• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.1
• /
• pp.78-84
• /
• 2013

The primary objective of the current work is to develop efficient numerical code to assess the resistance performance of the twin hull form. Resistance performance for the two different twin hull forms with asymmetric and symmetric mono hull using developed code are evaluated. Numerical calculations and model tests have been compared to validate a developed code used in the current work. Comparison were carried out through sinkages of the bow and stern, trim angle and wave-making resistance. Comparative analysis regarding hydrodynamic characteristic of different twin hull forms is worthy of application in the hull form development stage.

• Ocean Systems Engineering
• /
• v.1 no.1
• /
• pp.17-28
• /
• 2011

The purpose of this paper is to demonstrate the efficacy of modeling a surface effect ship's air-cushion flexible seal utilizing a two-dimensional beam under steady state conditions. This effort is the initial phase of developing a more complex three-dimensional model of the air-seal-water fluid-structure interaction. The beam model incorporates the seal flexural rigidity and mass with large deformations while assuming linear elastic material response. The hydrodynamic pressure is derived utilizing the OpenFOAM computational fluid dynamic (CFD) solver for a given set of steady-state flow condition. The pressure distribution derived by the CFD solver is compared with the pressure required to deform the seal beam model. The air pressure, flow conditions and seal geometry are obtained from experimental analysis. The experimental data was derived from large-scale experimental tests utilizing a test apparatus of a canonical surface effect ship's flexible seal in a towing tank over a variety of test conditions.

• Journal of Ship and Ocean Technology
• /
• v.8 no.4
• /
• pp.1-9
• /
• 2004

High lifting devices used for control purposes have received much attention in the marine field. Hydrofoils for supporting the hull, roll stabilizer fins for developing the motion damping performance, rudders for maneuverability are the well-known devices. In the present study, the ability of the rudder with flap to produce high lift was analyzed. The boundary layer control, one of the flow control techniques, was adopted. Especially, to build the blown flap, a typical and representative type of a boundary layer control, a flapped rudder was designed and manufactured so that it could eject the water jet from the gap between the main foil and the flap to the flap surface tangentially. And it was tested in the towing tank. Simultaneously, to know the information about the 2-dimensional flow field, a fin model with similar characteristics as the rudder model applicable for the motion control was made and tested in the cavitation tunnel. In addition, local flow measurements were carried out to obtain physical information, for example, a surface pressure measurement and flow visualization around the flap. And CFD simulation was used to obtain information difficult to collect from the experiment about the 2-dimensional flow.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.1-8
• /
• 1999

Extensive resistance tests for a passenger boat(now in service at Chung-Ju lake) have been performed in a towing tank to investigate the effect of an artificial air cavity attached to the hull bottom on the reduction of the ship resistance. The attached air cavity has been observed at various air sully rates, from which we have determined a proper shape of an air supply device. In order to prevent the supplied air from leaking near the bilge of the ship, longitudinal barrier strips have been attached to both sides of the device. The investigation on their effectiveness reveals that a cascade system of the air supply device reduces the resistance of the ship furthermore. Energy saving of more than 10% is achieved at the design speed in spite of the additional power necessary for the air supply.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.1
• /
• pp.61-69
• /
• 2015

In the beginning of the 1990's, numerous shaft bearing damages, especially in aft stern tube bearing, were reported. The main reasons of bearing damages were estimated that hull deflections have been increased by more flexible hulls and propeller dynamic loads have not been considered in shaft alignment. After that time, studies to take into account hull deflections in shaft alignment have been actively carried out, but for the latter leave much to be desired. In this study, the effects of the propeller forces on the propeller shaft bearing have been investigated by estimating thrust eccentricity as reasonable as possible although some assumptions to simulate turning of ship were introduced. Three dimensional nominal wake to estimate thrust eccentricity have been calculated by using CFD analysis and model test in the towing tank. This study presents the procedure to estimate the propeller eccentric forces and their influence on the stern tube bearing for a container carrier. As a result, it has been found that the lateral propeller forces in turning condition should be considered in shaft alignment to prevent shaft bearing damages.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.3 s.153
• /
• pp.258-266
• /
• 2007

CFD calculations are performed for KRISO 3600TEU container ship(KCS) models with different Reynolds numbers. Numerical calculations of the turbulent flows with the free surface around KCS have been carried out at $Re=0.791{\times}106\;and\;Re=1.4{\times}107$ using a standard Fluent package. In both cases, Froude number is fixed with 0.26 and wave elevation is simulated by using the VOF method. The calculated results at $Re=1.4{\times}107\;and\;Re=0.791{\times}106$ are compared with the experiment data of KRISO towing tank test and RIMS CWC test, respectively. Boundary layer thickness and wake field shows Reynolds number differences. There are some changes in wave pattern behind transom stern.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2008.09a
• /
• pp.106-111
• /
• 2008

A hull form is 181K DWT Bulk Carrier, of which new design and hull form have been developed using CFD tools and model tests. The basic concept design of hull form has been carried out with considering the factors, which are a lot of influence of the wave and viscosity resistance. The considered factors of particular are LCB, DLWL shape, tern and stem profile, Cp-curve shape, etc. Numerical calculations are carried out in the initial design stage and experimental model tests are also carried out in towing tank of MOERI. The variation of the significantly effective characteristics is carried out to achieve optimized hull form. The results from numerical calculations and model test as well as the design procedures to obtain an optimized hull form resent in this paper.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.2
• /
• pp.723-735
• /
• 2019

This paper employs computational tools to investigate the cause of resistance reductions in calm water and waves of the sharp bow form compared to the blunt bow in 66,000 DWT bulk carriers. A more slender shape at the fore-shoulder without a bulbous bow is a prominent feature of the sharp bow. The blunt bow incorporates a bulbous shape. A two-phase unsteady Reynolds averaged Navier-Stokes equations have been solved; and a realizable k-ε model has been applied for the turbulent closure. The free-surface is obtained by solving a VOF equation. The computational results have been validated with model tests carried out at a towing tank. The pressure component of resistance in the sharp bow is reduced by 8.9% in calm water, and 6.4-12.7% in regular head waves. The frictional components of resistance in the sharp and blunt bows are largely the same.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.5
• /
• pp.429-434
• /
• 2014

The main objective of the present study is to elucidate a correlation between ship resistances from computational fluid dynamics (CFD) and brake horse powers (BHP) from towing tank in container carriers. The tests were conducted for a range of combinations of trim conditions and speeds. To achieve this goal, 295 cases of numerical simulation have been performed using Star-CCM+ which had been statistically verified to predict ship resistances (Lee & Lee, 2014). Based on the normal distribution of resistance errors in all cases of the 4 container carriers, the confidence interval of numerical error was estimated as [-2.33%,+2.42%] with 95% confidence. The correlation coefficients between the ship resistances of CFD and the brake horse powers of the experiments were higher than 0.93. As a result, the numerical calculation of ship resistances is able to be utilized in order to provide a quick guidance in selection of the optimum loading condition.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.121-127
• /
• 2011

As considerable interests in noise emission from a ship have been increased, the need for localization of noise sources of the marine propeller generating cavitation and singing noise is looming large. In many practical cases, cavitation and singing noise occur on a particular position of the certain blade of the propeller. It is so important to know the position of noise source correctly in order to eliminate or suppress unwanted noise. In this study, we develop "noise source localization technology" using TDOA method. Experimental measurements carried out at the circulating water channel and towing tank show that noise source can be clearly identified and localized using TDOA method.