• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.3
• /
• pp.147-153
• /
• 2018

Jamming countermeasures are used to decrease or prevent the impact of intentional jamming applied to degrade the quality of information provided by a global navigation satellite system (GNSS) receiver. The maximum performance of jamming countermeasure can be obtained only when a proper technique is applied according to the type of jammer. This paper suggests a jamming identification technique for providing information regarding the type of jamming. The center frequency and bandwidth of jammer signal are inconsistent and may change according to time, and thus a spectral correlation function and wavelet coherence were considered in order to analyze the signal in the time and frequency space. Because the two characteristics derive different analysis results, two different identification techniques were suggested and the performances thereof were analyzed. Numerical results show that the two identification techniques have relative advantages and disadvantages as to time consumed and performance. The suggested methods can sufficiently identify the jammer before the GNSS receiver becomes inoperable because of jamming.

• Journal of the Institute of Convergence Signal Processing
• /
• v.6 no.3
• /
• pp.143-147
• /
• 2005

Monitoring and diagnosis of the operating machines are very important for safety operation and maintenance in the industrial fields. These machines are most rotating machines and the diagnosis of the machines has been researched for long time. We can easily see the faulted signal of the rotating machines from the changes of the signals in frequency. The Linear Predictive Coding(LPC) is introduced for signal analysis in frequency domain. In this paper, we propose fault detection and diagnosis method using the Linear Predictive Coding(LPC) and residual signal energy. We applied our method to the induction motors depending on various status of faulted condition and could obtain good results.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.4
• /
• pp.264-273
• /
• 2015

This presentation describes an experimental approach for the detection of cavitation in hydraulic machines by use of ultrasonic signal analysis. Instead of using the high frequency pulses (typically 1MHz) only for transit time measurement different other signal characteristics are extracted from the individual signals and its correlation function with reference signals in order to gain knowledge of the water conditions. As the pulse repetition rate is high (typically 100Hz), statistical parameters can be extracted of the signals. The idea is to find patterns in the parameters by a classifier that can distinguish between the different water states. This classification scheme has been applied to different cavitation sections: a sphere in a water flow in circular tube at the HSLU in Lucerne, a NACA profile in a cavitation tunnel and two Francis model test turbines all at LMH in Lausanne. From the signal raw data several statistical parameters in the time and frequency domain as well as from the correlation function with reference signals have been determined. As classifiers two methods were used: neural feed forward networks and decision trees. For both classification methods realizations with lowest complexity as possible are of special interest. It is shown that two to three signal characteristics, two from the signal itself and one from the correlation function are in many cases sufficient for the detection capability. The final goal is to combine these results with operating point, vibration, acoustic emission and dynamic pressure information such that a distinction between dangerous and not dangerous cavitation is possible.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.1
• /
• pp.133-140
• /
• 2001

Recently, to assure the integrity of a structural components such as piping pressure vessels and thinning structure, Lamb wave inspection technique has been used in material evaluation. It is very important to select the optimal Lamb wave mode and to analyze the signal accurately because of its unique dispersion properties grnerating several modes within the speci-men. It this study, the feasibility of material evaluation applications using wavelet analysis of Lamb wave has been veir-fied experimentally. These results show as follows; 1)dispersion characteristic of each mode in dispersion curve is demon-strated that A0 mode propagating material surface is useful mode having the lest energy loss and not sensitive to surface condition. 2) it can be detected even the micro defect ($1\times2mm$) fabricated in ultrasonic probe flaw distance (290mm) to axis direction. 3) the wavelet transform which is called "time-frequency analysis" shows the Lamb wave propagation due to the change of materials characterization can be evaluated at each frequency and experimental group velocity of Lamb wave agrees quite well with that of simulated dispersion curve.ion curve.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.4
• /
• pp.271-276
• /
• 2021

Arc fault detector based on multilevel DWT with analysis of high-frequency noise components over 100 kHz is proposed in this study to improve the performance in detecting serial arcs and distinguishing them from inverter noise in PV systems. PV inverters generally operate at a frequency range of 20-50 kHz for switching operation and maximum power tracking control, and the effect of these frequency components on the signal for arc detection leads to negative arc detection. High-speed ADC and multilevel DWT are used in this study to analyze frequency components above 100 kHz. Such high frequency components are less influenced by inverter noise and utilized to detect as well as separate DC series arc from inverter noise. Arc detectors identify the input current of PV inverters using a Rogowski coil. The sensed signal is filtered, amplified, and used in 800kSPS ADC and DWT analysis and arc occurrence determination in DSP. An arc detection simulation facility in UL1699B was constructed and AFD tests the proposed detector were conducted to verify the performance of arc detection and performance of distinction of the negative arc. The satisfactory performance of the arc detector meets the standard of arc detection and extinguishing time of UL1699B with an arc detection time of approximately 0.11 seconds.

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1310-1323
• /
• 2023

A reactor coolant pump (RCP) is essential for transporting coolant in the primary loop of pressurized water reactors. In the advanced passive reactor, the absence of a long pipeline between the steam generator and RCP serves as a transition section, resulting in a non-uniform flow field at the pump inlet. Therefore, the characteristics of the pump should be investigated under non-uniform flow to determine its influence on the pump. In this study, the pressure pulsation characteristics were examined in the time and frequency domains, and the sources of low-frequency and high-amplitude signals were analyzed using wavelet coherence analysis and numerical simulation. From computational fluid dynamics (CFD) results, non-uniform inflow has a great effect on the flow structures in the pump's inlet. The pressure pulsation in the pump at the rated flow increased by 78-128.7% under the non-uniform inflow condition in comparison with that observed under the uniform inflow condition. Furthermore, a low-frequency signal with a high amplitude was observed, whose energy increased significantly under non-uniform flow. The wavelet coherence and CFD analysis verified that the source of this signal was the low-frequency pulsating vortex under the steam generator.

• Journal of KSNVE
• /
• v.6 no.3
• /
• pp.341-347
• /
• 1996

Vibration analysis is one of the most powerful tools available for the detection and isolation of incipient faults in mechanical systems. The methods of vibration analysis in use today and under continuous study are broad band vibration monitoring, time domain analysis, and frequency domain analysis. In recent years, great interest has been generated concerning the use of time- frequency repesentation and its application for a machinery diagnostics and condition monitoring system. The objective of the study described in this paper was to develop a new diagnostic tool for the rotating machinery. This paper introduces a new time frequency representation. Directional Winger-Ville Distribution, which analyese the time-frequency structure of the rotating machinery vibration.

• Journal of the Korean Institute of Navigation
• /
• v.22 no.1
• /
• pp.15-22
• /
• 1998

In this paper, discontinuity parts in microstrip line with $\lambda$/4 open stub and one in crank type have been anlayzed by using FDTD(Finite-Difference Time-Domain) analysis method. The noise components, in this case, are occred at the discontinuites of the given microstrip lines, the complex poles were extracted by the analysis using GPOF (Generalized Pencil-of Function) method from electric field of time domain. It has, then, been found that the noise level and the noise frequency components included in signal could be derived.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.3
• /
• pp.84-90
• /
• 2014

The partial discharge of Cast-resin Transformer has a difficulty to be analyzed, because it is an abnormal condition signal of which stochastic characteristics varies with time variance. In this study, background noise coming from the outside of the cast-resin transformers through ground wire can be removed and only a discharge signal of which defects are simulated can be obtained, using the wavelet transform method, which is a time-frequency domain analysis technique. As a result, it was confirmed that de-noising using the SWT technique is the best efficient among three methods of the wavelet transform techniques.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.3
• /
• pp.71-75
• /
• 2008

This paper illustrates haw $Y_2O_3$ contributes to crack-healing strengths as a function of crack-healing temperature and the additive amount. In investigating mechanical properties, the indentation fracture method is very simple and useful, but careful attention must be paid to the statistical data processing because data may be scattered excessively, especially for brittle materials. To estimate accurate AE signal properties we applied the useful time-frequency method with a discrete wavelet analysis algorithm. In experiments, three kinds of specimens were prepared. After the specimens were indented by a Vickers indentor, they were heat-treated and crack-healed to evaluate bending strength and the AE signal. With higher amounts of the additive powder, as 1, 3, or 5% wt. of $Y_2O_3$, the concentrative tendency of dominant frequency trended toward lower frequency groups. The $Al_2O_3$ ceramic with 3% wt. of $Y_2O_3$ was judged most suitable because it demonstrated superior crack-healing ability and relative concentration on the highest frequency group.