• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.12
• /
• pp.130-138
• /
• 1995

Machined graphite/epoxy surfaces were studied by using SEM (Scanning Electron Microscopy), surface profilometry and its analysis to determine suitable surface describing parameters for machined unidirectional and multidirectional laminate composite. The surface roughness and profile are found to be highly depdndent on the fiber layup direction and the measurement direction. It was possible to machine 90 .deg. and -45 .deg. plies due to the adjacent plies, which were holding those plies. It was found that the microgeometrical variations in terms of roughness parameters $R_{a}$ without $D_{y}$(Maximum Damage Depth) region and $D_{y}$are better descriptors of the machined laminate composite surface than commonly used roughness parameters $R_{a}$and $R_{max}$ The characteristics of surface profiles in laminate composite are well represented in CPD (Cumulative Probability Distribution) plot and PPD (Percentage Probability Density) plot. Edge-trimmed multidirectional laminate surfaces are Gaussian and random for profiles measured along the tool movement direction, they are periodic and non-Gaussian in the direction perpendicular to the tool movement.t.ent.t.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.235-242
• /
• 2014

To investigate pressure distributions on the shaft surface of the air bearing, the commercial CFD software was employed to study three different nozzle geometries to improve the nozzle performance: general drill-shaped, matched cube-shaped and trimmed exit nozzles. Under the influence of stagnation point, the maximum pressure was observed at the center of shaft surface for all cases. Owing to the blocking effect of a fine gap between the shaft surface and the nozzle exit, the drill-shaped nozzle has the rapid local pressure increase near the nozzle exit corner, generating the ring vortex in the radial direction within pressure ratio of 6.92, and its pressure becomes negative in a certain range of downstream. In comparison, the contoured nozzle showed a local pressure increase in the measured range of pressure ratios, but a negative pressure appeared within the pressure ratio of about 10. The trimmed nozzle was seemed to extend the high pressure zone near the stagnation point in the radial direction substantially, and no negative pressure was appeared in the whole range. Based on these observations, it is found that trimming nozzle exit becomes more effective for improving the performance than modifying the nozzle inside contour.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.9
• /
• pp.95-103
• /
• 1998

This paper proposes an image segmentation algorithm based on fusion of range and intensity images. Based on Bayesian theory, a priori knowledge is encoded by the Markov random field (MRF). A maximum a posteriori (MAP) estimator is constructed using the features extracted from range and intensity images. Objects are approximated by local planar surfaces in range images, and the parametric space is constructed with the surface parameters estimated pixelwise. In intensity images the ${\alpha}$-trimmed variance constructs the intensity feature. An image is segmented by optimizing the MAP estimator that is constructed using a likelihood function based on edge information. Computer simulation results shw that the proposed fusion algorithm effectively segments the images independentl of shadow, noise, and light-blurring.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.1 s.173
• /
• pp.173-181
• /
• 2000

Depending upon the method of the surface generation and the quality of the boundary curves provided, the resulting surfaces may have global or local irregularities in many cases. Thus it would be necessary for the designer to evaluate the surface quality and to modify the surface. This capability is very important because the defect of the surface requires the rework of the dies that causes a big loss in cost and delivery time. To simulate the reflection line test in the actual production line, a faster generation algorithm is presented. Among., various surface interrogation methods using reflection lines, Blinn-Newell type of reflection mapping is applied to generate reflection lines on the trimmed NURBS surface. The generation of reflection lines is formulated as a surface-plane intersection problem, and solved by surface-contouring techniques. In addition, a modified reflection map is proposed to eliminate the discontinuity of reflection lines due to the configuration of the reflection map. A fast reflection line algorithm is developed utilizing an efficient traced contouring technique, and proved to be well suited for real-time quality-assessment task.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.160-171
• /
• 2001

Depending upon the method of the surface generation and the quality of the designed boundary curves, the resulting surfaces may have global or local irregularities in many cases. Thus, it would be necessary for the designer to evaluate the surface quality and to modify the surface. This is very important because the defect of the surface causes the rework of the dies, increasing cost and delivery time significantly. To simulate the reflection line test in the actual production line, a faster algorithm for generating reflection lines is presented. In this paper, among various surface interrogation methods using reflection lines, Blinn-Newell type of reflection mapping is applied to generate the reflection lines on the trimmed NURBS surfaces. The derivation of reflection lines is formulated as a surface-plane intersection problem (Jung 1994) and is solved by surface-contouring techniques. Also, for eliminating the discontinuity of reflection lines due to the configuration of reflection map, a modified reflection map is proposed. An efficient traced contouring technique is utilized for the computational efficiency and proves to be well suited for the real-time quality-assessment task.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.8
• /
• pp.2163-2172
• /
• 1997

SSI(Surface/Surface Intersection)is a fundamental geometric operation which is used in solid and geometric modeling to support trimmed surface and Boolean operations. In this paper, we suggest a new algorithm for tracing along the intersection curve of two regular surfaces. Thus, in this paper, we present a simplicity of computing and second degree continunity. Given a point of intersection curve, it is traced to entire curve of a intersection curve as the initial point of its and the initial point of each of a intersection curve is detected to DFS(Depth First Search) method in the Quadtree and is naturally presented a continuous form.

• Restorative Dentistry and Endodontics
• /
• v.37 no.3
• /
• pp.155-159
• /
• 2012

Objectives: To investigate the effect of dentin moisture degree and air-drying time on dentin-bond strength of two different one-step self-etching adhesive systems. Materials and Methods: Twenty-four human third molars were used for microtensile bond strength testing of G-Bond and Clearfil $S^3$ Bond. The dentin surface was either blot-dried or air-dried before applying these adhesive agents. After application of the adhesive agent, three different air drying times were evaluated: 1, 5, and 10 sec. Composite resin was build up to 4 mm thickness and light cured for 40 sec with 2 separate layers. Then the tooth was sectioned and trimmed to measure the microtensile bond strength using a universal testing machine. The measured bond strengths were analyzed with three-way ANOVA and regression analysis was done (p = 0.05). Results: All three factors, materials, dentin wetness and air drying time, showed significant effect on the microtensile bond strength. Clearfil $S^3$ Bond, dry dentin surface and 10 sec air drying time showed higher bond strength. Conclusions: Within the limitation of this experiment, air drying time after the application of the one-step self-etching adhesive agent was the most significant factor affecting the bond strength, followed by the material difference and dentin moisture before applying the adhesive agent.

• Journal of the Optical Society of Korea
• /
• v.20 no.2
• /
• pp.314-320
• /
• 2016

The glass thermal forming process provides a high volume, low cost approach to producing aspherical reflectors for x-ray optics. Thin glass sheets are shaped into mirror segments by replicating the mold shape at high temperature. Heating parameters in the glass thermal slumping process are crucial to improve surface quality of the formed glass. In this research, the heating process of a thermal slumping glass sheet on a concave parabolic mold was simulated with the finite-element method (FEM) to investigate the effects of heating rate and soaking temperature. Based on the optimized heating conditions, glass samples 0.5 mm thick were formed in a furnace with a steel concave parabolic mold. The figure errors of the formed glass were measured and discussed in detail. It was found that the formed glass was not fully slumped at the edges, and should be trimmed to achieve better surface deviation. The root-mean-square (RMS) deviation and peak-valley (PV) deviation between formed glass and mold along the axial direction were 2.3 μm and 4.7 μm respectively.

• Restorative Dentistry and Endodontics
• /
• v.28 no.6
• /
• pp.491-497
• /
• 2003

The purpose of this study was to evaluate the correlation between hybrid layer thickness and bond strength using confocal laser scanning microscope and microtensile bond strength test of two adhesive systems. The dentin surface of human molars. sectioned to remove the enamel from the occlusal surface. Either Scotchbond Multi-Purpose(3M Dental Product, St. Paul, MN, U.S.A) or Clearfil SE Bond (Kuraray, Osaka, Japan) was bonded to the surface. and covered with resin-composite. The resin-bonded teeth were serially sliced perpendicular to the adhesive interface to measure the hybrid layer thickness by confocal laser scanning microscope. The specimen were trimmed to give a bonded cross-sectional surface area of $1\textrm{mm}^2$, then the micro-tensile bone test was performed at a cross head speed of 1.0 mm/min. All fractured surfaces were also observed by stereomicroscope. There was no significant differences in bond strengths the materials(p>0.05). However. the hybrid layers of three-step dentin adhesive system, SM, had significantly thicker than self-etching adhesive system. CS(p<0.05). Pearson's correlation coefficient showed no correlation between hybrid layer thickness and bond strengths(p>0.05). Bond strengths of dentin adhesive systems were not dependent on the thickness of hybrid layer.

• Journal of Korea Foundry Society
• /
• v.25 no.4
• /
• pp.168-172
• /
• 2005

In this study, the effects of chill layers occurred in shot sleeve on the molten metal filling were analyzed through computer simulation and the behavior of chill layers with temperature variation of shot sleeve set from 200 to $280^{\circ}C$ was also investigated. The simulation results showed the chill layers set in the in-gates during the injection process change the main filling direction and cause turbulent flow pattern, resulting in porosities inside the castings. The amount of chill layers with the increasing temperature of shot sleeve was considerably reduced. And particularly, at the setting temperature of $280^{\circ}C$ by heat control unit, the big reduction in chill layers, excellent trimmed surface and the highest densification were achieved, suggesting that as the optimal sleeve condition in diecasting, especially for the highly complex parts like valve body.