• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.4
• /
• pp.567-573
• /
• 2002

In this paper, we propose a new symbol time synchronization scheme suitable for the OFDM system with an interpolator. The proposed scheme performs the following three steps. In the first step, the coarse symbol time synchronization is achieved by continuously measuring the average power of the received envelope signal. Based on this average power, the detection possibility for the symbol time synchronization is determined. It the signal is sufficient for synchronization, we next perform a relatively accurate symbol time synchronization by measuring the correlation between a short training signal and the received envelope signal. Finally, an additional frequency synchronization is performed with a long training signal to correct symbol synchronization errors caused by the phase rotation. From the simulation results, one can see that the proposed synchronization scheme provides a good synchronization performance over frequency selective channels.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2006.11a
• /
• pp.175-177
• /
• 2006

This letter deals with non-pilot-aided symbol timing estimation methods in an orthogonal frequency division multiplexing (OFDM) system. To do this, OFDM system uses a frequency diversity scheme over two consecutive data symbols. Our approach can be viewed as an expansion of Schmidl's and Minn's correlation methods. Using the OFDM signal equipped with frequency diversity, however, symbol timing is accurately estimated without additional training symbol and a second-order diversity gain is achieved.

• Journal of the Institute of Convergence Signal Processing
• /
• v.2 no.4
• /
• pp.71-76
• /
• 2001

In this paper we propose the Digital Automatic Gain Controller for IEEE 802.11a-High-speed Physical Layer in the 5 GHz Band. The input gain it estimated by calculating the energy of the training symbol that it a synchronizing signal. The renewal gain is calculated by comparing the estimated gain with the ideal gain. The renewal gain is converted into the controlled voltage for GCA to reduce or amplify the input signals. We used a piecewise-linear approximation to reduce the hardware size. The gain control is performed seven times to provide more accurate gain control. The proposed automatic gain controller is designed with VHDL and verified by using the Xilinx FPGA.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.290-297
• /
• 2014

The synchronization of OFDM receiver is consisted of symbol timing offset(STO) estimation in time domain and carrier frequency offset(CFO) estimation in frequency domain. This paper proposes new algorithm for correcting the integer CFO after we have done correcting the STO and partial CFO. ICFO must be corrected, since the ICFO lead to degrade bit error rate(BER) of demodulation performance. The PN sequence has information which is subcarrier order since the modified PN sequence, length is same subcarrier, is used in this paper and is modulated each subcarrier by each chip. Thus the receiver track phase of PN sequence after FFTin order to find the subcarrier frequency offset. The proposed algorithm is faster and more simple than convenient methode as measuring carrier energy.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.5C
• /
• pp.527-539
• /
• 2009

In this paper, we propose an asynchonous ICI (Inter-Cell Interference) mitigation techniques for 3GPP LTE MIMO-OFDMA down-link receiver. An increasing in symbol timing misalignments may occur relative to sychronous network as the result of BS (Base Station) timing differences. Such symbol synchronization errors that exceed the guard interval or the cyclic prefix duration may result in MAI (Multiple Access Interference) for other carriers. In particular, at the cell boundary, this MAI becomes a critical factor, leading to degraded channel throughput and severe asynchronous ICI. Hence, many researchers have investigated the interference mitigation method in the presence of asynchronous ICI and it appears that the knowledge of the SCM (Spatial Covariance Matrix) of the asynchronous ICI plus background noise is an important issue. Generally, it is assumed that the SCM estimated by using training symbols. However, it is difficult to measure the interference statistics for a long time and training symbol is also not appropriate for MIMO-OFDMA system such as LTE. Therefore, a noise reduction method is required to improve the estimation accuracy. Although the conventional time-domain low-pass type weighting method can be effective for noise reduction, it causes significant estimation error due to the spectral leakage in practical OFDM system. Therefore, we propose a time-domain sinc type weighing method which can not only reduce the noise effectively minimizing estimation error caused by the spectral leakage but also implement frequency-domain moving average filter easily. By using computer simulation, we show that the proposed method can provide up to 3dB SIR gain compared with the conventional method.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.11a
• /
• pp.310-312
• /
• 2018

In this paper, We stduy addtional consideration and method to treat carrier frquency offset on defined system parameter & requirements in IALA G1139, previous studied consecutively. We studied the method to treat carrier frequency offset by extending length of training symbol and by differential modulation. This study will publish and argue in IALA ENAV22. We will decide a method to treat carrier frequency offset from result of IALA ENAV22.

• Journal of the Korean Society of Safety
• /
• v.25 no.1
• /
• pp.79-86
• /
• 2010

Although nano materials are used a lot in industries, there has not been any standard nano hazard graphic symbol. An experiment was conducted to know the comprehension ratio of newly designed eight nano graphic symbols. To compare the symbols with existing safety graphic symbols, other sixteen symbols were also included. 54 subjects evaluated the difficulties of graphic symbols on seven point Likert scale and answered the meaning for each symbol. The all eight nano safety symbols marked under 30% comprehension ratio. However, one of them didn't show any statistically significant difference with other existing safety symbols as like bio hazard, radiation, and laser. Therefore the nano symbol tested in the best could be adopted as the nano safety graphic symbol if it is sufficiently exposed in training period and used with warning label. The workers in industries using nano materials can be alerted and protect themselves where the sign is attached.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.9
• /
• pp.1-10
• /
• 2000

This paper proposes symbol decoding schemes combined with channel estimation techniques for coded orthogonal frequency division multiplexing (COFDM) systems in fading channels. sThe proposed symbol decoding schemes are consisted of a symbol decoding technique and channel estimation techniques. The symbol decoding based on Viterbi algorithm is achieved by matching the length of branch word from encoder trellis to the codeword length of symbol candidate on decoder trellis. Three combination schemes are described and their error performances are compared. The first scheme is to combine a symbol decoding technique with a training channel estimation technique. The second scheme joins a decision directed channel estimation technique to the first scheme. The time varying channel transfer functions are tracked by the decision directed channel estimation technique and the channel transfer functions used in the symbol decoder are updated every COFDM symbol. Finally, In order to reduce the effect of additive white Gaussian noise (AWGN) between adjacent subchannels, deinterleaved average channel estimation technique is combined. The error performances of the three schemes are significantly improved being compared with that of zero forcing equalizing schemes.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.899-902
• /
• 1999

In this paper, we designed a equalizer that moved the multipath of channel in 8-VSB transmission receiver. After doing the initial equalization with "LMS(Least Mean Square)"aigorithm. this equalizer used "Stop-and-Go" algorithm. Because of estimating SER(Symbol to Error Ratio) every a training sequence, this can positively cope with transformation of channel and because of using fast clock than symbol-clock(10.76 MHz), we are able to reduce a multiplier.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.3
• /
• pp.9-18
• /
• 2001

In this paper, we present the joint symbol detection and channel estimation for an orthogonal frequency division multiplexing (OFDM) system in fading channels. The proposed methods are based on decision-directed channel estimation (DDCE) method and their symbol detection is achieved by using Viterbi algorithm. This Viterbi decision-directed channel estimation (VDDCE) method tracks time-varying channels and detects a maximum likelihood symbol sequence. Recursive Viterbi decision-directed channel estimation (RVDDCE) method based on VDDCE method is proposed to shorten the detecting depth. In this method, channel estimate and Viterbi processing are recursively performed every interval of training symbol. Also, average chann'el estimation (ACE) technique to reduce the effect of additive white Gaussian noise (AWGN) is applied VDDCE method and RVDDCE method. These proposed methods arc demonstrated by computer simulation.