• 한국공간구조학회논문집
• /
• 제24권1호
• /
• pp.89-98
• /
• 2024

In this study, we investigated the dynamic characteristics of three irregular building models to analyze the effectiveness of displacement response control with Tuned Mass Damper (TMD) installation in twisted irregular buildings. The three irregular models were developed with a fixed angle of twist per story at one degree, subjected to three historical seismic loads and resonant harmonic loads. By designing TMDs with linear and dashpot attributes, we varied the total mass ratio of the installed TMDs from 0.00625% to 1.0%, encompassing a total of 10 values. Two TMDs were installed at the center of the top story of the analysis model in both X and Y directions to evaluate displacement response control performance based on TMD installation. Our findings suggest that the top displacement response control performance was most effective when a 1.0% TMD was installed at the top layer of the analysis model.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.109-117
• /
• 2008

In this study, a method predicting the displacement responseof structures from the measured dynamic strain signal is proposed by using a mode decomposition technique. Dynamic loadings including wind and seismic loadings could be exerted to the bridge. In order to examine the bridge stability against these dynamic loadings, the prediction of displacement response is very important to evaluate bridge stability. Because it may be not easy for the displacement response to be acquired directly on site, an indirect method to predict the displacement response is needed. Thus, as an alternative for predicting the displacement response indirectly, the conversion of the measured strain signal into the displacement response is suggested, while the measured strain signal can be obtained using fiber optic Bragg-grating (FBG) sensors. To overcome such a problem, a mode decomposition technique was used in this study. The measured strain signal is decomposed into each modal component by using the empirical mode decomposition(EMD) as one of mode decomposition techniques. Then, the decomposed strain signals on each modal component are transformed into the modal displacement components. And the corresponding mode shapes can be also estimated by using the proper orthogonal decomposition(POD) from the measured strain signal. Thus, total displacement response could be predicted from combining the modal displacement components.

• 대한치과교정학회지
• /
• 제53권6호
• /
• pp.420-430
• /
• 2023

Objective: The purpose of this finite element method (FEM) study was to analyze the biomechanical differences and tooth displacement patterns according to the traction direction, methods, and sites for total distalization of the mandibular dentition using clear aligner treatment (CAT). Methods: A finite element analysis was performed on four FEM models using different traction methods (via a precision cut hook or button) and traction sites (mandibular canine or first premolar). A distalization force of 1.5 N was applied to the traction site by changing the direction from -30 to +30° to the occlusal plane. The initial tooth displacement and von Mises stress on the clear aligners were analyzed. Results: All CAT-based total distalization groups showed an overall trend of clockwise or counterclockwise rotation of the occlusal plane as the force direction varied. Mesiodistal tipping of individual teeth was more prominent than that of bodily movements. The initial displacement pattern of the mandibular teeth was more predominant based on the traction site than on the traction method. The elastic deformation of clear aligners is attributed to unintentional lingual tipping or extrusion of the mandibular anterior teeth. Conclusions: The initial tooth displacement can vary according to different distalization strategies for CAT-based total distalization. Discreet application and biomechanical understanding of traction sites and directions are necessary for appropriate mandibular total distalization.

• 대한치과보철학회지
• /
• 제45권1호
• /
• pp.1-11
• /
• 2007

Statement of problems: The concept of CR has also changed continuously.?In order to find out the factors that affect the centric slide, studies were carried out to compare the forms of wisdom teeth eruption, lateral movement, premature contact in CR, and anterior movement. Research and statistical methods were based on the report by the 1980 Korean dental association. Material and method: In our study, 403 dentists in their twenties and dentistry students who could understand CR and CO (and who did not receive occlusal, orthodontic treatment, without extreme caries and large prosthodontic care) were compared with the 25 year old results. A segment of line parallel to the upper incisor was marked on the lower incisor. When seen laterally, a line perpendicular to the occlusal plane was drawn on the foremost area of the upper incisor. This line was extended to the lower incisor and the two points (points at the lower and upper incisors) were used as reference points for the CO. After guiding the occlusion to the CR, two lines were marked by using the same method that was used for the CO. The point in which these lines meet became the reference point of CR occlusion Results and conclusions: Results of the experiment completed in 1980 show that all 307 research members had anterior-posterior and upper-lower displacement. Displacement measurements were $0.7{\pm}0.4mm$ for the anterior-posterior displacement, $0.99{\pm}0.50mm$ for the upper-lower displacement,0.18{\pm}0.31 mm for the lateral displacement, and $1.32{\pm}0.67mm$ for the total displacement. Results of the 2006 experiment show that all 409 research members had anterior-posterior and upper-lower displacement. The anterior-posterior displacement was $1.12{\pm}0.86mm$, the upper-lower displacement was $1.02{\pm}0.71mm$, the lateral displacement was $0.61{\pm}0.56mm$, and the total displacement was $1.80{\pm}0.99mm$. No specific differences were found between each group when comparing displacement according to the forms of wisdom teeth eruption. Since 1980, the percentage of unerupted teeth has increased from 35.16% (111/307 people) to 57.5% (236/409 people). Westernization of the Korean cranial form and intraoral structure has brought about these results. In our experiment, 26.7% (109/409 people) of the subjects were cuspid guided, while 7.3% (30/409 people) were mutually guided. No specific differences were found in the amount of displacement between the two groups. Only the subjects with anteriors coming in contact made up the largest percentage group (42.3%, 173/409 people) in our study. No specific differences were found between each group.

• Structural Engineering and Mechanics
• /
• 제29권6호
• /
• pp.659-671
• /
• 2008

A procedure to analyse the space frame structure fixed at base as well as resting on sliding bearing using total or absolute displacement in dynamic equation is developed. In the present method, the effect of ground acceleration is not considered as equivalent force. Instead, the ground acceleration is considered as a known value in the acceleration vector at degree of freedom corresponding to base of the structure when the structure is in non-sliding phase. When the structure is in sliding phase, only a force equal to the maximum frictional resistance is applied at base. Also, in this method, the stiffness matrix, mass matrix and the damping matrix will not change when the structure enters from one phase to another. The results obtained from the present method using absolute displacement approach are compared with the results obtained from the analysis of structure using relative displacement approach. The applicability of the analysis is also demonstrated to obtain the response of the structure resting on sliding bearing with restoring force device.

• 치과방사선
• /
• 제28권1호
• /
• pp.155-169
• /
• 1998

The purpose of this study was to prove the relationship between arthrographic and clinical features in temporomandibular joint disorders. In order to carry out this study, ninety-eight arthrographic examinations of temporomandibular joints were performed on eighty-two patients who had the temporomandibular joint disorders. As the arthrographic examination, the cases were classified in three groups, disk displacement with reduction, disk displacement without reduction, within normal limit. After this, the cases were clinically examined, and the results were compared and analyzed in each other group. The obtained results were as follows; 1. As the classification by arthrographic examination, three groups (disc displacement with reduction, disc displacement without reduction, within normal limit) were 41 ％, 54％, 5％ of total cases in this study, respectively. 2. The third decade(65％) was most frequent in this study. The average age of each group (disc displacement with reduction, disc displacement without reduction, within normal limit) was 24, 28, 21, and disc displacement without reduction group was higher than any other group. 3. In the chief complaint, pain was the most frequent in all three groups. Joint sound was also frequent in disc displacement with reduction group, but in disc displacement without reduction group, limitation of mouth opening was more frequent. 4. Of the various pain, the movement pain was most frequent ( 61 ％) in this study. In joint sound, click(63％) was the most frequent in disc displacement with reduction group, but sound history(42％) and no sound (31 ％) were more frequent in disc displacement without reduction group. 5. The average maximum opening of each group (disc displacement with reduction, disc displacement without reduction, within normal limit) was 44mm, 32.9mm, 44mm, and disc displacement without reduction group was less than any other group. 6. The masticatory disturbance of each group (disc displacement with reduction, disc displacement without reduction, within normal limit) was 53％, 79％, 40％, and the trauma history of each group was 50％, 40％,60％.

• 한국가스학회지
• /
• 제19권4호
• /
• pp.55-61
• /
• 2015

본 연구에서는 여러 가지의 절단면 형상과 하중지지 용량을 높이기 위해 원판을 설치한 중공롤러의 변위거동 특성을 유한요소법으로 해석하였다. FEM 해석결과에 의하면, 중공롤러의 절단면 형상은 외측튜브, 중간튜브, 내측튜브와 이들 튜브들 사이를 연결하기 위해 X형 또는 Y형 컬럼을 설치한 경우는 중공롤러의 중간부에서 발생하는 최대 변위량을 줄여주는 효과가 있다. 여기에 중공롤러의 중간부 두께를 30~40mm 갖는 원판을 설치할 경우는 중공롤러의 최대 변위량을 줄이는데 효과가 크다는 해석결과를 제시하였다. 본 연구에서는 원통롤러의 전체 중량에 연계된 최대 변위량 비율을 고찰한 최적설계 데이터를 제하였다. FEM 해석결과에 의하면, 중공롤러에서 발생하는 최대 변위량과 전체 중량의 비율을 줄인 설계모델로는 4, 5와 6번을 추천할 수 있다.

• 한국산학기술학회논문지
• /
• 제21권4호
• /
• pp.582-587
• /
• 2020

최근 기상이변으로 인한 재해가 전 세계적으로 증가하고 있으며, 세계적으로 재해로 인한 피해가 커지고 있어 국내에서도 지진, 태풍, 지반침하 등 재해에 대한 관심이 높아지고 있다. 우리나라는 재난관리에 의한 특별법을 제정하고, 장대교량 및 초고층 복합건축물은 시설물의 변위상태 측정을 위해 정밀센서와 관련 시스템 등을 구축하여 개별 시설물 단위의 모니터링 시스템을 구축하도록 하고 있다. 하지만 사면이나 노천광산, 중, 소규모의 구조물에 대해서는 기상, 측정방법, 비용, 상시 모니터링의 어려움으로 인해 실시간 모니터링 시스템의 적용이 미흡한 실정이다. 이에 본 연구에서는 토털스테이션을 활용한 변위 모니터링 방안을 연구하고, 실험을 통해 적용성을 제시하고자 하였다. 연구 결과 토털스테이션을 이용하여 지형이나 구조물의 변위를 측정할 수 있는 모니터링 시스템의 개념과 운영 흐름을 제시하였다. 모니터링 시스템은 현장상황에 따라 장비를 설치할 수 있도록 장비의 위치 및 운용 방식을 선택하고, 대상물에 대한 관측 횟수, 주기, 관측범위 등을 설정할 수 있도록 하였다. 모니터링 시스템에 대한 실험을 통해 5mm 이내의 정밀도로 측점을 모니터링 하였으며, 토털스테이션을 이용한 대상물의 변위 모니터링이 가능함을 제시하였다. 향후, 추가적인 연구를 통해 실제 사면이나 구조물에 대한 모니터링의 적용성을 제시할 수 있을 것으로 기대된다.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.36-40
• /
• 2008

This study is analyzed by the simulation of automotive steering system. The maximum equivalent stress of $2.2418{\times}109Pa$ and the maximum total displacement of 0.014929m are shown at the universal joint and its lower part respectively. As the minimum cycle of 34.047 is shown at the universal joint in case of fatigue analysis, it is possible to have greatest damage at this part. In case of natural frequency analysis at vibration, its frequency of 47 to 59Hz is occurred generally. The maximum total displacement of 0.5m is shown at handle on the natural frequency of 57 to 58Hz. And the displacement over 2m is shown at the lower part of universal joint on the natural frequency of 58 to 59Hz. As the basis of the simulation analysis of steering system, passenger's comfort of car body can be improved in the design of practical part and the design effect necessary to safe driving can be promoted.

• 대한기계학회논문집A
• /
• 제30권10호
• /
• pp.1219-1226
• /
• 2006

The ASTM test standard recommends the use of the compact tension specimen for creep crack growth rates measurement. In the creep crack growth rate test, the displacement rate due to creep is obtained by subtracting the contribution of elastic and plastic components from the total load line displacement rate based on displacement partitioning method fur determining $C^*-integral$, which involves Ramberg-Osgood (R-O) fitting procedures. This paper investigates the effect of the R-O fitting procedures on plastic displacement rate estimates in creep crack growth testing, via detailed two-dimensional and three-dimensional finite element analyses of the standard compact tension specimen. Four different R-O fitting procedures are considered; (i) fitting the entire true stress-strain data up to the ultimate tensile strength, (ii) fitting the true stress-strain data from 0.1% strain to 0.8 of the true ultimate strain, (iii) fitting the true stress-strain data only up to 5% strain, and (iv) fitting the engineering stress-strain data. It is found that the last two procedures provide reasonably accurate plastic displacement rates and thus should be recommended in creep crack growth testing. Moreover, several advantages of fitting the engineering stress-strain data over fitting the true stress-strain data only up to 5% strain are discussed.