• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.476-480
• /
• 2004

AZO (Al-doped ZnO) thin films were deposited on glass by pulsed magnetron sputtering method, and their structural, electrical and optical properties were investigated. XRD patterns showed that a highly c-axis preferred AZO film was grown in perpendicular to the substrate when pulse frequency of 30 ㎑ was applied to the target. Microstructure of thin films showed that the fibrous grain of tight dome shape was grown. The deposition rate decreased linearly with increase of pulse frequency, and the lowest resistivity was 8.67${\times}$10$\^$-4/ $\Omega$-cm for the film prepared at pulse frequency of 30 ㎑. The optical transmittance spectra of the films showed a very high transmittance of 85∼90%, within visible wavelength region and exhibited the absorption edge of about 350 nm. The characteristics of the low electrical resistivity and high optical transmittance of AXO films suggested a possibility for the application to transparent conducting oxides.

• Korean Journal of Materials Research
• /
• v.15 no.8
• /
• pp.518-520
• /
• 2005

Effects of the $O_2/Ar$ flow ratio in the sputtering process on the crystallinity, surface roughness, carrier concentration, carrier mobility, and optical properties of Al-doped ZnO thin films deposited on sapphire (001) substrates by RF magnetron sputtering were investigated. XRD spectra showed a preferred orientation along the c-axis and a minimum FWHM of the (002) XRD intensity peak for the $O_2/Ar$ flow ratio of 0.5. The (101)peak also appeared and the degree of preferred orientation decreased as the $O_2/Ar$ flow ratio increased from 0.5 to 1.0. AFM analysis results showed that the surface roughness was lowest at the $O_2/Ar$ flow ratio of 0.5 and tended to increase owing to the increase of the grain size as the $O_2/Ar$ flow ratio increased further. According to the Hall measurement results the carrier concentration and carrier mobility of the fan decreased and thus the resistivity increased as the $O_2/Ar$ flow ratio increased. The transmittance of the ZnO:Al film deposited on the glass substrate was characteristic of a standing wave. The transmittance increased as the $O_2/Ar$ flow ratio in-RF magnetron sputtering increased up to 0.5. Considering the effects of the $O_2/Ar$ flow ratio on the surface roughness, electrical resistivity and transmittance properties of the ZnO:Al film the optimum $O_2/Ar$ flow ratio was 0.5 in the RF magnetron sputter deposition of the ZnO:Al film.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.133-140
• /
• 2009

$Ta_{2}O_{5}$ thin films were deposited by RF magnetron sputtering method under various RF power, substrates and oxygen partial pressure. Elliptic constants were measured by using a phase modulated spectroscopic ellipsometer and analyzed with the Tauc-Lorentz dispersion formula and best fit method in the range of 310$\sim$1239 nm. Also, transmittance spectra of the films were measured by UV -Vis spectrophotometer in the range of 300$\sim$1000 nm. From these data, thickness of $Ta_{2}O_{5}$ and surface layer were analyzed and changes of magnitude and shape of dispersion of optical constants according to fabricated conditions were measured. Also, to evaluate thickness and optical constants data analyzed by Tauc-Lorentz dispersion formula, the measured and analyzed transmittance spectra were compared. In result of the comparison, two spectra were in good agreement each other. Accordingly, it indicates that our ellipsometric analysis is valid.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.199-209
• /
• 1994

$PbTiO_3$ thin films were prepared on soda-lime-silica slide glasses, Si-wafer and sapphire substrate by the dip-coating of precursor solution. As starting materials, titanium tetra iso-propoxide and lead acetate trihydrate were used. Then acetylacetone was added to prepare stable sol. The effect of the parameters such as viscosity and composition of sol were investigated. The optical transmittance at visible range, refractive index, IR spectra were measured in varying compositions, thickness and heat treatment temperature. The crystallization of $PbTiO_3$ films were measured by using XRD and SEM. Diffusion of compositions from slide glass to thin film were investigated by using EDX, too. These sols not precipitated for 20 days. Transmittance of $PbTiO_3$ films at visible range were decreased with the increase of thickness and heat treatment temperatures, and were exhibited flat spectra. Pyrochlore type appeared in the films on slide glass and perovskite type appeared in the films on Si-wafer or sapphire at $600^{\circ}C$. Perovskite crystals transformed to $PbTi_3O_7$ phase at $800^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.176-177
• /
• 2013

Surface plasmon polaritons (SPPs) have attracted the attention of scientists and engineers involved in a wide area of research, microscopy, diagnostics and sensing. SPPs are waves that propagate along the surface of a conductor, usually metals. These are essentially light waves that are trapped on the surface because of their interaction with the free electrons of conductor. In this interaction, the free electrons respond collectively by oscillating in resonance with the light wave. The resonant interaction between the surface charge oscillation and the electromagnetic field of the light constitutes the SPPs and gives rise to its unique properties. In this papers, we studied theoretical and experimental extraordinary transmittance (T) and reflectance (R) of 2 dimensional metal hole array (2D-MHA) on GaAs in consideration of the diffraction orders. The 2d-MHAs was fabricated using ultra-violet photolithography, electron-beam evaporation and standard lift-off process with pitches ranging from 1.8 to $3.2{\mu}m$ and diameter of half of pitch, and was deposited 5-nm thick layer of titanium (Ti) as an adhesion layer and 50-nm thick layer of gold (Au) on the semiinsulating GaAs substrate. We employed both the commercial software (CST Microwave Studio: Computer Simulation Technology GmbH, Darmstadt, Germany) based on a finite integration technique (FIT) and a rigorous coupled wave analysis (RCWA) to calculate transmittance and reflectance. The transmittance was measured at a normal incident, and the reflectance was measured at variable incident angle of range between $30^{\circ}{\sim}80^{\circ}$ with a Nicolet Fourier transmission infrared (FTIR) spectrometer with a KBr beam splitter and a MCT detector. For MHAs of pitch (P), the peaks ${\lambda}$ max in the normal incidence transmittance spectra can be indentified approximately from SP dispersion relation, that is frequency-dependent SP wave vector (ksp). Shown in Fig. 1 is the transmission of P=2.2 um sample at normal incidence. We attribute the observation to be a result of FTIR system may be able to collect the transmitted light with higher diffraction order than 0th order. This is confirmed by calculations: for the MHAs, diffraction efficiency in (0, 0) diffracted orders is lower than in the (${\pm}x$, ${\pm}y$) diffracted orders. To further investigate the result, we calculated the angular dependent transmission of P=2.2 um sample (Fig. 2). The incident angle varies from 30o to 70o with a 10o increment. We also found the splitting character on reflectance measurement. The splitting effect is considered a results of SPPs assisted diffraction process by oblique incidence.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1271-1271
• /
• 2001

Water pollutants in drainage mainly consist of organic compounds. Hence, total organic carbon (TOC), chemical oxygen demand (COD), and biochemical oxygen demand (BOD) were generally used as the indices of pollution. However, these values are determined by special analyzer (TOC), titration method (COD), or microbe culture (BOD). Therefore, the development of simple and easy methods for the determination of water pollution is required. The authors reported the evaluation of water pollution by near infrared (NIR) spectroscopy in a model system with food components (Takamura et al. (200) Near Infrared Spectroscopy: Proceedings of 9th International Conference, pp. 503-507). In this study, the relationship between NIR spectra and drainage was investigated in order to develop a method for evaluation of drainage by NIR. Drainage was obtained in Nara Purification Center. The ranges of TOC, COD, and BOD were 0-130, 0-100 and 0-200, respectively. NIR transmittance spectra were recorded on NIR Systems Model 6250 Research Composition Analyzer in the wavelength range of 680-1235 and 1100-2500 nm with a quartz cell (light path: 0.5, 1, 2, 4 and 10mm) at 10-40. Statistical analysis was performed using NSAS program. A partial least squares (PLS) regression analysis was used for calibration. As the result, a good correlation between the raw NIR spectra and OC was obtained in the calibration. The best light path was 10 and 0.5mm in the wavelength range of 680-1235 and 110-2500nm, respectively. In the calibration, correlation coefficients(R) were 096-0.97 in the both range. In the prediction, however, a good correlation (R=0.89-0.96) was obtained only in the range of 6801235 nm, Similar results were obtained in the cases of COD and BOD. These results suggest the possibility that NIR spectroscopy can be used to evaluate drainage.

• Journal of the Korean Chemical Society
• /
• v.42 no.6
• /
• pp.672-678
• /
• 1998

Chitin was extracted from crab shell of Portuns triberculatus and deacethylated to yield chitosan with various molecular weights. The absorption and the fluorescence spectra of Rhodamine 6G(Rh 6G)-sodium dodecyl sulfate(SDS) and Rh 6G-chitosan systems were obtained. From the spectra, we observed that the absorption and the fluorescence intensity of Rh 6G-SDS system decreased when S/D(the concentration of SDS to that of Rh 6G ratio) was below or at 32, while they increased when S/D was above 32. From the suspended solid(SS) removal rate and the transmittance of Rh 6G-SDS-chitosan system, we found that when S/D ratio was 32 its flocculating behaviour was much stronger than Rh 6G-SDS system. As the concentration and the molecular weight of chitosan increased, we also found that S/D range was extended from 32 to 100. With increasing the molecular weight of chitosan, the SS removal rate increased around pH 2~9 but decreased remarkably at pH>12.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.345-346
• /
• 2008

We have studied an emission spectra of top-emssion organic light-emitting diodes(TEOLED) due to a change of cathode and organic layer thickness. Device structure is Al(100nm)/TPD(xnm)/$Alq_3$(ynm)/LiF(0.5nm)/cathode. And two different types of cathode were used; one is LiF(0.5nm)/Al(25nm) and the other is LiF(0.5nm)/Al(2nm)/Ag(30nm). While a thickness of hole-transport layer of TPD was varied from 35 to 65nm, an emissive layer thickness of $Alq_3$ was varied from 50 to 100nm for two devices. A ratio of those two layer was kept to be about 2:3. Al and Al/Ag double layer cathode devices show that the emission spectra were changed from 490nm to 560nm and from 490nm to 560nm, respectively, when the total organic layer increase. Full width at half maximum was changed from 67nm to 49nm and from 90nm to 35nm as the organic layer thickness increases. All devices show that view angle dependent emission spectra show a blue shift. Blue shift is strong when the organic layer thickness is more than 140nm. Devece with Al/Ag double layer cathode is more vivid.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.5
• /
• pp.925-932
• /
• 2001

The influence of ultraviolet(UV)-ray in sun light on human skin has been noted. Textiles can provide protection against harmful UV-radiation. Normally UV-absorbing finishes are used to get better protection. The purpose of this study is to evaluate the UV-cut properties of cotton fabrics treated with UV-absorber. 2,2-dihydroxy-4,4-dimethoxbenzophenone, as UV-absorber was applied to 100% cotton fabric. Reagents added in finishing solution were Triton X-100, polyethylene glycol 400, and $MgCl_2{\cdot}6H_2O$, and C.I. Direct Red 81. Both untreated and treated cotton fabrics were exposed to a xenon arc lamp for 20 and 80 hours. UV absorption spectra of finishing solutions and UV transmission spectra of fabrics were measured by the UV/VIS spectrophotometer. The results of this study can be summarized as follows. The results of this study can be summarized as follows. Absorption and the related transmission spectra were modified in a controlled way with UV-absorber. Absorption effect of UV-absorber was improved by adding Triton X-100, PEG 400, and $MgCl_2{\cdot}6H_2O$ in finishing solution. The UV absorption of finishing solution was in the following order: U/D/T/P/M>D/T/P/M> D/T> D/P, D>U/T/P/M>U/T>T/P/M>T. The UV transmittance of cotton fabrics was remarkably decreased by the application of UV-absorber and additives. The UV-cut properties were most improved by the application of U/D/T/P/M.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.6
• /
• pp.262-266
• /
• 2004

Rutile single crystals were grown by the skull melting method. Ti metal ring was used for initial RF induction heating. The grown crystals were cut into wafer of 5.5 mm diameter and 1mm thickness. The wafers were annealed in air at $1300^{\circ}C$ up to 15 hours and their transmittance spectra $(\lambda= 200~25000 nm)$ were obtained.