• Journal of Periodontal and Implant Science
• /
• v.34 no.1
• /
• pp.1-17
• /
• 2004

It is improtant that performing prophylaxis procedure on an infected implant surface in order to treat peri-implantitis should not change the surface roughness and composition, so that the surface can be recovered to almost same condition as initial implant surface. This thesis, therefore, studied an effect of various oral hygiene instrument on implant surface. A surface roughness measurement instrument and an infection electron microscope were used to observe a change on surface. The purpose of this study was to obtain a clinical guidelines during implant care and peri-implantitis treatment. The result were as follows 1. Ra values (surface roughness value) at experimental group 1, group 2, and group 5 were increased significantly as compared with comparison group(p<0.05). 2. When compared experimental group 1 with each experimental groups at which prohylaxis procedure was performed, mean values of Ra at experimental group 2, group 3, group 6, and group 7 were decreased significantly(p<0.05). 3. Mean value of Ra was lowest at experimental group 2, and highest at experimental group 2, and highest at experimental group 5. 4. Analysis of SEM showed that was significant surface change at experimental group 2, group 3, group 4, group 5, and group 6 as compared with comparison group(X1000). 5. Analysis fo EDX showed that a quantity of Ti on surface for experimental group 6 was very similar to that for comparison group. In conclusion, air-powder abrasive and citric acid, plastic instrument are safe methods to use for performing prophylaxis procedure on implant care or for cleaning and sterilization process on treatment of peri-implantitis, based on the result that those method did not affect implant surface roughness and Ti composition.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.123-126
• /
• 2005

Barium Titanate (BT) powders were synthesized by solvothermal method with an ethanol as a solvent. The average particle size was increased with the feedstock concentration: the size was 59 nm at $6.25{\times}10^{-2}$ M and 89 nm at 0.5 M. The sample obtained at 0.5 M concentration was analysed by Rietveld refinement and the mole fraction of tetragonal phase was $75.5\%$ and lattice parameter of tetragonal phase was a=0.3999 (nm), c=0.4032 (nm), and cubic phase was a=0.4015 (nm). TEM analysis for the samples with condition of annealing at $500^{\circ}C$ for I h showed that hydroxyl ions on oxygen sites were not found for these experimental conditions.

• Applied Chemistry for Engineering
• /
• v.5 no.4
• /
• pp.714-721
• /
• 1994

Titanium and zirconium-containing MFI type zeolites have been prepared hydrothermally. Incorporation of titanium or zirconium into the framework of zeolite has been demonstrated by XRD, FT-IR, $^{29}Si$ MAS NMR analysis, and the catalytic benzene hydroxylation or n-hexane oxidation was used for checking the properties of catalysts. Pure titania and zirconia powder showed no catalytic activity at all for these reactions but Ti and Zr modified zeolite had the high activities in both reactions. The catalytic activity strongly depended on the kind of solvents, and the conversion of benzene or n-hexane increased with the increasing content of Ti and Zr in zeolites.

• Journal of the Korean Ceramic Society
• /
• v.38 no.9
• /
• pp.860-865
• /
• 2001

After manufacturing 2mol% CdO substitute $0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.95Pb(Zr_{0.52}Ti_{0.48})O_3$ piezoelectric ceramics powder as starting material, to manufacture green sheets using Doctor Blade method. The optimum composition of slurry was studied. Moreover, the sintering properties and the dielectric and piezoelectric properties with variation a thickness of the manufactured sheets were investigated. The optimum of slurry was investigated by the rheology with addition of additives, the sintering condition was decided by TGA. And the properties of sheet were investigated through SEM. XRD. The optimum of slurry was the stablest at dispersant 3.0 wt% to solid loading 30vol%. After, at addition of binder/plasticizer(0.75/0.25) 3.0wt%, viscosity was 7.55Pa${\cdot}$s. The dielectric and piezoelectric properties of the sheet were increased a little with the increasing of sintering temperature but were not variable with variation of sheet thickness.

• Nuclear Engineering and Technology
• /
• v.51 no.8
• /
• pp.2042-2049
• /
• 2019

Ten gizzard and three flesh samples of the broiler were collected from different locations in Tehsil Gujar Khan District Rawalpindi, Pakistan. The samples were dried, crushed and ground. Pellets were prepared by pressing the powder of the samples and that of the Bovine liver 1577c reference material obtained from NIST, USA. Proton induced X-ray emission (PIXE) installed at National Center for Physics, Islamabad, Pakistan has been used as a reliable and improved technique to determine concentration of various major/trace and toxic elements e.g. S, Cl, K, Ca, Cl, Fe, Cu, Mn, Co, Zn, Ti, Cd, Ga, Cr, V and Ni, in the Gizzard and Flesh samples of the broiler. The concentrations of all the detected elements in the samples are statistically significant. The certified and measured values of the elements in the reference material were in agreement with each other within a deviation of 7%. S, Cl, K and Ca are within tolerable limits and are good for human consumption. Ti, V, Cr, Mn, Fe, Co, Ni, Cu and Zn were more than the acceptable limits of World Health Organization, WHO whereas Ga, As, Sn, Sb and Pb are not detected in most of the samples.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.2
• /
• pp.176-184
• /
• 1993

The glasses, which the $\beta$-spodumene as the principal crystalline phase could be precipitated, were melted by adding >, $P_2O_5, TiO_2, ZrO_2 in the Li_2O-Al_2O_3-SiO_2$ system. In order to achieve the glass-ceramic body of near-theoritical density by sintering method, the optimum condition of heat treatment, the effect of glass powder size and the properties were investigated by DTA, XRD, bulk density, thermal expansion and SEM. Addition of $P_20_5$ imProved the tendency of sintering and the sample with 9wt% $P_20_5$ content was the most dense OOdy by sintering method. The optimum condition of heat treatmemt was sintered for densitification at $740^{\circ}C$ and crystallized at $950^{\circ}C$. In the optimum condition, the relative density was above 90% and the thermal expansion was negative about $-1{\times}10^{-7}/^{\circ}C$.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.445-451
• /
• 2016

It is very important to obtain non-agglomerated nano particle state for practical application of nano technology. In order to improve the functionality of products using nano particles, more precise control of particle size distribution is required in their synthesis process. However, synthesized nano particles are agglomerated easily due to physical and chemical reasons, and it then veils unique properties of the nano particles and causes some troubles in their practical application. In this study, a separation method for nano particles from suspension by using the droplets as the separation space was proposed. Using the suspension of 0.002 wt. % with $TiO_2$ powder, the particle size distribution of nano particles in the recollected suspension was measured. From the results, it was confirmed that it is possible to separate and to recollect the nano particles monodispersed by using the suggested method.

• Journal of Convergence for Information Technology
• /
• v.7 no.5
• /
• pp.123-128
• /
• 2017

Nanostructured materials have received attention due to their unique electronic, optical, optoelectrical, and magnetic properties as a results of their large surface-to-volume ratio and quantum confinement effects. Thermal chemical vapor deposition process has attracted much attention due to the synthesis capability of various structured nanomaterials during the growth of nanostructures. In this study, silicon oxide nanowires were grown on Si\$SiO_2$(300 nm)\Pt(5~40 nm) substrates by two-zone thermal chemical vapor deposition with the source material $TiO_2$ powder via vapor-liquid-solid process. The morphology and crystallographic properties of the grown silicon oxide nanowires were characterized by field-emission scanning electron microscope and transmission electron microscope. As results of analysis, the morphology, diameter and length, of the grown silicon oxide nanowires are depend on the thickness of the catalyst films. The grown silicon oxide nanowires exhibit amorphous phase.

• Transactions of the Korean hydrogen and new energy society
• /
• v.11 no.4
• /
• pp.189-202
• /
• 2000

$AB_2$ type Zr-based Laves phases alloys have been studied for potential application as a negative electrode in a Ni-MH battery. The $AB_2$-type electrodes have a much higher energy density than $AB_5$-type electrodes per weight, however they have some disadvantages such as poor activation behavior and cycle life etc. Nonetheless, the $AB_2$-type electrodes have been studied very extensively due to their high energy density. In this study, in order to develop the cycle life, the Mn of $AB_2$ alloy composition was substituted partially by Mo. The alloys were melted by arc furnace and remelted 4-5 times for homogeneity. The alloy powder was used below 200-325 mesh for experiments. The structures and phases of the alloys were analyzed by XRD, SEM and EDS, and measured the curve of a pressure-composition isotherms. The electrodes were prepared by cold pressing of the copper-coated(25 wt%) alloy powders, and tested by a half cell. The results are summarized as follows. The cycle life was improved with the increase of Mo amount in $Zr_{1-x}Ti_xV_{0.4}Ni_{1.2}Mn_{0.4}Mo_y$(x=0.3, 0.4) and the activation was faster, whereas the discharge capacity decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.873-876
• /
• 2000

Characteristics of piezoelectric thick films prepared by screen printing method were investigated. The piezoelectric thick films were printed using Pb(Mg,Nb)O$_3$-Pb(Zr,Ti)O$_3$system. The lower electrodes were coated with various thickness of Ag-Pd by screen printing to investigate the effect as a diffusion barrier and deposited with Pt by sputtering on Ag-Pd. The ceramic paste was prepared by mixing powder and binder with various ratios using three roll miller. The fabricated thick films were burned out at 650$^{\circ}C$ and sintered at 950$^{\circ}C$ in the O$_2$condition for each 20, 60min after printing with 350mesh screen. The thickness of piezoelectric thick film was 15∼20 $\mu\textrm{m}$ and the Ag-Pd electrode acted as a diffusion barrier above 3 $\mu\textrm{m}$ thickness. When the lower electrode Ag-Pd was 6 $\mu\textrm{m}$ and the piezoelectric thick films were sintered by 2nd step (650$^{\circ}C$/20min and 950$^{\circ}C$/1h) using paste mixed Pb(Mg,Nb)O$_3$-Pb(Zr,Ti)O$_3$$.$ MnO$_2$+ Bi$_2$O$_3$. V$_2$O$\_$5/ and binder in the ratio of 70:30, the remnant polarization of thick film was 9.1 ${\mu}$C /cm$^2$.