• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12A
• /
• pp.2000-2011
• /
• 2001

In this Paper, we convert conventional low speed(1x, 6x) DVD systems designed by analog PLL(Phase Locked Loop) into digital PLL to operate at high speed systems flexibly, and present optimal DPLL model in high speed(20x) DVD systems. Especially, we focused on the design of DPLL that can overcome channel effects such as bulk delay, sampling clock frequency offset and asymmetry phenomenon in high speed DVD systems. First, the modified Early-Late timing error detector as digital timing recovery scheme is proposed. And the four-sampled compensation algorithm using zero crossing point as asymmetry compensator is designed to achieve high speed operation and strong reliability. We show that the proposed timing recovery algorithm provides enhanced performances in jitter valiance and SNR margin by 4 times and 3dB respectively. Also, the new four-sampled zero crossing asymmetry compensation algorithm provides 34% improvement of jitter performance, 50% reduction of compensation time and 2.0dB gain of SNR compared with other algorithms. Finally, the proposed systems combined with asymmetry compensator and DPLL are shown to provide improved performance of about 0.4dB, 2dB over the existing schemes by BER evaluation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.9
• /
• pp.1364-1372
• /
• 2017

In this paper, a problem of event-triggered model predictive control is investigated for continuous-time Takagi-Sugeno (T-S) fuzzy systems with input quantization. To efficiently utilize network resources, event-trigger is employed, which transmits limited signals satisfying the condition that the measurement of errors is over the ratio of a certain level. Considering sampling and quantization, continuous Takagi-Sugeno (T-S) fuzzy systems are regarded as a sector bounded continuous-time T-S fuzzy systems with input delay. Then, a model predictive controller (MPC) based on parallel distributed compensation (PDC) is designed to optimally stabilize the closed loop systems. The proposed MPC optimize the objective function over infinite horizon, which can be easily calculated and implemented solving linear matrix inequalities (LMIs) for every event-triggered time. The validity and effectiveness are shown that the event triggered MPC can stabilize well the systems with even smaller average sampling rate and limited actuator signal guaranteeing optimal performances through the numerical example.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.5
• /
• pp.358-363
• /
• 2019

If the EOIR equipment mounted on an unmanned aircraft transmits images and receives commands through a data link, there may be delays in data transmission depending on the transmission path of the data and the conditions of the ground equipment or wireless network. This increases the possibility of initial target LOCK-ON failure due to the difference between the time when the received image is viewed and the time when the image is taken. Therefore, this paper proposed a way to use frame indexes to synchronize with images, and to increase the success of target tracking by adding frame indexes to commands from the ground station.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.3
• /
• pp.20-25
• /
• 2009

The quench detection system of the KSTAR (Korea Superconducting Tokamak Advanced Research) primarily uses the resistive voltage measurement due to a quench. This method is to detect the resistive voltage generated by a quench, which is continuously maintained above the preset voltage threshold for a given holding time. As the KSTAR PF (Poloidal Field) coils are operated in the pulse current mode, the large inductive voltages are generated. Therefore the voltage threshold and the quench holding time should be determined by considering both the inductive voltages measured during the operation, and the maximum conductor temperature rise through the quench analysis. In this paper, the compensation methods for minimizing the inductive voltages are presented for the KSTAR PF coils. The quench hot spot analysis of the PF coils was carried out by the analytical and numerical methods for determining the proper values of the quench voltage threshold and the allowable quench protection delay time.

• Journal of Advanced Navigation Technology
• /
• v.14 no.5
• /
• pp.625-631
• /
• 2010

In this paper, robustness performance of SNUR message is compared with those of existing ones, RTCM(Radio Technical Commission for Maritime Services) v2 MT(Message Type) 18/19 and MT 20/21 under a poor broadcast condition such as temporary data loss or disconnection We defined the temp oral data loss as 2 second delay and reconnection after disconnection as 7 second latency, and then evaluated its robustness for each latency case by double differentiating the observables. Our result shows that SNUR protocol method can reduce the latency error of the existing RTCM messages by 30~60%. Moreover, a rover using SNUR message, whose latency error is bounded within 1/4 L1 wave length, can figure out its own fixed position continuously in spite of 7 second disconnection, while the other using RTCM message, whose error is larger than half wave length, cannot keep its previous fixed solution.

• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.2
• /
• pp.107-112
• /
• 2011

Several developed countries have been developing their own satellite navigation systems, such as Europe's Galileo, China's BEIDOU, and Japan's QZSS, to cope with clock errors and signal vulnerabilities of GPS. In addition, modernization of Loran, eLoran, for GPS backup has been conducted. In Korea, a dependent navigation system has been required and for GPS backup, the need for utilization of time synchronization infrastructure through the modernization of Loran has been raised. Loran signal uses 100Khz groundwave. A significant factor limiting the ranging accuracy of the Loran signal is the ASF arising from the fact that the groundwave signal is likely to propagate over paths of varying conductivity and topography. Thus, an ASF compensation method is very important for Loran and eLoran navigation. This paper introduces the propagation delay model and then compares and analyzes the estimations from the propagation delay model and measured ASFs.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.227-237
• /
• 2016

A novel digital current control strategy for digitally controlled DC-DC switching converters, referred to as Adjacent Cycle Sampling (ACS), is proposed in this paper. For the ACS current control strategy, the available time interval from sampling the current to updating the duty ratio, is approximately one switching cycle. In addition, it is independent of the duty ratio. As a result, the contradiction between the processing speed of the hardware and the transient response speed can be effectively relaxed by using the ACS current control strategy. For digitally controlled buck DC-DC switching converters with trailing-edge modulation, digital current control algorithms with the ACS control strategy are derived for three different control objectives. These objectives are the valley, average, and peak inductor currents. In addition, the sub-harmonic oscillations of the above current control algorithms are analyzed and eliminated by using the digital slope compensation (DSC) method. Experimental results based on a FPGA are given, which verify the theoretical analysis results very well. It can be concluded that the ACS control has a faster transient response speed than the time delay control, and that its requirements for hardware processing speed can be reduced when compared with the deadbeat control. Therefore, it promises to be one of the key technologies for high-frequency DC-DC switching converters.

• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.27-33
• /
• 2016

The heat recovery system that was applied in this study, is the energy-saving type that can produce the maximum cooling capacity less power in use. In order to have a more precise control function the temperature and humidity of the constant temperature and humidity machine, control algorithm is applied to designed a fuzzy PID controller, and the outside air compensation device (air-cooled) demonstrated excellent ability to dehumidify the moisture, $-20^{\circ}C$ in winter. High efficiency and the low-noise type sirocco fan operate quitely and designed to fit the bottom-up and top-down in accordance with the characteristics of equipment. as a result of experiment data, the conversion efficiency is 95% or more, power recovery time is within 5sec, stop delay time is within 30sec, pump down time is 10sec, pump delay time is 5sec, heating delay time is 5sec, temperature deviation is ${\pm}2^{\circ}C$ (cooling deviation: $2^{\circ}C$, Heating deviation : $2^{\circ}C$), humidity deviation is a ${\pm}5%$ (humidification deviation 3.0%, dehumidification deviation 3.0%). Recently, ubiquitous technology is important. so, the constant temperature and humidity machine designed to be able to remotely control to via the mobile phone, and more scalable to support MMI software and automatic interface. Further, the life of the parts and equipment is extended by the failure.

• Journal of Biomedical Engineering Research
• /
• v.23 no.3
• /
• pp.243-251
• /
• 2002

Synthetic zinc wave employs Pulsed plane wave as transmit beam with linear time delay curve. The received echoes in different transmit directions at different transmit times are superposed at imaging Points with Proper time delay compensation using synthetic focusing scheme. This scheme. which uses full aperture in transmit, obtains a high SNR image, and also features high lateral resolution by using two way dynamic focusing at all imaging depths. In this Paper, we consider the Problems in realization of synthetic zinc wave. Also. we have applied the scheme to obtain phantom and in-vivo images using a linear array of 5 MHz. In phantom test. experimental images show high resolution over a more extended imaging depth than conventional fixed Point transmit and receive dynamic focusing schemes In-vivo images show that the resolution could not overcome conventional focusing systems because of motion blurring and(or) aberration of tissue. but the frame rate tan be increased by a factor of more than 5 compared to conventional focusing schemes. with competitive resolution at all imaging depths .

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.2
• /
• pp.269-278
• /
• 2016

In order to maintain customer voltages within allowable limit($220{\pm}13V$) as much as possible, tap operation strategy of SVR(Step Voltage Regulator) installed in distribution system is very important, considering the scheduled delay time(30 sec) of SVR. However, the compensation of BESS(Battery Energy Storage System) during the delay time of SVR is being required because the customer voltages in distribution system interconnected with PV(Photovoltaic) system have a difficultly to be kept within allowable limit. Therefore, this paper presents the optimal voltage stabilization method in distribution system by using coordination operation algorithm between BESS and SVR. It is confirmed that customer voltage in distribution system can be maintained within allowable limit($220{\pm}13V$).