• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.33-35
• /
• 2006

We studied the prototypal developments of Plastic Cortex Stimulator (PCS) for stroke patients. The PC sends the stimulation parameters (amplitude, pulse width, cycle, etc.) to the transmitter ZigBee module through serial port. The receiver ZigBee module generates stimulation waveform. The generated output can be controlled by the PC program. Further study can be expanded to portable handset such as PDA using ZigBee. The wireless control of PCS with the handset can help the tele-rehabilitation.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.135-136
• /
• 2007

2.45 GHz RF Transceiver composed RF module and Digital module for USN(Ubiquitous Sensor Network) has been implemented in this paper. The proposed RF system is designed based on IEEE 802.15.4-2006 PHY standard which has a frequency range from $2.4{\sim}2.4835GHz$. In this transmitter chain, the output power is controlled form 0 to 30 dBm. In this receiver chain, less than 20 dB of NF was obtained.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2002.05c
• /
• pp.1-5
• /
• 2002

본 논문에서는 UART(Universal Asynchronous Receiver-Transmitter)를 soft IP(Intellectual Property) 모듈 형태로써 VLSI 설계과정을 통하여 구현하였다. 이 모듈은 현재 각종 통신 디바이스에서 최하 말단에서 직렬 데이터를 시스템으로 받아들이거나 병렬 데이터를 직렬 라인에 실어 보내는 중요한 역할을 담당한다. 본 연구에서 설계한 UART는 간단한 모듈 형태로 제작되어 있어 Verilog-HDL을 사용하여 직렬 송ㆍ수신을 필요로 하는 시스템에 내장되어 사용될 수 있다. 본 논문에서는 설계 순서에 따라 UART를 설계하고 Simulation을 하고 Synopsys Tool을 사용하여 Compile 과 Synthesis 후 Gate Area 와 Belay를 검출해 내었다. 합성결과 0.25$\mu$m 공정의 CMOS Cell Library를 사용하였을 경우 전체 면적은 1,013 gate가 나왔다. 본 논문에서 설계한 UART의 최장경로가 최대 4.12ns로 나타났으며, 최대 동작 클럭 주파수는 200MHz 로써 150Mbps 이상의 전송 속도를 가진다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.139-140
• /
• 2010

This paper presents an indoor prototype for wireless digital signal transmission using Visible Light Communications (VLC) in which high power Light Emitting Diode (LED) is used. Using low cost and off-the-shelf components, the transmitter module is constructed using an AVR Atmega128 microcontroller and commercial white beam LEDs. Modulating the light intensity of the LED enables digital signals to be transmitted across the optical link. The receiver module employs a high speed PIN photodetector for optical signal detection and a recovery circuit for optical-electro signal conversion. By sending digitalized data via VLC technology, many applications can be realized in the areas of consumer advertising, traffic safety information and disaster control.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.342-349
• /
• 2019

We describe and anlayzes the methodology and implementation results of H / W configuration and signal characteristics analysis algorithm for analyzing equipment for analyzing OFDMA physical layer based on 802.16e. Recently, demand for signal analysis of instruments that analyze these signals with the development of digital communication signals is rapidly increasing. Accordingly, it is necessary to develop signal analysis equipment capable of analyzing characteristics of a broadband communication signal using a wideband digital signal processing module. In this paper, we have studied the basic theory of OFDMA in order to devise a device capable of analyzing characterisitcs of broadband communication signals. Second, the structure of OFDMA transmitter/receiver was examined. Third, a wideband digitizer was implemented. we design Wimax signal analysis algorithm based on OFDMA among broadband communication methods and propose Wimax physical layer analysis S/W implementation through I, Q signals. The IF downconverter used the receiver module and the LO generation module of the spectrum analyzer. Quantitative analysis result is obtained through the algorithm of Wimax signal analysis by I, Q data.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.2
• /
• pp.213-219
• /
• 2012

In this paper, we suggested the method of signal integrity for noises and distortion signal generated between high speed information transmission modules by external effects. Suggested method for signal integrity of impedance matching to remove transmission line distortion, We divided the impedance matching between the transmitter and the receiver module with the single line and differential line methods after confirmed the improvement of signal distortions through ADS simulation. the experimental results indicated that it is possible to keep signal integrity without signal distortions by matching the optimal termination impedance which are considering the signal delay of transmission line for using the high-performance modules.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.842-848
• /
• 2011

A fabricated hybrid control board using multi-communication is designed with a low power 8-bit microcontroller, ATxmega128A1. The microcontroller consists of 8 UART (Universal asynchronous receiver/transmitter) ports, 2 kbytes EEPROM, 128 kbytes flash memory, 8 kbytes SRAM. The 8 URAT ports are used for a multi-communication modem, a GPS module, etc. The EEPROM is used for saving a configuration for running programs, and the flash memory of 128 kbytes is used for storing a F/W (Firm Ware), and the 8 kbytes SRAM is used for stack and for storing memory of global variables while running programs. If we use the multi-communication of CDMA, TRS and RF to remotely control Aid to Navigation, it is able to remove the communication shadow area. Even though there is a shadow area for an individual communication method, we can select an optimal communication method. The compatibility of data has been enhanced as using of same data frame per communication device. For the test, 8640 of data have been collected from each buoy during 30 days in every 5 minutes and the receiving rate of the data has shown more than 85 %.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.673-676
• /
• 2008

In wireless communications such as Bluetooth, Baseband should be able to minimize the DC bias of the data which passed the modem interface of either transmitter or receiver for the reliability of the circuit and the integrity of the data. The transmitter scrambles the data to send randomly to the error correction block and the receiver recovers the randomly spread data as they have been. To design the whitening block, it is important to select the prime polynomial for the filtering. In this paper, we designed a optimal whitening block using the prime polynomial $g(D)=D^7+D^4+1$ for hardware and area efficiency. The proposed hardware whitening block was described and verified using Verilog HDL and later to be automatically synthesized. The synthesized whitening block operated at 40Mhz normal clock speed of the target baseband microcontroller.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.1
• /
• pp.13-22
• /
• 2001

This paper presents three dimensional structure of RF packages and the improvement effect of its electrical characteristics when implementing RF transceivers. We divided RF modules into several subunits following each subunit function based on the partitioning algorithm which suggests a method of three dimension stacking interconnection, PAA(pad area array) interconnection and stacking of three dimensional RF package structures. 224MHz ITS(Intelligent Transportation System) RF module subdivided into subunits of functional blocks of a receiver(RX), a transmitter(TX), a phase locked loop(PLL) and power(PWR) unit, simultaneously meeting the requirements of impedance characteristic and system stability. Each sub­functional unit has its own frequency region of 224MHz, 21.4MHz, and 450KHz~DC. The signal gain of receiver and transmitter unit showed 18.9㏈, 23.9㏈. PLL and PWR modules also provided stable phase locking, constant voltages which agree with design specifications and maximize their characteristics. The RF module of three dimension stacking structure showed $48cm^3$, 76.9％ reduction in volume and 4.8cm, 28.4％ in net length, 41.8$^{\circ}C$, 37% in maximum operating temperature, respectively. We have found that three dimensional PAA package structure is able to produce high speed, high density, low power characteristics and to improve its functional characteristics by subdividing RF modules according to the subunit function and the operating frequency, and the features of physical volume, electrical characteristics, and thermal conditions compared to two dimensional RF circuit modules.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.6
• /
• pp.1477-1486
• /
• 2013

In this paper, Implementation of location estimation system using wireless communication technology based on Zigbee. Using wireless communication technology, calculation more accurate location information and service location information to the H/W and S/W has been developed. Receivers, repeaters, smart tag(location device), was developed for implement a location estimation system. The smart tag is built the 120~130KHz, 13~14MHz, 2.0~3.0GHz radio frequency tag. Receiver and repeater is applied to the tag module to recognize the location device's active RFID tags transmit a wireless signal for tag identification. Common Entrance control system in contact with a smart tag, It was implemented to transfer the value of the tag to the access control server over a LAN.