• 한국재료학회지
• /
• 제7권2호
• /
• pp.162-170
• /
• 1997

This study has evaluated the dissimialr weldability of Incoloy 825 Ni base alloy with a mild steel(SS41). Further a compatibility study of wrveral Ni base filler metals with the dissimilar joint between the two alloys was also included. The dissimilar weldability of Incoloy 825 with mild steel is strongly dependent upon the type of the filler metal used. Among the filler metals, ENiCrFe which has a chemical comosition similar to that of Incoloy 825 was found to be most compatible to the joint. In addition, a filler metal which showed a good cracing resistance in one dissimiar alloy combination was not necessarily graranteed to other combination. Microstructural examination with SEM, TEM and Auger revealed that the solidification cracking resestance of the dissimilar joint. between Incoloy 835 and SS41 was closely with the Ti+Nb content and with the content of a low melting eutectic phase of Laves relatibve to that of MC type phase.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.118-121
• /
• 2005

The square cup drawing of magnesium alloy AZ31 $(aluminum\;3\%,\;Zinc\;1\%)$ sheets was studied by experimental approach in various temperatures (200, 250, 300, 350, $400^{\circ}C$) when blank holding force (BHF) was controlled in real-time. And so on, the drawability was measured with the different die and punch coating. The square cup drawing test was performed by three different coated punches (CrN, TiCN, Non-coated). BHF was set about 2.0 KN, forming speed was 50 mm/min, blank thickness were 0.5, 1.0mm and the cup size was 40 mm by 60 mm after forming. The experimental data of square cup drawing test show that the tools coating and temperature were effect on the drawbility.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(2)
• /
• pp.80-85
• /
• 1997

Studies on particles formed in the laser melted zone (LMZ) of sensitized Ni base Alloy 600 have been carried out using microscopic equipments. Most of them were identified as TiN type and MgS type particles were also found in the cell boundaries. All of the particles were located in the cellular solidification region, but no particle was formed in the plane front solidification regions of the LMZ. Cr carbides which had formed during sensitization treatment were completely melted during laser surface melting and hardly re-precipitated during the matrix solidification.

• The Journal of Advanced Prosthodontics
• /
• 제10권5호
• /
• pp.340-346
• /
• 2018

PURPOSE. In this study, the shear bond strengths (SBS) of luting cements to fixed superstructure metal surfaces under various seating forces were investigated. MATERIALS AND METHODS. Seven different cements [Polycarboxylate (PCC), Glass-Ionomer (GIC), Zinc phospahate (ZPC), Self-adhesive resin (RXU), Resin (C&B), and Temporary cements ((RXT) and (TCS))] were bonded to a total number of 224 square blocks ($5{\times}5{\times}3mm$) made of one pure metal [Titanium (CP Ti) and two metal alloys [Gold-Platinum (Au-Pt) and Cobalt-Chrome (Co-Cr)] under 10 N and 50 N seating forces. SBS values were determined and data were analyzed with 3-way ANOVA. Pairwise comparisons and interactions among groups were analyzed with Tukey's simultaneous confidence intervals. RESULTS. Overall mean scores indicated that Co-Cr showed the highest SBS values ($1.96{\pm}0.4$) (P<.00), while Au-Pt showed the lowest among all metals tested ($1.57{\pm}0.4$) (P<.00). Except for PCC/CP Ti, RXU/CP Ti, and GIC/Au-Pt factor level combinations (P<.00), the cements tested under 10 N seating force showed no significantly higher SBS values when compared to the values of those tested under 50 N seating force (P>.05). The PCC cement showed the highest mean SBS score ($3.59{\pm}0.07$) among all cements tested (P<.00), while the resin-based temporary luting cement RXT showed the lowest ($0.39{\pm}0.07$) (P<.00). CONCLUSION. Polycarboxylate cement provides reliable bonding performance to metal surfaces. Resin-based temporary luting cements can be used when retrievability is needed. GIC is not suitable for permanent cementation of fixed dental prostheses consisting of CP Ti or Au-Pt substructures.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2008년도 추계학술대회 초록집
• /
• pp.11-12
• /
• 2008

Micron-sized Co-alloy T800 powder was coated on Inconel718 (IN718) using high velocity oxygen fuel (HVOF) thermal spraying by the optimal coating process (OCP) determined from the best surface hardness of 16 coatings prepared by Taguchi program. The surface hardness improved 140-160 % from 399 Hv of IN718 to 560-630 Hv by the coating. Porosity of the coating was 1.0-2.7 %, strongly depending on spray parameters. Both friction coefficients (FC) and wear traces (WT) of the coating were smaller than those of IN718 substrate at both $25^{\circ}C$ and $538^{\circ}C$. FC and WT of IN718 and coating decreased with increasing the surface temperature. Tensile bond strength (TBS) and fracture location (FL) of Ti64/T800 were 8,770 psi and near middle of T800 coating respectively. TBS and FL of Ti64/NiCr/T800 were 8,740 psi and near middle of T800 coating respectively. This showed that cohesion of T800 coating was 8,740-8,770 psi, and adhesion of T800 on Ti64 and NiCr was stronger than the cohesion of T800.

• 한국재료학회지
• /
• 제25권11호
• /
• pp.636-641
• /
• 2015

Titanium has many special characteristics such as specific high strength, low elastic modulus, excellent corrosion and oxidation resistance, etc. Beta titanium alloys, because of their good formability and strength, are used for jet engines, and as turbine blades in the automobile and aerospace industries. Low cost beta titanium alloys were developed to take economic advantage of the use of low-cost beta stabilizers such as Mo, Fe, and Cr. Generally, adding a trace of boron leads to grain refinement in casted titanium alloys due to the pinning effect of the TiB phases. This study analyzed and evaluated the microstructural and mechanical properties after plastic deformation and heat treatment in boron-modified Ti-2Al-9.2Mo-2Fe alloy. The results indicate that a trace of boron addition made grains finer; this refinement effect was found to be maintained after subsequent processes such as hot forging and solution treatment. This can effectively reduce the number of required manufacturing process steps and lead to savings in the overall cost as well as low-cost beta elements.

• 한국재료학회지
• /
• 제3권1호
• /
• pp.58-64
• /
• 1993

고탄소 Dr-Ti 합금강의 회전접촉 피로마모실험에서 실험조건에 따라 다르게 변화하는 subsurface zone의 가공경와의 정도를 잔류응력의 분포로서 조사하였다. 시험전 표면잔류응력은 마모특성에 영향을 주지 못하였고, 접촉응력과 회전속도가 증가할수록 표면 잔류응력은 감소하여 갔으나 subsurface zone내의 최대압축잔류응력은 증가하였고, 그의 포화깊이는 깊었다. 이들 실험결과와 이론적 전단응력의 분포와의 관계에 관하여 검토하였다.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2015년도 임시총회 및 하계학술연구발표회
• /
• pp.120-120
• /
• 2015

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권7호
• /
• pp.890-899
• /
• 2014

오스테나이트계 스테인리스강은 우수한 내식성으로 인해 다양한 산업에 널리 적용되는 재료이다. 그러나 열처리나 용접 실시 후 입계에 크롬 탄화물 생성으로 크롬 결핍대가 형성되어, 입계의 내식성이 상대적으로 취약해지는 문제점이 있다. 이를 해결하기 위해 Ti 또는 Nb과 같은 탄소 안정화 원소를 첨가하여 크롬 탄화물 생성을 억제한다. 이러한 안정화된 스테인리스강에 대한 해수환경하에서의 내식성에 관한 연구는 적은 실정이다. 본 연구에서는 안정화 원소(Ti 및 Nb)를 함량 변수로 첨가한 스테인리스강에 대해 해수환경하에서 전기화학적 특성을 평가하고자 하였다. 이를 위해 합금원소 첨가에 따른 미세조직의 변화를 관찰하였으며, 자연전위 측정과 동전위분극 실험을 통해 전기화학적 특성을 파악하였다. 미세조직 관찰 결과, 모든 시편에서 오스테나이트 기지상 이외에 합금원소 첨가에 따른 개재물이 관찰되었다. 이러한 개재물은 기지 조직과 상이한 전기화학적 특성을 가지는 것으로 판단되며, 안정화 원소의 종류 및 함량에 따라 뚜렷한 전기화학적 특성 차이를 나타냈다. 본 연구 결과 오스테나이트계 스테인리스강에 내식성 향상을 위해 첨가되는 Ti 또는 Nb은 첨가량에 따라 서로 다른 전기화학적 특성을 나타내므로, 이를 고려한 합금 설계가 중요할 것으로 사료된다.

• 한국재료학회지
• /
• 제16권9호
• /
• pp.557-563
• /
• 2006

The electrolytic reduction of spent oxide fuel involves the liberation of oxygen in a molten LiCl electrolyte, which results in a chemically aggressive environment that is too corrosive for typical structural materials. So, it is essential to choose the optimum material for the process equipment handling molten salt. In this study, corrosion behavior of Inconel 713LC, MA 754, X-750 and 718 in the molten salt $LiCl-Li_2O$ under an oxidizing atmosphere was investigated at $650^{\circ}C$ for $72{\sim}216$ hours. Inconel 713LC alloy showed the highest corrosion resistance among the examined alloys. Corrosion products of Inconel 713LC were $Cr_2O_3,\;NiCr_2O_4$ and NiO, and those of Inconel MA 754 were $Cr_2O_3\;and\;Li_2Ni_8O_{10}$ while $Cr_2O_3,\;NiFe_2O_4\;and\;CrNbO_4$ were produced from Inconel 718. Also, corrosion products of Inconel X-750 were found to be $Cr_2O_3,\;NiFe_2O_4\;and\;(Cr,Nb,Ti)O_2$. Inconel 713LC showed local corrosion behavior and Inconel MA 754, 718, X-750 showed uniform corrosion behavior.