• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.112-117
• /
• 2009

The new suspension, called ISU(In-arm suspension system) was developed for Infantry Fighting Vehicle. During vehicle field test, early failure of ISU's sealing system was occurred after driving the paved road. From the failure analysis, ISU's displacement data was obtained. In analysis of PSD data, track induced vibration which has high frequency and small amplitude characteristics, was dominant. Such track vibration would result in early seal failure because of friction increase and lack of lubrication. To simulate track vibration environment in laboratory, seals were tested under the condition of 20Hz, ${\pm}1$, ${\pm}2mm$ amplitude. The same type of seal failure occurred in vehicle test, was reproduced in the lab test under ${\pm}1mm$ amplitude. From the test results, the durability of improved seal was increased by 2.5 times compared with the previous one.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1659-1663
• /
• 2011

Precast concrete slab track is a track structure to be installed by transporting and assembling precast concrete slabs manufactured at the factory. This method can improve concrete quality, provide easy maintenance and reduce construction time, compared with in-situ concrete track. However, the concrete slabs being continuously connected in longitudinal direction, due to the temperature change between summer and winter, the openings at slab joints have occurred. Thus, in this study, to identify the cause of this opening of slab joint, the joint opening caused by temperature drop in the longitudinally continuous precast concrete slab track has been predicted using three-dimensional finite element analysis, and compared with field measurements. Based on the proven model, the slab joint opening, and the stress pattern of concrete slab and steel reinforcement according to concrete slab-base friction properties, concrete-reinforcement bond properties, and prestressing were analyzed.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1621-1626
• /
• 2003

This study deals with the heat transfer analysis on phase change optical disc with land/groove recording by means of numerical method. Finite difference time domain(FDTD) method was used to obtain the amount of absorption of light propagating inside disc and finite difference element(FEM) method was used to calculate the temperature distribution. The calculated results present the detailed information of recording characteristics on the phase change optical disc. The temperature profiles are quite different between the land track and the groove track. The recorded mark shape on land track is smaller and more elliptic than that on groove track. It is shown that the thermal problem to the neighboring track takes place due to secondary peaks. It is found that the different write strategy should be applied to land and groove recording, respectively.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.369-374
• /
• 2007

An active application of concrete track is being expected for the future construction of Korean railroad. For the successful concrete track construction and design in earthwork areas, the residual settlement should be reasonably estimated using the proper method. The concrete track is extremely vulnerable to the damage of residual settlement. However, at the transition areas such as bridge approach, differential settlement will likely occur due to difference of stiffness, poor drainage and poor ground treatment. The maintenance is very difficult for excessive settlement on existing line, it is need to constrain the residual settlement in step of design. In this paper, it is performed the analysis of the residual settlement measured data, test results and reference to understand the residual settlement behavior of concrete track roadbed

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.24-31
• /
• 1998

In this study, a procedure is presented for the dynamic analysis of a multibody tracked vehicle system. The planar vehicle model used in this investigation is assumed to consist of two kinematically decoupled subsystems. i.e., the chassis subsystem and track subsystem. The chassis subsystem includes the chassis frame, sprocket, idler and rollers, while the track subsystem is represented as a closed kinematic chain consisting of rigid links interconnected by revolute joints. The nonlinear contact force modules describing the interaction between track links, and sprocket, idler, rollers and ground will be developed.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.389-393
• /
• 2005

When the high-speed train running on the track, there is a speed limit which track distortion is unusually increased according to condition of track and roadbed. This speed limit is called critical velocity, and physical parameter value increased very greatly. These phenomenon happened as high-speed train were developed, studied regularly through TGV 100 running test in France. As research result until now, the main reason is soft roadbed's capacity. Wave propagation and track support capacity is varied by the site characteristics. This paper achieved theoretical examination about resonance band(speed and frequency) that occurred in roadbed on the base rock in point of geotechnical engineering. The examination of resonance divides with ground response analysis, critical band analysis by the shear wave velocity of roadbed, train critical speed through the ground stratum.

• Proceedings of the KSR Conference
• /
• 2002.05a
• /
• pp.250-255
• /
• 2002

The transition between bridge and earthwork often causes the problems of maintenance. The damages of the track on the transition area influence running safety of train and serviceability, increase the maintenance cost. Therefore it is very important to evaluate the dynamic responses of transition and take a efficient measure. In order to evaluate the dynamic behavior of track, the field estimations are performed at the transition area of a conventional line between bridge and earthwork. And the track system on the transition area numerically analyzed to evaluate the dynamic behavior of damaged track with void sleeper. The measured values and Analysis results such as wheel contact force, rail stress, displacement acceleration and track irregularity in the transition area show the dynamic forces are severe. So it is recommended that the transition area should be improved the rigidity by reinforcing the rail.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.71-78
• /
• 1998

Recently, continuous welded rail (CWR) track has been adopted for railway track structure of great advantages of reducing maintenance costs, and of increasing life time of track components and the comfort of passengers. But, in this case, a temperature or mechanical load will result in high stress and the track breakage or buckling may occur Especially when the CWR is laying on the bridge structure, the relative displacement of these structure can be increased and this results in the instability of track. In this paper, the main factors affect on the longitudinal rail force are discussed and the computer program is developed for the analysis of rail force considering the interactions with sub-structure.

• International Journal of Railway
• /
• v.2 no.4
• /
• pp.152-163
• /
• 2009

In this paper, the correlation between the accelerations measured at the track components and the parameters affecting the acceleration is analyzed. To do it, the accelerations of each track component such as rails, sleepers and ballast are measured in Kyong-Bu high-speed Line. The RMS values of the measured accelerations are calculated and the pad stiffness, the longitudinal irregularity, running velocity and the corrugation, are considered as the parameters affecting the acceleration. By using the linear regression, the correlation coefficients are calculated to analyze the relationship between the acceleration characteristics and the parameters. Also, the 1/3 Octave analysis is calculated to analyze the dominant frequency band of the accelerations of the track components.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.642-651
• /
• 2009

The history of excavator design is not long enough which still causes most of the design considerations to be focused on static analysis or simple functional improvement based on static analysis. However, the real forces experiencing on each component of excavator are highly transient and impulsive. Therefore, the prediction and the evaluation of the movement of the excavator by dynamic load in the early design stage through the dynamic transient analysis of the excavator and ensuring of design technique plays an importance role to reduce development-cost, shorten product-deliver, decrease vehicle-weight and optimize the system design. In this paper, Commercial software DADS and ANSYS help to develop the track model of the crawler type excavator, and to evaluate the performance and the dynamic characteristics of excavator with various simulations. For that reason, the track of crawler type excavator is modelled with DADS Track Vehicle Superelement, and the reaction forces on the track rollers were predicted through the driving simulation. Also, the upper frame and cabin vibration characteristics, at the low RPM idle state, were evaluated with engine rigid body modelling. And flexibility body effects were considered to determine the more accurate joint reaction forces and accelerations under the upper frame swing motion.