• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.120-123
• /
• 1993

This paper describes the deposition and characteristics of electrochromic tungsten oxide thin films for electrochromic smart windows. Tungsten Oxide thin films(WO$_3$) are deposited by thermal evaporation techniques. By varying deposition parameters, WO$_3$ thin films exhibit different optical properties. The electrochromic devices are consist of ITO glass/ WO$_3$ thin films/ LiClO$_4$-propylene carbonate electrolyte/ counter electrode. The electrochromic properties of tungsten oxide thin films with different deposition condition ale investigated.

• 한국재료학회지
• /
• 제23권12호
• /
• pp.680-686
• /
• 2013

Tungsten oxide films were prepared by an electrochemical deposition method for use as the anode in rechargeable lithium batteries. Continuous potentiostatic deposition of the film led to numerous cracks of the deposits while pulsed deposition significantly suppressed crack generation and film delamination. In particular, a crack-free dense tungsten oxide film with a thickness of ca. 210 nm was successfully created by pulsed deposition. The thickness of tungsten oxide was linearly proportional to deposition time. Compositional and structural analyses revealed that the as-prepared deposit was amorphous tungsten oxide and the heat treatment transformed it into crystalline triclinic tungsten oxide. Both the as-prepared and heat-treated samples reacted reversibly with lithium as the anode for rechargeable lithium batteries. Typical peaks for the conversion processes of tungsten oxides were observed in cyclic voltammograms, and the reversibility of the heat-treated sample exceeded that of the as-prepared one. Consistently, the cycling stability of the heat-treated sample proved to be much better than that of the as-prepared one in a galvanostatic charge/discharge experiment. These results demonstrate the feasibility of using electrolytic tungsten oxide films as the anode in rechargeable lithium batteries. However, further works are still needed to make a dense film with higher thickness and improved cycling stability for its practical use.

• 한국표면공학회지
• /
• 제26권1호
• /
• pp.3-9
• /
• 1993

Chemical vapor deposited tungsten films were formed in a cold wall reactor at pressures higher (10~120torr) than those conventionally employed (<1torr). SiH4, in addition to H2, was used as the reduction gas. The effects of pressure and reaction temperature on the deposition rate and morphology of the films were ex-amined under the above conditions. No encroachment or silicon consumption was observed in the tungsten de-posited specimens. A high deposition rate of tungsten and a good step coverage of the deposited films were ob-tained at 40~80 torr and at a temperature range of $360~380^{\circ}C$. The surface roughness and the resistivity of the deposited film increased with pressure. The deposition rate of tungsten increased with the total pressure in the reaction chamber when the pressure was below 40 torr, whereas it decreased when the total pressure ex-ceedeed 40 torr. The deposition rate also showed a maximum value at $360^{\circ}C$ regardless of the gas pressure in the chamber. The results suggest that the deposition mechanism varies with pressure and temperature, the surface reac-tion determines the overall reaction rate and (2) at higher pressures(>40 torr) or temperatures(>36$0^{\circ}C$), the rate is controlled by the dtransportation rate of reactive gas molecules. It was shown from XRD analysis that WSi2 and metastable $\beta$-W were also formed in addition to W by reactions between WF6 and SiH4.

• 전자공학회논문지A
• /
• 제29A권4호
• /
• pp.49-57
• /
• 1992

Tungsten film was deposited on the TiN surface in a low pressure chemical vapor deposition reactor and chemical reaction mechanism between TiN surface and ($WF_{6}\;and\;SiH_{4}$ was studied. Interaction of ($WF_{6}\;or\;SiH_{4}$ with TiN surface and tungsten was deposited more easily. $WF_6$ reacted with TiN activated the TiN surface to form volatile TiF_4$ and tungsten nuclei were formed. ($SiH_{4}$ was dissociated on the TiN surface to form silicon nuclei. From RBS and AES analysis, we could not detect the impurities(such as Si or TiF$_x$)at the interface between tungsten and TiN. The adhesion at the W/TiN interface became poor when the deposition temperature was below 275$^{\circ}C$.

• 한국정밀공학회지
• /
• 제22권8호
• /
• pp.165-173
• /
• 2005

This paper presents the results for deposition of micrometer-scale metal lines on glass for the development of TFT-LCD circuit repair-system. Although there had been a few studies in the late 1980's for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and W(CO)s was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 m depending on laser power and scan speed while the width was controlled between 50um using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below $1{\Omega}{\cdotu}um$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.

• 한국표면공학회지
• /
• 제23권1호
• /
• pp.27-33
• /
• 1990

Thermodynamic analysis on silicon consumpton during the chemical vapor deposition of tungten was carried out by calculation equilibrium concerations of all possible product species utilizing a computer progrom according to VCS.(Villars-Cruise-Smith) algorithm. The calculation could show various reaction paths which dominate the tungsten deposition under different process conditions. According to the calculation, the consumption of silicon can also be reduced at a lower total pressure SiH4 without H2 as the reacting gas is most effective for suppression of the excessive consumption of silicon during the deposition process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.657-662
• /
• 2005

In this study, the deposition of micrometer-scale metallic interconnects on LCD glass for the repair of open-circuit type defects is investigated. Although there had been a few studies Since 1980 s for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and $W(CO)_6$ was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 nm depending on laser power and scan speed while the width was controlled between $3\~50{\mu}$ using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below 1 $O\cdot{\mu}m$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.

• 대한전자공학회논문지
• /
• 제27권10호
• /
• pp.113-123
• /
• 1990

저압화학증착 반응기에서 $WF_{6}$와 $SiH_{4}$를 사용해 단결정 실리콘 웨이퍼에 텅스텐 박막을 증착시키는 실험을 $250-400^{\circ}C$에서 하였다. 텅스텐 박막이 증착되는 속도는 기상에서 기판표면으로 반응기체가 이동하는 과정에 의해 결정되는 것으로 나타났으며 생성된 박막에서는 약 $3{\%}$ 정도의 실리콘이 함유되어 있는 것으로 나타났다. 증착온도가 높아질수록 박막의 결정성이 뚜렷해지고 grain의 크기도 커지는 것으로 나타났다. 증착된 박막의 비저항은 $7~25{\mu}{\Omega}-cm$ 정도이며 증착온도가 높아질수록 작아지는 것으로 나타났다. 테이프 테스트에 의해 접합도를 측정한 결과 증착온도가 높을수록 접합도가 좋아지는 것으로 나타났다. 반응생성물을 분석한 결과 HF가 생성되는 반응보다는 $SiF_{4}$와 수소가 발생하는 반응이 일어나는 것으로 관측되었다.

• 한국표면공학회지
• /
• 제15권3호
• /
• pp.138-145
• /
• 1982

The effects of the simultaneous variations of the ratio of feed gases(H2/N2 Flow ratio), feed gas flow rate (H2/N2, total-flow rate) and partial pressures of TiCl4 (PTiCl41) as well as deposition time and cobalt content of the substrate on the deposition rate of the TiN Coated Cemented Tungsten Carbide Tools were investigated. Deposition was carried out in the temperature range of 930$^{\circ}C$-1080$^{\circ}C$ and an activation energy of 46.5 Kcal/mole can be calculated. Transverse rupture strength was noticeably reduced by the TiN coating on the virgin surfa-ce of Cemented Tungsten Carbide, the extent of which was decreased according to the coa-ting thickness. Microhardness value observed on the work was in the range of 1700∼2000kg/mm, which were in well agreement with the value of bult TiN. The wear resistance of TiN layers was performed by turning test and it was observed that crater and flank resistance remarkably enhanced by TiN coating.

• 한국정보통신학회논문지
• /
• 제6권5호
• /
• pp.689-695
• /
• 2002

막질의 조성은 공정 개발과 고품질 생산 적용을 위한 반도체 소자의 제조에 있어서 풍요한 요소의 하나 이다. 막의 표면과 계면의 조성은 기본적으로 AES측 통하여 알 수 있다. 본 연구에서는 온도, DCS post flow, shower head life time 등과 같은 공정조건으로 LPCVD법을 이용한 tungsten suicide 박막을 증착하고 이들의 구조적, 전기적 특성과 조성비를 측정하며 WSix박막을 해석하였고 이로부터 Si/W의 조성비를 비교하였다. Si와 W의 조성비는 DCS post flow에 의하여 WSix박막의 표면에서 증가하였으며, 폴리실리콘과 tungsten silicide 계면에서는 온도의 증가에 따라 조성비가 증가함을 알 수 있었다. 이 결과는 메모리 소자 제조의 WSix 박막 증착의 공정조건 최적화에 적용될 수 있다.