• Proceedings of the Korean Vacuum Society Conference
• /
• 2004.02a
• /
• pp.108-108
• /
• 2004

• Particle and aerosol research
• /
• v.12 no.2
• /
• pp.37-42
• /
• 2016

$CeO_2$ nanoparticles were prepared by a flame spray pyrolysis from aqueous solution of cerium nitrate. The morphology, structure crystallinity and specific surface area of as-prepared nanoparticles were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), and Brunauer-Emmett-Telle (BET). The $CeO_2$ nanoparticles about 5 nm in diameter showed a cubic fluorite structure and polyhedral morphology. The average particle size increased as the cerium nitrate concentration increased. UV absorption performance of the as-prepared nanoparticles was measured by UV-visible spectroscopy. UV absorption of $CeO_2$ nanoparticles was more effective than that of commercial $TiO_2$ nanoparticles. Effect of dopants such as Ti and Zn to $CeO_2$ nanoparticles on UV absorption properties was also investigated. In case of $Ti/CeO_2$, and $Zn/CeO_2$ nanoparticles, they showed a little higher UV absorption values compared with $CeO_2$ nanoparticles. The as-prepared nanoparticles can be promising materials with high UV absorption value.

• Resources Recycling
• /
• v.28 no.5
• /
• pp.68-73
• /
• 2019

Ilmenite is one of the principal ores for the production of titanium dioxide. To produce titanium dioxide with purity higher than 99.9% from ilmenite, Ti(IV) should be separated from the dissolved impurities such as Fe(III), Si(IV), and Mn(II) present in ilmenite. In this work, a hydrometallurgical process was investigated to recover pure titanium dioxide from ilmenite by HCl leaching followed by separation and hydrolysis of Ti(IV). An optimum leaching condition was obtained by investigating the effect of HCl concentration, pulp density, and leaching time on the leaching percentage of Ti(IV), Fe(III), Si(IV), and Mn(II). Ammonium hydroxide and sodium hydroxide solutions were employed as neutralizing agents to hydrolyze Ti(IV) from the stripping solution of Ti(IV). Titanium dioxide of the anatase phase was obtained by calcination of the hydrolyzed precipitates with $NH_4OH$ solution. A hydrometallurgical process can be developed to produce pure $TiO_2$ powders from ilmenite.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.37-43
• /
• 1999

Co-firing incompatibility between the low temperature sinterable Glass/ceramic and Ag-thick film was studied. The dielectric material, which has been developed for microwave frequency applications, consists of $SiO_2-TiO_2-Bi_2O_3$-$Bi_2O_3$-RO system(RO:BaO -CaO-SrO) crystallizable glass and $Al_2O_3$as a ceramic filler. The large camber in the sintered specimen and cracks at the Ag-film under the influence of the camber occurred due to the difference of densification rate between the ceramic sheet and the Ag-film $B_2O_3$addition to the Glass/ceramic mixture reduced the severe camber. The cambers decreased with increasing the $B_2O_3$ content, and completely disappeared with 14 vol% $B_2O_3$addition. With additions of $B_2O_3$, $\varepsilon_{r}$ decreased abruptly, Q$\times$f value increased largely and the $\tau_f$ value of the material quickly shifted to positive one.

• Journal of the Mineralogical Society of Korea
• /
• v.16 no.3
• /
• pp.215-222
• /
• 2003

The Rietveld structure refinement for the natural trioctahedral mica, phlogopite-1M (Parker Mine, Quebec, Canada) has been done by high resolution neutron powder diffraction at $25^{\circ}C$ and -263$^{\circ}C$. The structural formula of phlogopite determined by electron probe microanalysis is $K_2$(M $g_{4.46}$F $e_{0.83}$A $l_{0.34}$ $Ti_{0.22}$)(S $i_{5.51}$A $l_{2.49}$) $O_{20}$(O $H_{3.59}$ $F_{0.41}$). Cell parameters are a=5.30∼5.31 $\AA$, b=9.18∼9.20 $\AA$, c=10.18∼10.21 $\AA$, $\beta$=100.06∼100.08$^{\circ}$. Refinements converged to R values in the range of $R_{p}$=2.35%, $R_{wp}$=3.01%, respectively. In this study, the OH bond length is calculated to 0.93 $\AA$ at room temperature and 1.03 $\AA$ at -263$^{\circ}C$, and the angles between OH vector and (001) plane are obtained 93.4$^{\circ}$∼93.6$^{\circ}$. The decrease in the length of OH with the increase in temperature should be due to the hydrogen bonding in the structure of phogopite.e.e.f phogopite.e.e.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.533-534
• /
• 2006

1mm-thick BLT ceramics were sintered in accordance with a bulk ceramic fabrication process. All XRD peaks detected in the sintered ceramics were indexed as the Bi-layered perovskite structure without secondary phases. Density was increased with increasing the sintering temperature up to $1050\;^{\circ}C$ and the maximum value was about 98% of the theoretical density. The remanent polarization (2Pr) value of BLT ceramic sintered at $1050\;^{\circ}C$ was approximately $6.5\;{\mu}C/cm^2$ at the applied voltage of 4.5kV. From these results, a BLT ceramic target for plused laser deposition (PLD) system was successfully fabricated.

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.516-520
• /
• 2005

Conditions for formation of perovskite Pb(Zr$_{0.52}$Ti$_{0.48}$)O$_{3}$ phase by the hydrothermal synthesis are investigated. Pb(Zr$_{0.52}$ Ti$_{0.48}$)O$_{3}$ ceramics were synthesized by hydrothermal process above 180$^{\circ}C$ for 2 h reaction using 5$\~$30 M KOH solution as a mineralizer. Particle size increases in proportion to the mineralizer concentration. As a result of EOX analysis, PZT powders synthesized using 50 M of KOH as a mineralizer were considered as 2.42 mol$\%$ K doped-PZT powders. And 2.42 mol$\%$ K doped-PZT has much higher mechanical quality factor than undoped PZT ceramics. The sintering properties showed 7.987 g/cm$^{3}$ of sintered density and 3$\~$4 $\mu$m of grain size.

• Journal of the Korean Ceramic Society
• /
• v.23 no.3
• /
• pp.15-20
• /
• 1986

Formation of powders and electromechanical coupling factor of $Pb(Mn_{1/3} Sb_{2/3})_{0.08} Ti_{0.495}Zr_{0.425}O_3$ by hydro-thermal synthesis are described. The hydrothermal reactions each were accomplished at 12$0^{\circ}C$~25$0^{\circ}C$ for 5hours and sintering was accomplished at 1, .20$0^{\circ}C$ for 1hours. The PZT powders by hydrothermal synthesis were formed above 16$0^{\circ}C$ and the forms were cubic types. The ratio of grain size of sintered sample to powder was slowly decreased with the rising of hydrothermal reactino temperature but decreased rapidly above 22$0^{\circ}C$ Sintering density was decreased with the rising of hydrothermal reaction temperature above 16$0^{\circ}C$ but dielectric constant was increased. Electromechanical coupling factor $K_P$ was almost constant at 16$0^{\circ}C$~24$0^{\circ}C$ range and the value of $K_P$ was about 0.43-0.45.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.3
• /
• pp.241-247
• /
• 1999

In this study, the relation of the preservation efficacy reduction with methyl paraben of parahydroxybenzoic acid derivatives was investigated using the dialysis membrane method with tween-80 of surfactant and $TiO_2/Talc$ of inorganic powder meterial from emulsion system. It was found that the preservation efficacy of tween-80 and $TiO_2/Talc$ from emulsion system was reduced due to the adsorption of methyl paraben. According to the microbe test, In case of tween-80, MBC appeared in 0.19 w/v% and in case of $TiO_2/Talc$, MBC appeared in 0.22w/v% / 0.23w/v%. In general, the equation of Talc's adsorption weight($A{\cdot}W$) has a tendency to show in $A{\cdot}W=11.5C^{0.745}$

• Journal of the Korean Chemical Society
• /
• v.42 no.6
• /
• pp.652-656
• /
• 1998

$(Ba_{0.8-x}Sr_{0.2})Y_xTiO_3\;(BSYT)$ powders were prepared by the calcination of metal-oxalate precipitates, which were obtained by wet chemical method using Ba, Sr, Y and Ti-nitrates and oxalic acid. Yttrium content, sintering temperature and cooling rate were taken as experimental factors. Response surface method was applied to modelling of the room temperature resistivity of BSYT. The results indicated that the Yttrium content had larger effect on the room temperature resistivity and minimum room temperature resistivity was at Yttrium content of 0.24 mol%. The validity of a modelling equation was confirmed by comparing the measured room temperature resistivity with the calculated one.