• 항공우주시스템공학회지
• /
• 제1권2호
• /
• pp.6-12
• /
• 2007

Flight modes of automatic flight control system for light general aviation flight deck. Garmin G1000, were realized using Stateflow. In developing aircraft, it is difficult to verify the operational flight program in particular branch statement because developer can not see any visual logical steam. So, Stateflow has been used to visualize logical stream, transition from one flight mode to another flight mode. The performance was approved by applying flight mode transition conditions of G1000 to proposed transition system that is composed of states, switches, events, data and transition conditions. DURMI-II was used as 6-DOF simulation model.

• International Journal of Aeronautical and Space Sciences
• /
• 제6권2호
• /
• pp.84-96
• /
• 2005

Helical tip vortex is known as stable vortex structure, however the specific frequency component of far wake perturbation induces the vortex pairing in hover and axial flight. It is expected that the tip vortex pairing phenomena may happen in transition flight and very low advance ratio flight so that inflow may be most nonuniform in the low advance ratio flight. The objectives of this paper are that a tip-vortex instability during the transition from hover into very low advance ratio forward flight is numerically predicted to understand a physics by using a time-marching free-wake method. To achieve the objectives, numerical method is firstly validated in typical axial and forward flights cases. Present scheme with trim routine can predict airloads and inflow distribution of forward flight with good accuracy. Then, the transition flight condition is calculated. The rotor used in this wake calculation is a small-scale AH-1G model. By using a tip-vortex trajectory tracking method, the tip-vortex pairing process are clearly observed in transient flight($\mu$=0.03) and disappears at a slightly higher advance ratio($\mu$=0.05). According to the steady flight simulation at $\mu$=0.03, it is confirmed the tip-vortex pairing process is continued in the rear part of rotor disk and not occurs in the front part. Time averaged inflow in this case is predicted as smooth distribution.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.513-520
• /
• 2004

A steady-state/transient performance simulation model was newly developed for the propulsion system of the CRW (Canard Rotor Wing) type UAV (Unmanned Aerial Vehicle) during flight mode transition. The CRW type UAV has a new concept RPV (Remotely Piloted Vehicle) which can fly at two flight modes such as the take-off/landing and low speed forward flight mode using the rotary wing driven by engine bypass exhaust gas and the high speed forward flight mode using the stopped wing and main engine thrust. The propulsion system of the CRW type UAV consists of the main engine system and the duct system. The flight vehicle may generally select a proper type and specific engine with acceptable thrust level to meet the flight mission in the propulsion system design phase. In this study, a turbojet engine with one spool was selected by decision of the vehicle system designer, and the duct system is composed of main duct, rotor duct, master valve, rotor tip-jet nozzles, and variable area main nozzle. In order to establish the safe flight mode transition region of the propulsion system, steady-state and transient performance simulation should be needed. Using this simulation model, the optimal fuel flow schedules were obtained to keep the proper surge margin and the turbine inlet temperature limitation through steady-state and transient performance estimation. Furthermore, these analysis results will be used to the control optimization of the propulsion system, later. In the transient performance model, ICV (Inter-Component Volume) model was used. The performance analysis using the developed models was performed at various flight conditions and fuel flow schedules, and these results could set the safe flight mode transition region to satisfy the turbine inlet temperature overshoot limitation as well as the compressor surge margin. Because the engine performance simulation results without the duct system were well agreed with the engine manufacturer's data and the analysis results using a commercial program, it was confirmed that the validity of the proposed performance model was verified. However, the propulsion system performance model including the duct system will be compared with experimental measuring data, later.

• 항공우주시스템공학회지
• /
• 제9권1호
• /
• pp.12-18
• /
• 2015

The inter-conversion between different control laws in flight has a lot of risk. The SWM(Switching Mechanism) including logic and stand-by mode is designed to analyze the transient response of aircraft during inter-conversion between different control laws, based on the in-house software for non-real-time and real-time simulation. The SWM applies the fader logic of TFS(Transient Free Switch) to minimize the transient response of an aircraft during the inter-conversion, and applies the reset '0' type of the stand-by mode to prevent surface saturation due to integrator effect in the disengaged flight control law. The transition time is also important to minimize the objectionable transient response in the inter-conversion, as well as the transition control law design. This paper addresses the results of non-real-time simulation for the characteristics of transient response to different transition time to select the adequate transient time, and the real-time pilot evaluation, using SSWM(Software Switching Mechanism) and HSWM(Hardware Switching Mechanism), which is met for Level 1 flying qualities and assures safety of flight.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.389-392
• /
• 2011

본 연구에서는 틸트로터 비행체인 스마트무인기의 비행시험에서 엔진성능 데이터를 추출하고 분석하였다. 비행시험은 프롭로터의 틸트각이 90도에서 0도로 변화하고 다시 0도에서 90도로 변환하는 천이비행 영역에서 이루어졌다. 비행시험으로부터 수집된 엔진성능 데이터로서 엔진 동력과 비연료 소모율은 엔진성능계산프로그램의 예측결과와 잘 일치하였다.

• 제어로봇시스템학회논문지
• /
• 제22권9호
• /
• pp.759-765
• /
• 2016

This paper presents the principle, dynamics modeling and control, hardware implementation, and flight test result of a hybrid-type unmanned aerial vehicle (UAV). The proposed UAV was designed to provide both hovering and fixed-wing type aerodynamic flight modes. The UAV's flight mode transition was achieved through the attitude transformation in pitch axis, which avoids a complex rotor tilt mechanism from a structural and control viewpoint. To achieve this, a different navigation coordinate was introduced that avoids the gimbal lock in pitch singularity point. Attitude and guidance control algorithms were developed for the flight control system. For flight test purposes, a quadrotor attached with a tailless fixed-wing structure was manufactured. An onboard flight control computer was designed to realize the navigation and control algorithms and the UAV's performance was verified through the outdoor flight tests.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.219-224
• /
• 2005

본 연구는 CRW형식 무인항공기 추진시스템의 밸브 작동을 고려한 비행모드에 따른 천이성능특성을 파악하기 위해 SIMULINK를 이용하여 모델링 하였다. 주 엔진시스템의 천이모사에는 ICV 방법이 적용되였다. 그리고 밸브 시스템은 로터리 덕트와 메인 덕트로 빠져나가는 유량을 제어하는 시스템으로서 밸브를 통해 로터리 덕트로 빠져나가는 유량과 메인 덕트를 빠져나가는 유량이 합은 터빈의 출구 유량과 같다는 가정하에 수행 되었으며, 이때 밸브각 변화에 따른 손실, 유량 및 유효 면적 등이 고려되었다. 성능해석은 비행 천이 영역인 고도 1Km 비행 마하수 0.1에서 엔진최대회전수시 회전익 모드에서 고정익 모드로 변환시외 고정익 모드에서 회전익 모드로 변환 경우들이 수행되였다.

• 한국추진공학회지
• /
• 제9권3호
• /
• pp.127-132
• /
• 2005

본 연구는 CRW형식 무인항공기 추진시스템의 밸브 작동을 고려한 비행모드에 따른 천이 성능 특성을 파악하기 위해 SIMULINK를 이용하여 모델링 하였다 그리고 밸브 시스템은 로터리 덕트와 메인덕트로 빠져나가는 유량을 제어하는 시스템으로서 밸브를 통해 로터리 덕트로 빠져나가는 유량과 메인덕트를 빠져나가는 유량의 합은 터빈의 출구 유량과 같다는 가정 하에 수행되었으며, 이때 밸브 각 변화에 따른 손실, 유량 및 유효 면적 등이 고려되었다. 성능 해석은 비행 천이 영역인 고도 1km 비행 마하수 0.1에서 엔진 최대회전수시 회전익 모드에서 고정익 모드로 변환되는 경우와 고정익모드에서 회전익 모드로의 변환되는 경우들이 수행되었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.3-7
• /
• 2007

The characteristics of asymmetric vortex and side force of tangent-ogive-cylinder flight vehicle at high angles of attack have been performed by using upwind Navier-Stokes method with the ${\kappa}-{\omega}$ turbulence model. And Asymmetric transition positions are considered for generation of asymmetric vortex.

• 한국항공우주학회지
• /
• 제44권2호
• /
• pp.116-122
• /
• 2016

터보제트 엔진에서 램제트 엔진으로의 작동 천이를 고려한 TBCC엔진의 성능 특성을 연구하였다. 터보제트 엔진과 램제트 엔진의 성능모델을 제시하고 터보제트와 램제트의 작동 비율을 조절하여 성능 변화가 연속적으로 발생하도록 엔진 작동의 천이 모드를 고려하였다. 이를 통해 다양한 마하수와 고도에서의 완만한 엔진 성능 변화를 나타냈음을 확인하였다. 일정고도(11km)와 가상의 비행 궤적에 대하여 천이 모드를 적용하여 TBCC 엔진의 추력과 비추력의 변화를 분석하였으며, 이를 통해 예상 비행 조건과 엔진의 천이 모드를 고려한 성능 변화와 복합 사이클 엔진 작동 천이 모드의 필요성을 제안하였다.