• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.386-390
• /
• 2015

Fe-base superalloy powders with $Y_2O_3$ dispersion were prepared by high energy ball milling, followed by spark plasma sintering for consolidation. High-purity elemental powders with different Fe powder sizes of 24 and 50 mm were used for the preparation of $Fe-20Cr-4.5Al-0.5Ti-O.5Y_2O_3$ powder mixtures (wt%). The milling process of the powders was carried out in a horizontal rotary ball mill using a stainless steel vial and balls. The milling times of 1 to 5 h by constant operation (350 rpm, ball-to-powder ratio of 30:1 in weight) or cycle operation (1300 rpm for 4 min and 900 rpm for 1 min, 15:1) were applied. Microstructural observation revealed that the crystalline size of Fe decreased with an increase in milling time by cyclic operation and was about 15 nm after 3 h, forming a FeCr alloy phase. The cyclic operation had an advantage over constant milling in that a smaller-agglomerated structure was obtained. The milled powders were sintered at $1100^{\circ}C$ for 30 min in vacuum. With an increase in milling time, the sintered specimen showed a more homogeneous microstructure. In addition, a homogenous distribution of Y-compound particles in the grain boundary was confirmed by EDX analysis.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.4
• /
• pp.181-184
• /
• 2017

Multilayer ceramics in which piezoelectric layers of $0.90Pb(Zr_{0.48}Ti_{0.52})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.05Pb(Zn_{1/3}Nb_{2/3})O_3$ (0.90PZT-0.05PMS-0.05PZN) stack alternately with silver electrode layers were prepared by an advanced low-temperature co-fired ceramic (LTCC) method. The electrical properties and bonding strength of the multilayers were associated with the interface morphologies between the piezoelectric and silver-electrode layers. Usually, the inner silver electrodes are fabricated by sintering silver paste in multi-layer stacks. To improve the interface bonding strength, piezoelectric powders of 0.90PZT-0.05PMS-0.05PZN with an average particle size of $23{\mu}m$ were added to silver paste to form a gradient interface. SEM observation indicated clear interfaces in multilayer ceramics without powder addition. With the increase of piezoelectric powder addition in the silver paste, gradient interfaces were successfully obtained. The multilayer ceramics with gradient interfaces present greater bonding strength as well as excellent piezoelectric properties for 30~40 wt% of added powder. On the other hand, over addition greatly increased the resistance of the inner silver electrodes, leading to a piezoelectric behavior like that of bulk ceramics in multilayers.

• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.233-240
• /
• 2019

This study analyzes the mechanical properties, including the attrition rate, of $50{\mu}m$ size yttria-stabilized zirconia (YSZ) beads with different microstructures and high-energy milling conditions. The yttria distribution in the grain and grain-boundary of the fully sintered beads relates closely to Vickers hardness and the attrition rate of the YSZ beads. Grain size, fractured surfaces, and yttrium distribution are analyzed by electronic microscopes. For standardization and a reliable comparison of the attrition rate of zirconia beads with different conditions, Zr content in milled ceramic powder is analyzed and calculated by X-ray Fluorescence Spectrometer(XRF) instead of directly measuring the weight change of milled YSZ beads. The beads with small grain sizes sintered at lower temperature exhibit a higher Vickers hardness and lower attrition rate. The attrition rate of $50{\mu}m$ YSZ beads is measured and compared with the various materials properties of ceramic powders used for high-energy milling. The attrition rate of beads appears to be closely related to the Vickers hardness of ceramic materials used for milling, and demonstrates more than a 10 times higher attrition rate with Alumina(Hv ~1650) powder than $BaTiO_3$ powder (Hv ~315).

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.30 no.2
• /
• pp.181-187
• /
• 2004

Preparations of mesoporous materials using various templates and their applicability have been intensively investigated for many years. We studied on synthesizing mesoporous Ti02 with pores in which sensitive compounds having weak physico-chemical properties such as thermal or UV irradiation and low solubility in solvent are trapped. Prior to trapping OMC in the pores of mesoporous titania, OMC was nano-emulsified in O/W system using Lecithin. Thereafter the OMC was trapped in the pores of mesoporous titania using sol-gel method. Main focus of this work is to prepare OMC-trapped mesoporous titania and to trace the stability and solubility of nano-emulsified OMC in the pores of mesoporous titania, and compared with that of mesoporous silica. OMC-trapped mesoporous Inorganic-Organic hybrid titania showed higher factors in sun protecting and a skin penetration phenomenon was reduced.

• Journal of the Mineralogical Society of Korea
• /
• v.21 no.3
• /
• pp.247-259
• /
• 2008

$TiO_2$ coatings on kaolinite powders by sol-gel method were carried out using mixture of titanium isopropoxide, ethanol as solvent, HCl as a catalyst and $H_{2}O$ for hydrolysis. The mole ratio of reaction mixture, stirring time. aging time, crystallization time and crystallization temperature influenced to the crystallization of $TiO_2$ coated on kaolinite and metakaolinite Powders. Optimum condition for $TiO_2$ coatings on kaolinite was as follows; TIP 0.1 mol, $H_{2}O$ 0.15 mol, HCl 0.005 mol, ethanol 100 ml, raw kaolinite 50 g, stirring time 4 hrs, aging time 24 hrs, crystallization time 2 hrs and crystallization temperature $1050^{\circ}C$. The crystallinity of the anatase under optimum condition was about 17.61%. The anatase crystallinity of the $TiO_2$ coated on raw kaolinitc powders (17.61% at $1050^{\circ}C$) was higher at the lower calcination temperature compared with metakaolinite (17.39% at $1200^{\circ}C$).

• Membrane Journal
• /
• v.22 no.5
• /
• pp.359-368
• /
• 2012

For hybrid water treatment of high turbidity water, we used the hybrid module that was composed of photocatalyst packing between tubular membrane outside and module inside. Photocatalyst was PP (polypropylene) bead coated with $TiO_2$ powder by CVD (chemical vapor deposition) process. Water back-flushing of 10 sec was performed per every period of 10 min to minimize membrane fouling for modified solution was prepared with humic acid and kaolin. Resistance of membrane fouling ($R_f$) decreased as humic acid concentration changed from 10 mg/L to 2 mg/L, and finally the highest total permeate volume ($V_T$) could be obtained at 2 mg/L, which was the same with the previous results. Then, treatment efficiencies of turbidity and humic acid were above 98.9% and 88.7%, respectively. As results of treatment portions of UF, UF + $TiO_2$, and UF + $TiO_2$ + UV processes, turbidity was treated little by photocatalyst adsorption, and photo-oxidation. However, treatment portions of humic acid by adsorption and photo-oxidation were 2.5% and 12.3%, respectively. Compared with the previous results, treatment portions of humic acid by adsorption and photo-oxidation were different depending on membrane material and pore size. As simplified the process, the membrane fouling resistance after 180 minutes' operation ($R_{f,180}$) increased and the final permeate flux decreased a little.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.236-240
• /
• 2007

In order to control the microstructure of amorphous/crystalline composites, gas atomized $Cu_{54}Ni_{6}Zr_{22}Ti_{18}$ metallic glass powders wrapped in a crystalline brass were extruded repeatedly. The size of microstructure in the resultant composites was varied depending on the pass of extrusion as well as on the area reduction ratio. The microstructure could be estimated using an equation of $r_n=r_{n-1}/R^{1/2}$, where R is reduction ratio and $r_n$ is the resultant radius of the extruded bar after n pass. Theory of microstructural refinement as well as the relationship between the resultant microstructures and mechanical properties was discussed.

• Archives of Pharmacal Research
• /
• v.16 no.1
• /
• pp.50-56
• /
• 1993

The microencapsulation of sodium naproxen with Eudragit. RS was studied by coacrtvation/phase separation process using Span 80 in mineral oil/acetone system. Various factors which affect the mciroencapsulation, e.g., stirring speed, and surfactant concentraction, Eudagit RS concentration and loading drug amounts were examined. For the evaluation of the prepared microcapsules, release rate, particle size distribution and surface appearance as well as in vivo test were carried out. The addition of n-hexane and freezing of microcapsules accelerated the hardening of microcapsules. The optimum concentration of Span 80 ti prepare the smallest microcapsules was the same value with the CMC of Span 80 in solvent system. When 1.5% (w/w) Span 80 was used, the smallest microcapsules were formed $(30.02\pm5.05\mu$ in diameter) belonging to the powder category showing smooth, round and uniform surface. The release of sodium naproxen was retarded by microencapsulation with Eudragit RS. The Eudragit RS microcapsules showed significantly increased AUC and MRT and deceased Cl/F in rabbits.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.291-291
• /
• 2009

ZnS:Mn/Cu,Cl 계 나노 형광체의 특성을 살펴보았다. 실험에서는 ZnS:Mn 과 ZnS:Cu,Cl 형광체 파우더를 이용하여 밀링을 통하여 분쇄하여 EL 소자를 제작하였다. 형광체 파우더를 볼밀에 $\Phi5mm$의 지르코나이 볼과 에탄올과 함께 넣고 2, 4, 6, 8, 10일간 밀링을 하였다. 밀링한 형광체 파우더를 SEM을 통하여 파우더의 사이즈를 관찰하였다. 또 이 파우더를 이용하여 EL 소자를 제작하였다. 소자의 구조는 기판은 알루미나 기판을, 하부 전극은 Au, 유전체는 $BaTiO_3$ 유전체 페이스트를 사용하였으며, 형광체 적층 후 ITO 전극을 스퍼터를 이용하여 증착하여 제작하였다. 제작한 소자를 이용하여 소자의 휘도 등 발광 특성을 살펴보았다.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.517-524
• /
• 1992

For the present study two alumina bodies were prepared. The sinter-aid alumina body(SAA) was made by conventional sinter-process using sintering additives of TiO2 & MgO/CaO and the reaction-bonded alumina (RBA) made from Al-Al2O3 mixed powder. A comparison was made between those two bodies and this investigation seeks to evaluate their microstructure, physical properties and material's reliability as well as their fracture behaviour. In spite of its considerable microstructural densification accompanied by sintering shrinkage, SAA is largely inferior to RBA in fracture strength. However, SAA shows a somewhat higher m-value than RBA in respect to the material's reliability, the Weibull modulus(m). RBA, which has high fracture strength, shows much longer lifetime under static loading than SAA. Though, as with m of fracture strength, the reliability(mt) of lifetime prediction in RBA is less high than of SAA.