry. The tungsten thin film was polished by orbital polishing equipment. Commercial pattern wafer was used for the evaluation. Both slurries were pre tested on the oxide region on the wafer surface and the removal rate was not different very much. At the pattern density examination, the erosion performance was increased at all processing condition due to the reduction of thickness loss in new slurry. However, the dishing thickness was not remarkably changed at high pattern density despite of the improvement at low pattern density. At the large pad area, the reduction of dishing thickness was clearly found at new tungsten slurry.

• 한국초전도ㆍ저온공학회논문지
• /
• 제22권2호
• /
• pp.17-20
• /
• 2020

Comprehensive utilization of tungsten tailings resources not only solves environmental problems but also creates huge economic benefits. The high content of iron impurity in tungsten tailings will have adverse effect on the downstream comprehensive utilization, whether flotation or pickling. In this paper, the Superconducting High Gradient Magnetic Separation(S-HGMS) is used to remove of Fe impurities from tungsten tailings. The optimal experimental parameters are as follows: background magnetic induction intensity is 3.0T, slurry flow velocity is 500ml/min. The Fe removal rate of Fe was 68.8% and the recovery rate was 59.53%.

• 한국전기전자재료학회논문지
• /
• 제18권9호
• /
• pp.787-792
• /
• 2005

Chemical mechanical polishing(CMP) has become the process of choice for modem semiconductor devices to achieve both local and global planarization. CMP is a complex process which depends on numerous variables such as macro, micro and nano-geometry of pad, relative velocity between pad and wafer stiffness and dampening characteristics of pad, slurry, pH, chemical components of slurry, abrasive concentration, abrasive size, abrasive shape, etc. Especially, an oxidizer of chemical components is very important remove a target material in metal CMP process. This paper introduces the effect of oxidizer such as $H_2O_2,\;Fe(NO_3)_3\;and\;KIO_3$ in slurry for tungsten which is used in via or/and plug. Finally the duplex reacting mechanism of $oxidizer(H_2O_2)$ through adding the $catalyst(Fe(NO_3)_3)$ could acquire the sufficient removal rate in tungsten CMP.

• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.568-574
• /
• 2000

We have been optimized tungsten(W) plug CMP(chemical mechanical polishing) characteristics using two different kinds of component of slurry and two different kinds of pad which have different hardness. The comparison of oxide film roughness on around W plug after polishing has been carried out. And W plug recess for consumable sets and dishing effect at dense area according to the rate of over-polishing has been investigated. Also the analysis of residue on surface after cleaning have been performed. As a experimental result we have concluded that the consumable set of slurry A and hard pad was good for W plug CMP process. After decreasing the rate of chemical reaction of silica slurry and adding two step buffering we could reduce the expanding of W plug void however we are still recognizing to need a more development for those kinds of CMP consumables.

• 분석과학
• /
• 제19권5호
• /
• pp.394-399
• /
• 2006

본 연구에서는 반도체 웨이퍼 연마 공정에 사용한 산화제와 첨가제의 연마 속도에 미치는 영향과 전기 화학적 특성에 대해 조사하였다. 산화제로는 과산화수소, 질산화 철과 요오드산 칼륨을 사용하였으며, 이들은 연마액의 pH와 종류에 따라 텅스텐 막질에서 상이한 산화반응을 나타내었다. 이러한 차이점은 연마성능에 영향을 끼치며, 과산화수소는 식각반응이 질산화 철과 요오드산 칼륨에서는 부동태 반응이 우세하였다. 그리고 염기성 화합물인 TMAH와 KOH를 연마액에 첨가하였을 때 텅스텐에 대한 전위 에너지 변화 증가 및 연마 제거속도 증가를 확인할 수 있었으며, 제타 전위 값의 절대 값 증가를 통해 분산성 향상에도 도움이 되는 것을 알 수 있었다. 마지막으로 음이온 계면 활성제중 평균 분자량이 25만인 폴리아크릴산을 100 ppm 첨가시 연마 입자의 뭉침 현상이 줄어들면서 분산성 향상에 효과적인 것을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제18권4호
• /
• pp.303-308
• /
• 2005

In this paper, the effects of oxidants on tungsten chemical mechanical polishing (CMP) process were investigated using three different oxidizers such as Fe(NO₃)₃, KIO₃ and H₂O₂. Moreover, the interaction between the tungsten film and the oxidizer was discussed by potentiodynamic polarization measurement with three different oxidizers, in order to compare the effects of W-CMP and electrochemical characteristics on the tungsten film as a function of oxidizer. As an experimental result, the tungsten removal rate reached a maximum at 5 wt％ Fe(NO₃)₃concentration, and when 5 wt％ H₂O₂was added in the slurry, the removal rate of W increased. Also, the microstructures of surface layer by atomic force microscopy(AFM) image were greatly influenced by the slurry chemical composition of oxidizers. It was shown that the surface roughness and removal rate of the polished surface were improved in Fe(NO₃)₃than KIO₃. The electrochemical results indicate that the corrosion current density of the 5 wt％ H₂O₂ and 5 wt％ H₂O/sub 2+/＋ 5 wt％ Fe(NO₃)₃was higher than the other oxidizers. Therefore, we conclude that the W-CMP characteristics are strongly dependent on the kinds of oxidizers and the amounts of oxidizer additive.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.366-367
• /
• 2006

In general, HF chemistry lifts off the particles during scrubbing after polishing and effectively removes particles. It is sometimes impossible to apply HF chemistry on W plug due to the degradation of electrical characteristics of a device. In this paper, a post W CMP cleaning process is proposed to remove residue particles without applying HF chemistry. After W CMP, recessed plugs are created, therefore they easily trap slurry particles during CMP process. These particles in recessed plug are not easy to remove by brush scrubbing when $NH_4OH$ chemistry is used for the cleaning because the brush surface can not reach the recessed area of plugs. Buffing with oxide slurry was followed by W CMP due to its high selectivity to W. The buffing polishes only oxide slightly which creates higher plug profiles than surrounding oxide. Higher profiles make the brush contact much more effectively and result in a similar particle removal efficiency even in $NH_4OH$ cleaning to that in HF brush scrubbing.

• 한국정밀공학회지
• /
• 제21권7호
• /
• pp.22-29
• /
• 2004

As a result of high integration of semiconductor device, the global planarization of multi-layer structures is necessary. So the chemical mechanical polishing(CMP) is widely applied to manufacturing the dielectric layer and metal line in the semiconductor device. CMP process is under influence of polisher, pad, slurry, and process itself, etc. In comparison with the general CMP which uses the slurry including abrasives, fixed abrasive pad takes advantage of planarity, resulting from decreasing pattern selectivity and defects such as dishing & erosion due to the reduction of abrasive concentration especially. This paper introduces the manufacturing technique of fixed abrasive pad using hydrophilic polymers with swelling characteristic in water and explains the self-conditioning phenomenon. And the tungsten CMP using fixed abrasive pad achieved the good conclusion in terms of the removal rate, non-uniformity, surface roughness, material selectivity, micro-scratch free contemporary with the pad life-time.