• Korean Journal of Materials Research
• /
• v.10 no.4
• /
• pp.282-289
• /
• 2000

$PbTiO_3$ films were fabricated by electron cyclotron resonance plasma enhanced chemical vapor deposition(ECR-PECVD). Deposition characteristics of $PbTiO_3$films on $RuO_2$ and Pt substrates were investigated with varying the flow rate of metalorganic source and substrate temperature. The residence time of Pb-oxide molecules in much longer on $RuO_2$ than on Pt substrate, while the perovskite nucleation is more difficult on $RuO_2$ than on Pt substrate. Therefore, the process conditions to obtain the single perovskite $PbTiO_3$ phase are more restricted on $RuO_2$ than on Pt substrates. An introduction of Ti-oxide seed layer increases perovskite nucleation density and thus enlarges the process window to obtain the single perovkite phase. The introduction of Ti-oxide seed layer make the PZT film that Ti-components of $PbTiO_3$ are partially substituted with Zr atoms have single perovskite phase for the wide range of Zr/(Zr+Ti) concentration ratios.

• Clean Technology
• /
• v.21 no.1
• /
• pp.39-44
• /
• 2015

This study investigated the effects of six metal oxide nanoparticles (NPs: CuO, NiO, TiO₂, Fe₂O₃, Co₃O₄, ZnO) on seed germination and germination index (G.I) for five types of seeds: Brassica napus L., Malva verticillata L., Brassica olercea L., Brassica campestris L., Daucus carota L. NPs of CuO, ZnO, NiO show significant toxicity impacts on seed activities [CuO (6-27 mg/L), ZnO (16-86 mg/L), NiO (48-112 mg/L)], while no significant effects were observed at > 1000 mg/L of TiO₂, Fe₂O₃, Co₃O₄. Tested five types of seed showed different sensitivities on seed germination and root activity, especially on NPs of CuO, ZnO, NiO. Malva verticillata L. seed was highly sensitive to toxic metal oxide NPs and showed following EC₅₀s : CuO 5.5 mg/L, ZnO 16.4 mg/L, NiO 53.4 mg/L. Mostly following order of toxicity was observed, CuO > ZnO > NiO > Fe₂O₃ ≈ Co₃O₄ ≈ TiO₂, where slightly different toxicity order was observed for carrot, showing CuO > NiO ≈ ZnO > Fe₂O₃ ≈ Co₃O₄ ≈ TiO₂.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.983-989
• /
• 2005

[ $PZT(Pb(Zr,Ti)O_3)$ ] thin films were deposited by multi-target reactive sputtering method on $RuO_2$ substrates. Pure perovskite phase PZT films could be obtained by introducing Ti-oxide seed layer on the $RuO_2$ substrates prior to PZT film deposition. The PZT films deposited on the $RuO_2$ substrates showed highly voltage-shifted hysteresis loop compared with the films deposited on the Pt substrates. The surface of $RuO_2$ substrate was found to be reduced to metallic Ru in vacuum at elevated temperature, which caused the formation of oxygen vacancies at the initial stage of PZT film deposition and gave rise to the voltage shift in the P-E hysteresis loop of the PZT capacitor. The fatigue characteristics of the PZT capacitors under unipolar wane electric field were different from those under bipolar wane. The fatigue test under unipolar wane showed the increase of polarization. It was thought that the ferroelectric domains which had been pinned by charged defects such as oxygen vacancies and the charged defects were reduced in number by combining with the electrons injected from the electrode under unipolar wave, resulting in the relaxation of the ferroelectric domains and the increase of polarization.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.6
• /
• pp.396-401
• /
• 2014

Nanomaterials have been widely used in many fields. This study investigates the effects of metal oxide nanoparticles (CuO, NiO, $TiO_2$, $Fe_2O_3$, $Co_3O_4$, ZnO) on germination and germination index (G.I.) of seeds, Lactuca and Raphanus. Under aqueous exposure, CuO on Lactuca shows the most significant impacts on activities compared to others, showing $EC_{50s}$ for germination and G.I. as 0.46 mg/L and 0.37%, respectively. The effects of nanoparticle phytotoxicity on seed Lactuca was much higher than that of Raphanus. In general, the toxicities on seed germination and germination index were as following orders : CuO > ZnO > NiO ${\gg}$ $TiO_2$, $Fe_2O_3$, $Co_3O_4$. No measurable inhibition was observed at 1,000 mg/L (maximum exposure concentration) of $TiO_2$, $Fe_2O_3$, $Co_3O_4$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.326-326
• /
• 2011

반도체 소자의 집적화/소형화에 따라, 낮은 비저항을 가진 구리(Cu)를 이용한 배선공정에 관한 연구가 활발하게 진행되고 있다. 구리배선 공정에 있어 전기 도금법이 다양하게 적용됨에 따라, 구리도금 박막 형성을 위해 사용되는 Cu seed 층의 상태는 배선으로 형성된 Cu박막 특성에 크게 영향을 미친다 [1-3]. 본 연구에서는 sputter 방식으로 증착된 Cu seed 층(Cu seed / Ti / Si) 위에 형성된 자연산화막을 제거하기 위하여 다양한 세정방법을 도입하여 비교 분석하였다. 계면활성제인 TS-40A를 비롯한 NH4OH 용액과 H2SO4 용액을 사용하여 Cu seed 층 위에 형성된 구리산화막을 제거함으로서 형성된 표면형상 및 표면상태를 조사분석 하였다. FE-SEM (Field Emission Scanning Electron Microscope)을 이용하여 표면 처리된 Cu seed층 표면의 형상 및 roughness 등을 측정하였고, XPS (X-ray Photoelectron Spectroscopy)를 이용하여 표면 처리된 Cu seed 표면의 화학구조 및 불순물 상태를 조사하였다.

• Journal of Powder Materials
• /
• v.13 no.6 s.59
• /
• pp.396-400
• /
• 2006

The Ti-Ni alloy nanopowders were synthesized by a levitational gas condensation (LGC) by using a micron powder feeding system and their particulate properties were investigated by x-ray diffraction (XRD), transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET) method. The starting Ti and Ni micron powders $150{\mu}m$ were incorporated into the micron powder feeding system. An ingot type of the Ti-Ni ahoy was used as a seed material for the levitation and evaporation reactions. The collected powders were finally passivated by oxidation. The x-ray diffraction experiments have shown that the synthesized powders were completely alloyed with Ti and Ni and comprised of two different cubic and monoclinic crystalline phases. The TEM results showed that the produced powders were very fine and uniform with a spherical particle size of 18 to 32nm. The typical thickness of a passivated oxide layer on the particle surface was about 2 to 3 nm. The specific surface area of the Ti-Ni alloy nanopowders was $60m^2/g$ based on BET method.

• Clean Technology
• /
• v.20 no.3
• /
• pp.306-313
• /
• 2014

Nanoporous $TiO_2$ films are commonly used as working electrodes in dye-sensitized solar cells (DSSCs). So far, there have been attempts to synthesize films with various $TiO_2$ nanostructures to increase the power-conversion efficiency. In this work, vertically aligned rutile $TiO_2$ nanorods were grown on fluorinated tin oxide (FTO) glass by hydrothermal synthesis, followed by deposition of an anatase $TiO_2$ film. This new method of anatase $TiO_2$ growth avoided the use of a seed layer that is usually required in hydrothermal synthesis of $TiO_2$ electrodes. The dense anatase $TiO_2$ layer was designed to behave as the electron-generating layer, while the less dense rutile nanorods acted as electron-transfer pathwaysto the FTO glass. In order to facilitate the electron transfer, the rutile phase nanorods were treated with a $TiCl_4$ solution so that the nanorods were coated with the anatase $TiO_2$ film after heat treatment. Compared to the electrode consisting of only rutile $TiO_2$, the power-conversion efficiency of the rutile-anatase hybrid $TiO_2$ electrode was found to be much higher. The total thickness of the rutile-anatase hybrid $TiO_2$ structures were around $4.5-5.0{\mu}m$, and the highest power efficiency of the cell assembled with the structured $TiO_2$ electrode was around 3.94%.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.13-16
• /
• 2013

A lot of various researches have been going on to use heat spreader for LED module. Nano porous aluminum anodic oxide (AAO) applied LED, which is produced from anodization, is easy and economically advantageous. Convensional LED module is consist of aluminum/adhesive/copper circuit. The polymer adhesive in this module is used as heat spreader. However the thermal emission of LED component is degraded because of low heat conductivity of polymer and also reliability of LED component is reduced. Therefore, AAO in this work was applied to heat spreader of LED module which has higher heat conductivity compare to polymer. Bonding strength between AAO and copper circuit was improved with Ti/Cu seed layer by copper sputtering process (DBC) before the bonding. And this copper circuit has been fabricated by electro plating method. Peel strength of AAO and copper circuit in this work showed range between 1.18~1.45 kgf/cm with anodizing process which is very suitable for high power LED application.

• Korean Journal of Materials Research
• /
• v.11 no.9
• /
• pp.769-775
• /
• 2001

High quality PZT piezoelectric thin films were sputter- deposited on$ RuO_2$/$SiO_2$/Si substrates by using 2-step deposition method. As the first step, PZT seed layers were fabricated at a low temperature($475^{\circ}C$ ) to form a pure perovskite phase by reducing the volatility of Pb oxide. and then, as the second step, the PZT films were deposited at high temperatures ($530^{\circ}C$~$570^{\circ}C$) to reduce the defect density in the films. By this method, the pure perovskite phase was obtained at high deposition temperature range ($530^{\circ}C$~$570^{\circ}C$) and the superior electrical properties of PZT films were obtained on $RuO_2$substrate : 2Pr : 60$\mu$C/$\textrm{cm}^2$, $E_c: 60kV/cm, \;J_t: 10^{-6}A/cm^2\; at\; 250kV/cm$. The residual stress of PZT films fabricated by the 2-step deposition method was tensile and below 150MPa. It was attempted to control the residual stress in the PZT films by applying a negative bias to the substrate. As the amplitude of the substrate bias was increased, the residual tensile stress was slightly decreased, however, the ferroelectric properties of PZT films were degraded by ion bombardment.