• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.732-737
• /
• 2016

Using the pyrolyzed carbon black (PCB) from waste tires, the performance of 13 mm dense-graded hot mix asphalt was evaluated. The Marshall mix design was carried out and the measured optimal asphalt content was 5.8%. The impact resonant test was conducted to obtain the elastic modulus and damping ratio of the hot mix asphalt. The elastic modulus of HMA increased with increasing amount of PCB. On the other hand, there was no significant change in the damping ratio. The Marshall mix design, indirect tensile test, permanent deformation test, and program analysis were carried out. The strength ratio of the PCB modified asphalt mixtures was within 10%. More 10% of PCB was not good for the permanent deformation of hot mix asphalt. From the pavement design program, the use of 5% PCB in hot mix asphalt showed a decrease in the top-down crack, bottom-up crack, and permanent deformation. Judging from the limited test and analysis, the use of 5% PCB is good for enhancing the pavement performance.

• Smart Media Journal
• /
• v.3 no.4
• /
• pp.9-15
• /
• 2014

A virtual platform models a processor core and the peripheral devices constituting the SoC in software. Major companies utilize a variety of platforms for product development with optimal SW+SoC integrated system architecture design and IP reuse based Top-Down design flow using a virtual platform. In this paper, we propose a virtual platform based on OpenRISC, an open source RISC based core. The proposed virtual platform supports high speed emulation of approximately 20 MIPS using DBT (Dynamic Binary Translation).

• Journal of the Korea Society of Computer and Information
• /
• v.3 no.4
• /
• pp.63-69
• /
• 1998

The area optimization of the power distribution network is an important problem in the layout design of VLSI systems. In this paper we propose noval methods to solve the problem of designing minimal area power distribution nets, while satisfying voltage drop and electromigration constraints. We propose two novel greedy heuristics for power net design-one based on bottom-up tree construction using greedy merging and the other based on top-down linearly separable partitioning.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.50-59
• /
• 2007

[ $0.18-{\mu}m$ ] CMOS 1.2-V 2nd-order ${\Sigma}{\Delta}$ modulator with full-feedforward topology is designed. Using full-feedforward topology makes op-amp performance requirements much less stringent, therefore it has been adopted as a good candidate for low-voltage low-power applications throughout the world. Also, ${\Sigma}{\Delta}$ modulator is designed with top-down design approach, therefore various nonideal effects of op-amp are modeled in this paper.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.9
• /
• pp.5-12
• /
• 2013

In this study, each top-down load test and bi-directional load test has been performed on the 480mm diameter of two rock socketed drilled shafts, which are located next to each other, and the results have been compared. The result shows that the settlement from the equivalent load-settlement curve of bi-directional load test is smaller than one from top-down load test, because elastic is not considered in equivalent load-settlement curve of bi-directional load test. Therefore elastic shortening should be considered to obtain appropriate equivalent load-settlement curve. Three existing methods used to obtain equivalent load-settlement curve with consideration of elastic shortening has been compared with the result of top-down load test. The result shows that those existing methods are sufficiently applicable to the design. In addition, result of comparison between top-down load test and bi-directional load test shows that bi-directional load test was found to overestimate bearing capacity because it does not consider pile body failure.

• Nuclear Engineering and Technology
• /
• v.53 no.3
• /
• pp.793-803
• /
• 2021

The small PWR has been paid more and more attention due to its diversity of application and flexibility in the site selection. However, the large core power density, the small containment space and the rapid accident progress characteristics make it difficult to control the containment pressure like the traditional PWR during the LOCA. The pressure suppression system has been used by the BWR since the early design, which is a suitable technique that can be applied to the small PWR. Since the configuration and operating conditions are different from the BWR, the pressure suppression system should be redesigned for the small PWR. Conducting the experiments on the scale down test facility is a good choice to reproduce the prototypical phenomena in the test facility, which is both economical and reasonable. A systematic scaling method referring to the H2TS method was proposed to determine the geometrical and thermohydraulic parameters of the pressure suppression containment response test facility for the small PWR conceptual design. The containment and the pressure suppression system related thermohydraulic phenomena were analyzed with top-down and bottom-up scaling methods. A set of the scaling criteria were obtained, through which the main parameters of the test facility can be determined.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.4
• /
• pp.367-378
• /
• 2023

With the recent development of computer-aided design-computer-aided manufacturing technology and 3D printing technology, and the introduction of various digital techniques, the accuracy and efficiency of top-down definitive prosthetic restoration are increasing. In this clinical case, stable occlusion support was obtained through the placement of a total of 9 maxillary and mandibular posterior implants in patient with anterior-posterior crossed occlusion. The edentulous area of the maxillary anterior teeth, which showed a tendency of high resorption of the residual alveolar bone, was restored with a Kennedy Class IV implant assisted removable partial denture to restore soft tissue esthetics. Computed tomography guided surgery was used to place implants in the planned position, double scan technique was used to reflect the stabilized occlusion in the interim restoration stage to the definitive prostheses, and metal 3D printing was used to manufacture the coping and framework. This clinical case reports that efficient and predictable top-down full mouth rehabilitation was achieved using various digital technologies and techniques.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.12 no.2
• /
• pp.1-20
• /
• 2010

This thesis is about "manggon" that holds down man's top knot hair and its accessaries "pungjam", "kwanja". manggon was seen first time in the mural of Donwhang kae won chon bo during T'ang period (713-756). The "Tu Aek Ra" manggon shown in this mural would be the origin and beginning of maggon's usage. Also the "Sha" that was placed on top of the hair for decoration purpose is believed to be a former form of "manggon" Before the short hair cut was enforced, wearing the "kwan"(head gear) was considered as an impotant etiguette. Thus the head gear was treasured and the manggon which was the most essential piece to cover down the hair before to put on the head gear was regarded as the most important piece. However, since the manggon was tied very tightly around the forehead, manggon caused some sickness. From my private collections of man's head gears and ornament, 121 items were selected and used for analysis and the followings were found: 1. Pungjam was divided into 8 categories according to its shape and a research was made on its unique structural characteristic on each categories. 2. Kwanja's material and design that were used are all in accordance to the historical recordings.

• Journal of Ocean Engineering and Technology
• /
• v.12 no.3 s.29
• /
• pp.86-95
• /
• 1998

CAD/CAM program developers have made substantial progress in enabling engineers to design, analyze, visualize, visualize, and simulate the performance of structures and systems. Many researchers, however, agree that there is still a way to go before the existing commercial computer software can be used in ship structural analysis to their full potential as solvers which can identify opportunities to reduce man-hours and cut costs. CAD systems used for these works in ship yards are general-purposed and not custom-tailored for ship structures, which force end-users to do tiresome and routine works. The new preprocessor "MeshGen" announced in this study can load several ship types and user-friendly generate their FE meshes employing the object-oriented approach based on the parametric and top-down design. Also "MeshGen" reduces dramatically the time required to prepare CAD models under window-based environments on desktop personal computers and makes it much easier and faster for end-users to change topology and material properties.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.5
• /
• pp.889-898
• /
• 2022

In this study, sand casting process was applied to manufacture a large aluminum turbo-type fan used for tank powerpack. To apply the sand casting method, the turbo fan was reverse engineered, and after designing three gating systems, the optimal gating system design was selected by performing casting simulation. In the case of the bottom up-gating system, there is a significant temperature loss of the molten alloy during blade filling. When the molten alloy is completely filled into the sand mold, the blade upper tip and front shroud are below the liquidus temperature. In the case of the top down-gating system, molten alloy scattering occurs, but the temperature loss while the blade is filled is smaller than that of the bottom up type. And after the inflow of molten alloy into the mold is completed, the blade upper tip and front shroud are higher than the liquidus temperature. A sand mold was manufactured with the top down-gating system and the casting process was performed. The fan was made perfectly in appearance without any unfilled parts.