• Journal of Positioning, Navigation, and Timing
• /
• 제10권4호
• /
• pp.253-262
• /
• 2021

Global Navigation Satellite Systems (GNSS) based precise positioning using Real Time Kinematic (RTK) technique has been proposed as an enabler of the formation operation of moving vehicles. In RTK methods, the integer ambiguity of GNSS carrier phase measurements must be resolved. Although there have been many proposed algorithms for the integer ambiguity resolution, the widelane combination of carrier phase measurements and LAMBDA methods have gained the most popularity in literatures when dual frequency GNSS measurements were used. In this paper, we evaluated five alternative methods to determine relative positions of moving base and rover receivers; the round-off scheme of widelane carrier phase, instant least-squares and Kalman filter-based LAMBDA with widelane carrier phase, instant least-squares and Kalman filter-based LAMBDA with dual frequency measurements. The paper presented the performance of each method using flight test data, which showed their strength and weakness in the aspects of time-to-first-fix, ambiguity resolution success ratio, and relative position errors. Based on that, we provided practical recommendations of RTK operations for moving vehicles.

• 한국군사과학기술학회지
• /
• 제8권4호
• /
• pp.24-31
• /
• 2005

This paper presents an implementation of a real-time multi-sensor data fusion algorithm for Flight Test Computer. The sensor data consist of positional information of the target from a radar, a GPS receiver and an INS. The data fusion algorithm is designed by the 21st order distributed Kalman Filter which is based on the PVA model with sensor bias states. A fault detection and correction logics are included in the algorithm for bad measurements and sensor faults. The statistical parameters for the states are obtained from Monte Carlo simulations and covariance analysis using test tracking data. The designed filter is verified by using real data both in post processing and real-time processing.

• Journal of Astronomy and Space Sciences
• /
• 제39권2호
• /
• pp.51-57
• /
• 2022

Cosmic radiation exposure of the flight crews in Korea has been managed by Radiation Safety Management around Living Life Act under Nuclear Safety and Security Commission. However, the domestic flight crews are excluded from the Act because of relatively low route dose exposure compared to that of international flight crews. But we found that the accumulated total annual dose of domestic flight crews is far from negligible because of relatively long total flight time and too many flights. In this study, to suggest the necessity of management of domestic flight crews' radiation exposure, we statistically analyzed domestic flight crew's accumulative annual dose by using cosmic radiation estimation models of the Civil Aviation Research Institute (CARI)-6M, Nowcast of Atmospheric Ionizing Radiation for Aviation Safety (NAIRAS), and Korean Radiation Exposure Assessment Model (KREAM) and compared with in-situ measurements of Liulin-6K LET spectrometer. As a result, the average exposure dose of domestic flight crews was found to be 0.5-0.8 mSv. We also expect that our result might provide the basis to include the domestic flight crews as radiation workers, not just international flight attendants.

• Journal of Welding and Joining
• /
• 제28권2호
• /
• pp.74-78
• /
• 2010

In this paper, a non-contact method of evaluating the thickness reduction in an aluminum sheet caused by corrosion and friction using SH-EMAT (shear horizontal, electromagnetic acoustic transducer) is described. Since this method is based on the measurement of the time-of-flight and amplitude change of guided waves caused from the thickness reduction, it provides information on the thinning defects. Information was obtained on the changes of the various wave features, such as their time-of-flight and amplitude, and their correlations with the thickness reduction were investigated. The interesting features in the dispersive behavior of selected guided modes were used for the detection of thinning defects. The measurements of these features using SH waves were performed on aluminum specimens with regions thinned by 7.2% to 29.5% of the total thickness. It is shown that the time-of-flight measurement provides an estimation of the thickness reduction and length of the thinning defects.

• 한국군사과학기술학회지
• /
• 제13권1호
• /
• pp.36-40
• /
• 2010

In this paper, the well-known LOB-based emitter localization using linear LSE algorithm is numerically implemented and the heuristic guidelines for the parameter values to achieve 1% RMS error are presented. In the simulation, we changed the total observation durations for LOB measurements, time interval between successive LOB measurements and sensor trajectories. The effects of the time interval of LOB measurements, the time duration of the LOB measurements and the angle of flight path arc on the performance are illustrated. The dependence of the performance on the various parameters is investigated and rule-of-thumbs for the parameter values corresponding to 1% RMS error are presented for each simulation condition.

• 한국항공운항학회지
• /
• 제18권2호
• /
• pp.1-8
• /
• 2010

In order to determine the possibility of using NDGPS signals for flight operations, in-flight measurements of signals transmitted from various ground reference stations(RS) were conducted along the air routes of South Korea. Signal strength and signal to noise ratio(SNR) data were collected along domestic flight routes and recorded with time. By using three-dimensional geographical position data of the aircraft, signal strength data of en-route position were calculated and used to obtain scatter-plot of signal strength. These results were used to outline the effective coverage and field strength hemispheres of the selected DGPS signals.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.880-883
• /
• 1996

Plasma Source Ion Implantation (PSII) technique was used for the hydrophilization or hydrophobization of polymer surfaces. Polymers were modified with different plasma gases such as oxygen, nitrogen, argon, and tetrafluoromethane, and for varying lengths of treatment time. Plasma ion treatment of oxygen, nitrogen, argon and their mixtures increased significantly the hydrophilic properties of polymer surfaces. More hydrophobic surfaces of polymers were formed after the treatment with tetrafluoromethane. A study of plasma source ion implanted polymers was performed using contact angle measurements and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS). The TOF-SIMS spectra and depth profile were used to obtain the information about the treated surfaces of polymers. The permanence of this technique could be evaluated with respect to ageing time. The surfaces treated with PSII gave better stability than other surface modification methods.

• 한국항공우주학회지
• /
• 제37권4호
• /
• pp.406-412
• /
• 2009

헬리콥터 시뮬레이터용 비행 시뮬레이션 모델은 비행 성능과 조종특성에 직접적인 영향을 주는 핵심 모델 중 하나로서, 헬리콥터 설계/제작사로부터 원천 자료 및 모델을 확보하여 개발하는 것이 일반적이다. 본 연구에서는 일반적인 개발 방식과는 다르게 헬리콥터 운용/정비 관련 가용한 자원을 활용하여 기본 모델을 구성하고 이를 비행시험 결과와 비교 튜닝하여 검증하는 방법을 채택하였다. 즉, 대상 헬리콥터인 KA-32T의 제작사로부터 헬리콥터 데이터를 확보할 수 없는 현실을 감안하여 정비교범, 비행교범, 해석, 실측, 논문 등을 기준으로 비행 시뮬레이션 기본 모델을 개발하였다. 이후 기준 데이터 획득을 위해 KA-32T를 대상으로 비행시험을 수행하였으며, 시뮬레이션 결과를 획득된 비행시험 결과와 비교 튜닝하여, 개발된 비행 시뮬레이션 모델이 FAA AC120-63 Level C 규격에 적합한 충실도를 보유함을 검증하였다.

• Smart Structures and Systems
• /
• 제20권3호
• /
• pp.385-396
• /
• 2017

The recent advancements in sensing technologies allow us to record measurements from target structures at multiple locations and with relatively high spatial resolution. Such measurements can be used to develop data-driven methodologies for condition assessment, control, and health monitoring of target structures. One of the state-of-the-art technologies, Fiber Optic Strain Sensors (FOSS), is developed at NASA Armstrong Flight Research Center, and is based on Fiber Bragg Grating (FBG) sensors. These strain sensors are accurate, lightweight, and can provide almost continuous strain-field measurements along the length of the fiber. The strain measurements can then be used for real-time shape-sensing and operational load-estimation of complex structural systems. While several works have demonstrated the successful implementation of FOSS on large-scale real-life aerospace structures (i.e., airplane wings), there is paucity of studies in the literature that have investigated the potential of extending the application of FOSS into civil structures (e.g., tall buildings, bridges, etc.). This work assesses the feasibility of using FOSS to predict operational loads (e.g., wind loads) on chain-like structures. A thorough investigation is performed using analytical, computational, and experimental models of a 4-story steel building test specimen, developed at the University of Southern California. This study provides guidelines on the implementation of the FOSS technology on building-like structures, addresses the associated technical challenges, and suggests potential modifications to a load-estimation algorithm, to achieve a robust methodology for predicting operational loads using strain-field measurements.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.343-344
• /
• 2007

Carrier mobility was measured using time-of-flight (TOF) measurements to investigate the transport properties of holes and electrons in stabilized a-Se film. A laser beam with pulse duration of 5 ns and wavelength of 350 nm was illuminated on the surface of a-Se with thickness of $400\;{\mu}m$. The measured transit times of hole and electron were about $8.73\;{\mu}s\;and\;229.17\;{\mu}s$, respectively. The experimental results showed that the hole and electron drifting mobility were $0.04584\;cm^2V^{-1}S^{-1}\;and\;0.00174\;cm^2V^{-1}s^{-1}\;at\;10\;V/{\mu}m$.