• Korean Journal of Materials Research
• /
• v.15 no.2
• /
• pp.79-84
• /
• 2005

The lowest activation temperature of a commercial vacuum getter reported so far in literature was about $400^{\circ}C$. Recently, $Ti_{0.3}Zr_{0.2}V_{0.5}$ alloy has been reported to exhibit the activation temperature lower than $200^{\circ}C$ when they are prepared as thin film. In this study, the alloy was prepared as bulk form and its activation temperature and hydrogen sorption properties were investigated in compliance with a standard method. The alloy powder was prepared by arc melting and subsequent HDH(Hydride-DeHydride) process. The activation temperature of the alloy was estimated from the ultimate pressure-temperature curve and located between $150^{\circ}C\;and\;200^{\circ}C$. The hydrogen sorption speed measured by an orifice method was 0.895 liter/sec which is comparable to thin film of same composition.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.5
• /
• pp.313-322
• /
• 2001

The effects of Zr/Ti concentration ratio in PLZT (10/y/z) thin films prepared by sol-gel method are investigated for the NVFRAM application. Rosette and pyrochlore phase are observed in PLZT (10/40/60) thin film and the (100) orientation, the grain size, and the surface roughness of PLZT thin films increase due to the increase of Ti amount in Zr/Ti concentration ratio. As Ti amount of Zr/Ti concentration ratio increases, the dielectric constants at 10KHz decrease from 600 to 400, while the loss tangents increase from 0.028 to 0.053 and the leakage current densities at 170 kY/cm decrease from 1.64$\times$10$^{-6}$ to 1.26$\times$10$^{-7}$ A/$\textrm{cm}^2$. In the results of hysteresis loops measured at $\pm$ 170 ㎸/cm, the remanent polarization and the coercive field increase from 6.62 to 12.86 $\mu$C/$\textrm{cm}^2$ and from 32.15 to 56.45 ㎸/cm, respectively, according to the change from 40/60 to 0/100 in Zr/Ti concentration ratio. Fatigue and retention properties also improve much as the Zr/Ti concentration ratio change from 40/60 to 0/100. After applying 10$^{9}$ square pulses with $\pm$5V, the remanent polarization of the PLZT (10/40/60) thin film decreases 50％ from the initial state while that of the PLZT (10/0/100) thin film decreases 30％. In the results of retention measurements of 10$^{5}$ s, the remanent polarization of the PLZT (10/0/100) thin film decreases only 11％ from the initial state, while that of the PLZT (10/40/60) thin film decreases 40%.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.5
• /
• pp.367-372
• /
• 2013

Hydrogen storage as a metal hydride is the most promising alternative because of its relatively large hydrogen storage capacities near room temperature. TiMn2-based C14 Laves phases alloys are one of the promising hydrogen storage materials with easy activation, good hydriding-dehydriding kinetics, high hydrogen storage capacity and relatively low cost. In this work, multi-component, hyper-stoichiometric $Ti_{0.85}Zr_{0.13}(Fe_x-V)_{0.56}Mn_{1.47}Ni_{0.05}$ C14 Laves phase alloys were prepared by a vacuum induction melting for a hydrogen storage tank. Since pure vanadium (V) is quite expensive, the substitution of the V element in these alloys has been tried and some interesting results were achieved by replacing V by commercial ferrovanadium (FeV) raw material. In addition, the melt-spinning process, which was applied to the manufacturing of some of these alloys, could make the plateau slopes much flatter, which resulted in the increase of reversible hydrogen storage capacity. The improvement of sloping properties of melt-spun $Ti_{0.85}Zr_{0.13}(Fe_x-V)_{0.56}Mn_{1.47}Ni_{0.05}$ alloys was mainly attributed to the homogeneity of chemical composition.

• Korean Journal of Materials Research
• /
• v.2 no.1
• /
• pp.43-51
• /
• 1992

Thin films of )$Pb(Zr, \;TiO_3$ are fabricated by MOCVD using ultrasonic spraying. The films having perovskite structure are made at low deposition temperature, $300-450^{\circ}C$. The phase and composition of the films vary with the composition of the starting solution and the deposition temperature. Dielectric constant of the films is 187 at 1MHz. Ferroelectric hysterysis loop measurements indicate a remanant polarization of $5.5{\mu}C/cm^2$, and coercive field of 65kV/cm. Resistivity of thin films is about $10^{11}{\Omega}cm$ and the breakdown electric field abort 35kV/cm.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.7
• /
• pp.77-84
• /
• 1995

We studied the effects of the Zr/Ti ration and the bottom electrode (Pt or ITO) on the electrical properties of PZT thin films prepared by sol-gel method. Their permittivities and tagent losses with the variation of frequencies were measured by the LCR meter and their maximum polarizations, remanent polarizations, and coercive fields were obtained from the hysteresis loops measured by the Sawyer-Tower circuit. For the PZT thin film of the Zr/Ti ration of 53/47, permittivity at 10kHz, coercive field, maximum and remanent polarizations ere measured as 952, 20.7kV/cm, 10.43${\mu}C/cm^{2}$ and 4.3${\mu}C/cm^{2}$, respectively. For the film of the Zr/Ti ration of 25/75, coercive field, maximum and remanent polarizations were measured as 33.12kV/cm, 5.59${\mu}C/cm^{2}$ and 1.5${\mu}C/cm^{2}$, respectively. For the film of the Zr/Ti ratio of 75/25, they were measured as 23.8kV/cm, 7.45${\mu}C/cm^{2}$, and 3.5${\mu}C/cm^{2}$, repectively. Our investigation into the effects of the lower electrode on the electrical properties of PZT films showed the following results. The permittivities of the PZT films deposited on the ITO electrode decreased more quickly than those of the PZT films on the Pt electrode. The tangent losses of the former films increased more quickly than those of the latter. These may be due to the degradation of the quality of the interface between the electrode and the film, which results from the diffusion of Pb. It is also noticeable that permittivities and tangent losses of the PZT films deposited on the ITO electrode varied differently with the Zr/Ti ratio. This may indicate that the quality of the interface between the electrode and the film changes with the Zr/Ti ration of the PZT film.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1240_1241
• /
• 2009

In this paper, sol-gel-spin coated $Pb(ZrTi)O_3$ thin film with $ZrO_2$ buffer-layer and $PbTiO_3$ seed-layer was investigated for vibration MEMS energy harvester to scavenge power from ambient vibration via d33 piezoelectric mode. Piezoelectric thin film deposition techniques on insulating layer is the important key for $d_{33}$ mode of piezoelectric vibration energy harvester. $ZrO_2$ buff-layer was utilized as an insulating layer. $PbTIO_3$ seed-layer was applied as an inter-layer between PZT and $ZrO_2$ layer to improve the crystalline of PZT thin film. The fabricated PZT thin film had a remanent polarization of 5.3uC/$cm^2$ and the coercive field of 60kV/cm. The fabricated energy harvester using PZT thin film with PTO seed-layer generated 1.1uW of electrical power to $2.2M{\Omega}$ of load with $4.4V_{pvp}$ from vibration of 0.39g at 528Hz.

• Corrosion Science and Technology
• /
• v.9 no.1
• /
• pp.12-15
• /
• 2010

Ti-13Nb-13Zr (TNZ) alloy has attracted considerable research attention in the last decade as a suitable substitute for the commercially used Ti-6Al-4V (TAV) alloy for orthopedic and dental implant applications. Hence, in the present work, a comparative evaluation has been performed on the electrochemical corrosion behavior of TNZ and TAV alloys in 0.9 wt.% NaCl solution. The result of the study showed that both the alloys had similar electrochemical behavior. The corrosion resistance of TAV alloy is found to be marginally superior to that of TNZ alloy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.436-441
• /
• 1998

$Pt/SrTiO_3/Pb_x(Zr_{0.52}, Ti_{0.48})O_3/SrTiO_3/Si$ structure was prepared by rf-magnetron sputtering method for use in nondestructive read out ferroelectric RAM(NDRO-FEAM). PBx(Zr_{0.52}Ti_{0.48})O_3}$(PZT) and $SrTiO_3$(STO) films were deposited respectively at the temperatures of $300^{\circ}C and 500^{\circ}C$on p-Si(100) substrate. The role of the STO film as a buffer layer between the PZT film and the Si substrate was studied using X-ray diffraction (XRD), Auger electron spectroscopy (ASE), and scanning electron microscope(SEM). Structural analysis on the interfaces was carried out using a cross sectional transmission electron microscope(TEM). For PZT/Si structure, mostly Pb deficient pyrochlore phase was formed due to the serious diffusion of Pb into the Si substrate. On the other hand, for STO/PZT/STO/Si structure, the PZT film had perovskite phase and larger grain size with a little Pb interdiffusion. the interfaces of the PZT and the STO film, of the STO film and the interface layer and $SiO_2$, and of the $SiO_2$ and the Si substate had a good flatness. Across sectional TEM image showed the existence of an amorphous layer and $SiO_2$ with 7nm thickness between the STO film and the Si substrate. The electrical properties of MIFIS structure was characterized by C-V and I-V measurements. By 1MHz C-V characteristics Pt/STO(25nm)/PZT(160nm)/STO(25nm)/Si structure, memory window was about 1.2 V for and applied voltage of 5 V. Memory window increased by increasing the applied voltage and maximum voltage of memory window was 2 V for V applied. Memory window decreased by decreasing PZT film thickness to 110nm. Typical leakage current was abour $10{-8}$ A/cm for an applied voltage of 5 V.

• Journal of the Korean Magnetics Society
• /
• v.15 no.4
• /
• pp.231-235
• /
• 2005

We studied the microstructural evolution of ZrTM-Al (TM=Nb and Ti) alloy films, MR and electrical properties of the MTJ with $ZrTM-AlO_x$ barrier as a function of Zr/TM ratio. We observed that the ternary-oxide barrier reduced the TMR ratio due mainly to the structural defects such as the surface roughness. The change in TMR ratio and $V_h$ with Zr/TM ratio exactly corresponds to the systematic changes in the microstructural variation. Although the MTJ with ternary oxide reduced the TMR and the electrical stabilities, the junction resistances decreased as the Ti and Nb concentration increased due to the band-gap reduction caused by the formation of extra bands

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.5
• /
• pp.1-1
• /
• 2001

비휘발성 메모리 소자로의 응용의 관점에서, sol-gel 방법으로 La 을 10mo1% 로 고정시킨 PLZT (10/y/z) 박막을 제작하여 Zr/Ti 조성비에 따른 구조적 및 전기적 특성을 조사하였다. PLZT(10/40/60) 박막은 로제트와 파이로클로르 상이 관찰되었으며, Zr/Ti 조성비에서 Ti 함유량이 증가함에 따라, (100) 배향성, 결정립 크기와 표면 거칠기는 증가되었다. 또한 Zr/Ti 조성비에서 Ti 함유량이 증가함에 따라, 10㎑ 에서 비유전율은 600 에서 400 으로 감소된 반면, 유전손실은 0.028 에서 0.053 로 증가되었으며, 170 ㎸/cm 에서 누설전류밀도는 1.64×$10^{-6}$ 에서 1.26×$10^{-7}$A/㎠ 으로 감소되었다. 그리고 ± 170㎸/㎝ 에서 측정한 PLZT 박막의 이력곡선을 측정한 결과, Zr/Ti 조성비가 40/60 에서 0/100 로 변화함에 따라 PLZT 박막의 잔류분극과 항전계는 6.62 에서 12.86 μC/cm2, 32.15 에서 56.45㎸/㎝ 로 각각 증가되었으며, 피로와 retention 특성 역시 개선되었다. PLZT 박막에 ±5V 의 사각펄스를 $10^9$ 회 인가하여 피로특성을 측정한 결과, PLZT(10/40/60) 박막의 잔류분극은 초기분극값으로부터 50% 감소된 반면, PLZT(10/0/100) 박막은 30% 감소되었다. 또, $10^5$ 초의 retention 결과에서 PLZT(10/0/100) 박막은 초기분극값에서 오직 11% 만이 감소된 반면, PLZT(10/40/60) 박막은 40% 감소되었다.