• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1991년도 특별강연 및 추계학술발표 개요집
• /
• pp.26-28
• /
• 1991

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.69-71
• /
• 2003

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.74-76
• /
• 2003

• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.96-103
• /
• 2000

This study investigated the effects of bonding temperature and bonding atmosphere on high temperature mechanical properties of transient liquid phase(TLP) bonded joints of heat resistant alloy using MBF-50 insert metal. Specimens were bonded at 1,423~1,468K for 600s. Microconstituents of {TEX}$Cr_{7}(C,B)_{3}${/TEX}were formed in the bonded region when the bonding temperature was low. The amount of microcostituents in the bonded layer decreased with increasing the bonding temperature, and the microconstituents in the bonded layer disappeared at the bonding temperature above 1,468K. The tensile strength of the joints at elevated temperatures increased with the increase the bonding temperature and was the same level as one of the base metal in the bonding temperature over 1,453K. Microstructure and alloying element distributions of the bonded region bonded in Ar and $N_2$atmosphere were similar to those of the bonded in vacuum. The creep rupture strength and rupture lives of joints were almost identical to those of base metal.

• Journal of Welding and Joining
• /
• 제21권4호
• /
• pp.69-74
• /
• 2003

The mechanical properties of STD11 Joints by using TLP (Transient Liquid Phase Diffusion) bonding method employing MBF-30 and MBF-80 insert metals were investigated with concerning to the microstructural change. TLP bonding of STD 11 was carried out at 1323∼1423K for 0.6ks∼3.6ks in vacuum. The microstructure and the element distribution of the interlayer between tool steels and insert metals showed specific feature with bonding conditions. It was found that the width of the interlayer increased at initial bonding stage. However, the width of interlayer showed nearly constant value during the isothermal solidification. After isothermal solidification was completed, the joint showed homogeneous element distribution and similar microstructure with base metal because of the grain boundary migration to the bonded interlayer. The bonding strength measured by a tensile test has been varied with the bonding conditions. The maximum joint strength, 760MPa, was obtained with the condition of 1423K for 1.2ks using MBF30 insert metal in this experiment.

• 마이크로전자및패키징학회지
• /
• 제26권4호
• /
• pp.7-13
• /
• 2019

Power module is getting attention from electronic industries such as solar cell, battery and electric vehicles. Transient liquid phase (TLP) boding, sintering with Ag and Cu powders and wire bonding are applied to power module packaging. Sintering is a popular process but it has some disadvantages such as high cost, complex procedures and long bonding time. Meanwhile, TLP bonding has lower bonding temperature, cost effectiveness and less porosity. However, it also needs to improve ductility of the intermetallic compounds (IMCs) at the joint. Wire boding is also an important interconnection process between semiconductor chip and metal lead for direct bonded copper (DBC). In this study, TLP bonding using Sn-based solders and wire bonding process for power electronics packaging are described.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.201-203
• /
• 2003

• 마이크로전자및패키징학회지
• /
• 제19권1호
• /
• pp.17-24
• /
• 2012

Recently, flip chip interconnection has been increasingly used in microelectronic assemblies. The common Flip chip interconnection is formed by reflow of the solder bumps. Lead-Tin solders and Tin-based solders are most widely used for the solder bump materials. However, the flip chip interconnection using these solder materials cannot be applied to temperature-sensitive components since solder reflow is performed at relatively high temperature. Therefore the development of low temperature bonding technologies is required in these applications. A few bonding techniques at low temperature of $150^{\circ}C$ or below have been reported. They include the reflow soldering using low melting point solder bumps, the transient liquid phase bonding by inter-diffusion between two solders, and the bonding using low temperature curable adhesive. This paper reviews various low temperature bonding methods.

• 마이크로전자및패키징학회지
• /
• 제30권4호
• /
• pp.61-68
• /
• 2023

무연솔더에 Fe 입자를 첨가하여 Cu₃Sn 금속간화합물 성장을 억제하고 취성파괴를 방지하는 연구는 보고된 바 있으나 이러한 복합솔더를 TLP(transient liquid phase) 본딩에 적용한 경우는 아직 없다. 본 연구에서는 Sn계 무연솔더 내부에 Fe 입자의 함량을 적절히 조절하여 Sn-3.5Ag-15.0Fe 복합솔더를 제작하고 TLP 본딩에 적용하여 접합부 전체를 Sn-Fe 금속간화합물로 변화시킴으로써 고온 솔더로서의 적용 가능성을 탐색하였다. 접합공정 중에 형성되는 FeSn₂ 금속간화합물은 513℃의 고융점을 가지므로 사용 중 온도가 280℃까지 상승하는 전력반도체용 파워모듈에 안정적으로 적용이 가능하다. 칩과 기판에 ENIG(electroless nickel-immersion gold) 표면처리를 적용한 결과 접합부에 Ni₃Sn₄/FeSn₂/Ni₃Sn₄의 다층 금속간화합물 구조를 형성하였으며 전단시험시 파괴경로는 Ni₃Sn₄/FeSn₂ 계면에서 균열이 진전하다가 FeSn₂ 내부로 전파되는 양상을 보였다. TLP 접합공정 2시간 이후에는 30 MPa 이상의 전단강도를 얻었고 특히 200℃ 전단시험에서도 강도 저하가 전혀 없었다. 본 연구결과는 최근 활발히 연구되고 있는 전기자동차용 파워모듈에 적용할 수 있는 소재 및 공정으로 기대할 수 있다.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.452-455
• /
• 2009

A cost-effective route to synthesize $\beta$-SiAlONs from Si mixtures by reaction bonding followed by post-sintering was investigated. Three different z values, 0.45, 0.92 and 1.87, in $Si_{6-z}Al_zO_zN_{8-z}$ without excess liquid phase were selected to elucidate the mechanism of SiAlON formation and densification. For RBSN (reaction-bonded silicon nitride) specimens prior to post-sintering, nitridation rates of more than 90% were achieved by multistep heating to $1400^{\circ}C$ in flowing 5%$H_2$/95%$N_2$; residual Si was not detected by XRD analysis. An increase in density was acquired with increasing z values in post-sintered specimens, and this tendency was explained by the presence of higher amounts of transient liquid phase at larger z values. Measured z values from the synthesized $\beta$-SiAlONs were similar to the values calculated for the starting compositions. Slight deviations in z values between measurements and calculations were rationalized by a reasonable application of the characteristics of the nitriding and post-sintering processes.