• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.2
• /
• pp.189-195
• /
• 2005

This paper presents a new velocity estimation strategy for a non-salient permanent magnet synchronous motor drive without high frequency signal injection or special PWM pattern. This approach is based on the d-axis current regulator output voltage of the drive system, which contains the rotor position error information. The rotor velocity can be estimated through a rotor position tracking PI controller that controls the position error at zero. For zero and low speed operation, the PI gain of the rotor position tracking controller has a variable structure according to the estimated rotor velocity. Then, at zero speed, the rotor position and velocity have sluggish dynamics because the varying gains are very low in this region. In order to boost the bandwidth of the PI controller during zero speed, the loop recovery technique is applied to the control system. The PI tuning formulas are also derived by analyzing this control system by frequency domain specifications such as phase margin and bandwidth assignment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.9
• /
• pp.1913-1920
• /
• 2009

An intelligent accurate sun tracking controller for solar lighting system was developed. This controller can detect the faulty sensor and correct the error signal based on Principle Component Analysis theory. A fuzzy controller was developed to control the tracker by using the collected sensor signal for precise position control. Also a multiple range searching sensor module for sun tracking was designed. To show the validity of the developed system, some experiments in the field were illustrated.

• The Journal of Korea Robotics Society
• /
• v.2 no.3
• /
• pp.212-220
• /
• 2007

This paper proposes a method of avoiding obstacles and tracking a moving object continuously and simultaneously by using new concepts of virtual tow point and fuzzy danger factor for differential wheeled mobile robots. Since differential wheeled mobile robot has smaller degree of freedom to control and are non-holonomic systems, there exist multiple solutions (trajectories) to control and reach a target position. The paper proposes 'fuzzy danger factor' for obstacles avoidance, 'virtual tow point' to solve non-holonomic object tracking control problem for unique solution and three kinds of fuzzy logic controller. The fuzzy logic controller is policy decision controller with fuzzy danger factor to decide which controller's result is more valuable when the mobile robot is tracking a moving object with obstacles to be avoided.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.3
• /
• pp.308-317
• /
• 2006

To control the tip position of a flexible-link manipulator, a neural network (NN) controller is proposed in this paper. The dynamics error used to construct NN controller is derived based on output redefinition approach. Without the filtered tracking error, the proposed NN controller can still guarantee the closed-loop system uniformly asymptotically stable as well as NN weights bounded. Furthermore, the tracking error of desired trajectory can converge to zero with the proposed controller. For comparison an NN controller with filtered tracking error is also designed for the flexible-link manipulator. Finally, simulation studies are carried out to verify the theoretic results.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2473-2475
• /
• 2001

In trajectory tracking methods, the error values of current position and velocity are compensated to follow the given reference path and velocity. The path tracking for a wheeled mobile robot is treated in this paper. It is very difficult to implement stable trajectory tracking algorithms because mobile robots have kinematically non-holonomic constraints. For solving this problem, a velocity controller is presented in this paper. This velocity controller is designed by a PID controller which could be easily employed. In this case, velocity errors caused by system uncertainties or internal and external disturbances could exist. A neural network is used for compensating the velocity errors. Input variables of this neural network compensator are defined by differences between the velocities of the posture controller and the real velocities of the mobile robot. Simulation results show the effectiveness of the proposed controller.

• The Journal of Korea Robotics Society
• /
• v.9 no.1
• /
• pp.67-77
• /
• 2014

An electric motor is the one of the most important parts in robot systems, which mainly drives the wheel of mobile robots or the joint of manipulators. According to the requirement of motor performance, the controller type and parameters vary. For the wheel driving motors, a speed tracking controller is used, while a position tracking controller is required for the joint driving motors. Moreover, if the mechanical parameters are changed or a different motor is used, we might have to tune again the controller parameters. However, for the beginners who are not familiar about the controller design, it is hard to design pertinently. In this paper, we develop a nominal robust controller model for the velocity tracking of wheel driving motors and the position tracking of joint driving motors based on the disturbance observer (DOB) which can reject disturbances, modeling errors, and dynamic parameter variations, and propose the methodology for the determining the least control parameters. The proposed control system enables the beginners to easily construct a controller for the newly designed robot system. The purpose of this paper is not to develop a new controller theory, but to increase the user-friendliness. Finally, simulation and experimental verification have performed through the actual wheel and joint driving motors.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.270-275
• /
• 1993

In this paper, the arc welding robot controller using a touch sensor and a arc sensor is presented. The controller is composed of robot controller parts for moving torch, and arc welding controller for welding and tracking. In the controller, an compensated data is generated to control robot trajectory and seam tracking by the arc sensor function. The data is obtained by integration of arc current. Experimental results are presented confirming the controller performance.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.68-68
• /
• 2000

This paper presents a fuzzy modified PID controller that uses linear fuzzy inference method. In this structure, the proportional and derivative gains vary with the output of the system under control. 2-input PD type fuzzy controller is designed to obtain the varying gains. The proposed fuzzy PID structure maintains the same performance as the general-purpose linear PID controller, and enhances the tracking performance over a wide range of input. Numerical simulations and experimental results show the effectiveness of the fuzzy PID controller in comparison with the conventional PID controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.380-384
• /
• 1996

This paper represents an adaptive position controller with the disturbance observer for multi-axis servo system. The overall control system consists of three parts : the position controller, the disturbance observer with free parameters and cross-coupled controller which enhances contouring performance by reducing errors. Using two-degrees-of freedom conception, we design the command input response and the closed loop characteristics independently. The servo system can improve the closed loop characteristics without affecting the command input response. The characteristics of the closed loop system is improved by suppressing disturbance torque effectively with the disturbance observer. Moreover, the cross-coupled controller enhances tracking performance. Thus total position control performance is improved. Finally, the performance of the proposed controller shows that it improves the contouring performance along with the reference trajectory in the XY-table.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.6
• /
• pp.555-561
• /
• 2012

This paper describes the design of a fuzzy adaptive sliding mode controller for tracking control of robotic manipulators. The proposed controller incorporates a modified traditional sliding mode controller to drive the system state to a sliding surface and then keep the system state on this surface, and a fuzzy logic controller to accelerate the reaching phase. The stability of the control system is ensured by using Lyapunov theory. To verify the effectiveness of the proposed controller, computer simulation is conducted for a five-bar planar robotic manipulator. The simulation results show that the proposed controller can improve the reaching time and eliminate chattering of the control system at the same time.