• Journal of Drive and Control
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2017

The power train of a concrete truck mixer reducer includes differential planetary gears to get a large reduction ratio for operating the mixer drum in a compact structure. These differential planetary gears are a very important part of the mixer reducer where strength problems are the main concern. Gear bending stress, gear compressive stress and scoring failure are the main concerns. Many failures in differential planetary gears are due to the insufficient gear strength and resonance problems caused by major excitation forces such as gear mating failure in the transmission. In the present study, where the excitation frequencies are the gear tooth passing frequencies of the mating gears, a Campbell diagram is used to calculate differential planetary gear critical speeds. Mode shapes and natural frequencies of the differential planetary gears are calculated by CATIA V5. These are used to predict gear resonance failures by comparing the working speed range with the critical speeds due to the gear transmission errors of the differential planetary gears.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.201-209
• /
• 2000

In this paper, the bit error rate (BER) performance of Multicode DS/CDMA-BPSK communication system is investigated in the presence of multi user interference and Nakagami fading channel environments. The DS/CDMA-BPSK communication system adopts multicode technique to enhance the data transmission rate. Using the calculated BER performance, BER figures of Multicode DS/CDMA-BPSK communication system are shown to discuss the effect of the number of multi user interference, Nakagami fading index, and data transmission rate. From the results, the transmission rate of DS/CDMA-BPSK signal improve by adopting Multicode technique. And we know that the major parameter of BER performance degradation in Multicode DS/CDMA system is the effect of multi user interference than the fading depth.

• ETRI Journal
• /
• v.44 no.4
• /
• pp.543-559
• /
• 2022

To determine a suitable waveform for Internet of Things (IoT) transmission over low-Earth orbit (LEO) satellites, this paper reports the results of a performance comparison between chirp spread spectrum (CSS)-based LoRa and direct sequence spread spectrum (DSSS)-based Ingenu. The performance of both waveforms was measured in terms of the packet error rate, throughput, and packet loss rate, considering the Doppler effect caused by the high speed of LEO satellites and the interference among multiple terminals. Simulation results indicate that the DSSS scheme is more suitable than the CSS scheme for high-traffic IoT services because of its robustness against interference among multiple terminals. However, the CSS scheme is more suitable than the DSSS scheme for high-mobility IoT services because of its robustness against the Doppler effect. We discuss various solutions, such as the preprocessing of Doppler effect and avoidance of packet collision, to enhance the performance of the DSSS and CSS schemes. The simulation results of the proposed solution show that the enhanced DSSS scheme can be a proper waveform in IoT transmission over LEO satellites for both the high-traffic and high-mobility services.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.3
• /
• pp.86-92
• /
• 2000

In this paper, we develop protocol analyzer that can analyze and monitor LAN(Local Area Network)-based TCP/IP protocol using the OOP(object-oriented programming) in Windows98/NT environment. TCP/IP(Transmission Control Protocol/Internet Protocol) protocol analyzer is consist of interface hardware, protocol analysis software and GUI(Graphic User Interface). It is designed for the real-time analysis using the real-time object. In results of Performance test, TCP/IP Protocol analyzer is showed that it can analyze and monitor without frame error in LAN-based. Also, developed protocol analyser operates better than conventional protocol analyzer in performance. It can be used in maintenance fields of communication and network.

• KIPS Transactions on Computer and Communication Systems
• /
• v.10 no.5
• /
• pp.137-144
• /
• 2021

The IETF has recently been standardizing the QUIC protocol for HTTP/3 services. It is noted that HTTP/3 uses QUIC as the underlying protocol, whereas HTTP/1.1 and HTTP/2 are based on TCP. Differently from TCP, the QUIC uses 0-RTT or 1-RTT transmissions to reduce the connection establishment delays of TCP and SCTP. Moreover, to solve the head-of-line blocking problem, QUIC uses the multi-streaming feature. In addition, QUIC provides various features, including the connection migration, and it is available at the Chrome browser. In this paper, we analyze the performance of QUIC for HTTP-based web and streaming services by comparing with the existing TCP and Streaming Control Transmission Protocol (SCTP) in the network environments with different link delays and packet error rates. From the experimental results, we can see that QUIC provides better throughputs than TCP and SCTP, and the gaps of performances get larger, as the link delays and packet error rates increase.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.19-22
• /
• 2005

As the optical communication industry is developed, the demand of optical communication part is increasing. $ZrO_2$ ceramic ferrule is very important part which can determines the transmission efficiency and information quality to connect the optical fibers. In general $ZrO_2$ ceramic ferrule is manufactured by grinding process because the demands precision is very high. And the co-axle grinding process of $ZrO_2$ ceramic ferrule is to make its concentricity all of uniform before centerless grinding. When co-axle grinding of ferrule supported by two pin, pin chucking alignment accuracy is very important. This paper deals with the analysis of the chucking alignment experiment with parallel error on the micro feeding equipment. Thus, if possible be finding highly good the chucking alignment of two pin.

• Journal of Positioning, Navigation, and Timing
• /
• v.3 no.4
• /
• pp.163-170
• /
• 2014

A pseudolite is used as a GPS backup system, and is also used for the purpose of indoor navigation and correction information transmission. It is installed on the ground, and transmits signals that are similar to those of a GPS satellite. In addition, in recent years, studies on the improvement of positioning accuracy using the pseudorange measurement of a pseudolite have been performed. As for the effect of the time synchronization error between a pseudolite and a GPS satellite, a time synchronization error of 1 us generally induces a pseudorange error of 300 m; and to achieve meter-level positioning, ns-level time synchronization between a pseudolite and a GPS satellite is required. Therefore, for the operation of a pseudolite, a time synchronization algorithm between a GPS satellite and a pseudolite is essential. In this study, for the time synchronization of a pseudolite, "a pseudolite time synchronization method using the time source of UTC (KRIS)" and "a time synchronization method using a GPS timing receiver" were introduced; and the time synchronization performance depending on the pseudolite time source and reference time source was evaluated by designing a software-based pseudolite time synchronization performance evaluation simulation platform.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.11
• /
• pp.199-205
• /
• 2000

The vibration and noise of gears is due to the vibration exciting force caused by the tooth stiffness which changes periodically as the mesh of teeth proceeds and by the transmission error, that is, the rotation delay between driving gear and driven gear caused by manufacturing error and alignment error in assembly and so on. The purpose of this study is to develop how to calculate simultaneously the optimum amounts of tooth profile modification, end relief and crowning by minimizing the vibration exciting force of helical gears. We estimate the vibration exciting force by the mesh analysis of gears. The constraints of this problem consist of contact ratio and strengths of gear teeth such as tooth fillet stress, surface durability and scoring. ADS(Automated Design Synthesis) is used as an optimization tool. And, since the aspect ratio is an important parameter of tooth modification, we investigate the relation between it and the optimum values of tooth modification. The proposed method can calculate the optimum amount of tooth modification automatically and is to be utilized to resolve the problem of vibration of helical gears.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.7
• /
• pp.3447-3469
• /
• 2019

It is well-known that the cooperative communication and error control technology can improve the network performance, but most existing cooperative MAC protocols have not focused on how to cope with the contention process caused by cooperation and how to reduce the bad influence of channel packet error rate on the system performance. Inspired by this, this paper first modifies and improves the basic rules of the IEEE 802.11 Medium Access Control (MAC) protocol to optimize the contention among the multi-relay in a cooperative ARQ scheme. Secondly, a hybrid ARQ protocol with soft combining is adopted to make full use of the effective information in the error data packet and hence improve the ability of the receiver to decode the data packet correctly. The closed expressions of network performance including throughput and average packet transmission delay in a saturated network are then analyzed and derived by establishing a dedicated two-dimensional Markov model and solving its steady-state distribution. Finally, the performance evaluation and superiority of the proposed protocol are validated in different representative study cases through MATLAB simulations.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.3
• /
• pp.218-227
• /
• 2017

In this paper, an algorithm to calculate both bearing and distance error for target detection and localization is proposed using the Cramer Rao lower bound to estimate the minium variance of their error in DOA (Direction Of Arrival) estimation. The performance of arrays in detection and localization depends on the accuracy of DOA, which is affected by a variation of SNR (Signal to Noise Ratio). The SNR is determined by sonar parameters such as a SL (Source Level), TL (Transmission Loss), NL (Noise Level), array shape and beam steering angle. For verification of the suggested method, a Monte Carlo simulation was performed to probabilistically calculate the bearing and distance error according to the SNR which varies with the relative position of the target in space and noise level.