• 한국재료학회지
• /
• 제25권8호
• /
• pp.398-402
• /
• 2015

Fundamental studies of microstructural changes and high temperature deformation of titanium aluminide (TiAl) were conducted from the view point of the effect of Al content in order to develop the manufacturing process of TiAl. Microstructures in an as cast state consisted mainly of lamellar structure irrespective of Al content. By homogenization at 1473 K, the microstructures of Ti-49Al and Ti-51Al were transformed into an equiaxial structure which was composed of ${\gamma}$-TiAl, while the lamellar structure that was observed in Ti-46Al and Ti-47Al was much more stable. We found that the reduction of Al content suppressed the formation of equiaxial grains and resulted in a microstructure of only a lamellar structure. On Ti-49Al and Ti-51Al, dynamic recrystallization occurred during high temperature deformation, and the microstructure was transformed into a fine equiaxial one, while the microstructures of Ti-46Al and Ti-47Al contained few recrystallized grains and consisted mainly of a deformed lamellar structure. We observed that on the low-Al alloys the lamellar structure under hard mode deformation conditions deformed as kink observed B2-NiAl. High temperature deformation characteristics of TiAl were strongly affected by Al content. An increase of Al content resulted in a decrease of peak stress and activation energy for plastic deformation and an increase of the recrystallization ratio in TiAl.

• 한국재료학회지
• /
• 제2권6호
• /
• pp.436-442
• /
• 1992

레이저빔에 의한 철강재의 Ti 표면합금화에 미치는 C함량의 영향을 관찰하였다. 철강재상에 Ti 코팅 후 레이저빔 조사시 질소를 취입가스로 사용하면 부분적으로 TiN과 F$e_2$Ti가 형성된다. 저탄소강의 경우 Ti함량의 증가에 따라 임계냉각 속도의 증가로 마르텐사이트화가 억제된다. 고탄소강의 경우 Ti의 함량이 1.5%정도 임에도 훼라이트 조직이 형성되지 않고 마르텐사이트 조직이 형성되어 경화된다. 그리고 고탄소강의 Ti 표면합금층 형성에 부분적인 TiC의 석출이 있어 더욱 경도를 증가시키는 것으로 생각된다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.352-353
• /
• 2006

The effect of TiC content on oxidation behavior of the sintered WC-TiC-TaC alloys with 2 mass% TaC and different TiC amounts of 3-45 mass% was investigated through oxidation tests in air at 973K. As a result of the tests, it was revealed that with increasing TiC content in the alloys, mass changes caused by oxidation and thickness of the scale decreased. Thus, it is considered that the main component of the scales changed gradually from $WO_3$ to $TiO_2$ with increasing TiC content in the alloys, and oxygen diffusion through the scale to the alloys was inhibited gradually.

• Corrosion Science and Technology
• /
• 제12권1호
• /
• pp.50-55
• /
• 2013

The purpose of this study was to investigate corrosion characteristics of Ti-xTa alloys with Ta contents. Ti-xTa alloys used as samples (x=30, 40%) were arc-melted under argon atmosphere of 99.9% purity. Ti-xTa alloys were homogenized for 12hr at $1000^{\circ}C$ and then water quenched. The surface characteristics of Ti-xTa alloys were investigated using optical microscopy (OM) and X-ray diffractometer (XRD). The anodic corrosion behaviors of the specimens were examined through potentiodynamic, potentiostatic and galvanostatic test in 0.9 % NaCl solution at $36.5{\pm}1^{\circ}C$. After corrosion test, the surface characteristics of Ti-xTa alloys were investigated using OM. The microstructure of Ti-Ta alloy showed the beta structure with Ta content. The corrosion resistance of Ti alloy was improved by increasing Ta content and the corrosion morphology of Ti-Ta alloy showed that the site attacked by chloride ion decreased from the active to passive region with Ta content. Potential of Ti-40Ta alloy increased as time increased, whereas, current density of Ti-40Ta alloy decreased as time increased compared to Ti-30 alloy.

• Corrosion Science and Technology
• /
• 제22권1호
• /
• pp.64-72
• /
• 2023

Ni-Ti shape memory alloy for dental nerve treatment devices was prepared by adding Mo to Ni-Ti alloy to improve flexibility and fatigue fracture characteristics and simultaneously increase corrosion resistance. Surface properties of the alloy were evaluated. Microstructure analysis of the Ni-Ti-xMo alloy revealed that the amount of needle-like structure increased with increasing Mo content. The shape of the precipitate showed a pattern in which a long needle-like structure gradually disappeared and changed into a small spherical shape. As a result of XRD analysis of the Ni-Ti-xMo alloy, R-phase structure appeared as Mo was added. R-phase and B2 structure were mainly observed. As a result of DSC analysis, phase transformation of the Ti-Ni-Mo alloy showed a two-step phase change of B2-R-B19' transformation with two exothermic peaks and one endothermic peak. As Mo content increased, R-phase formation temperature gradually decreased. As a result of measuring surface hardness of the Ti-Ni-Mo alloy, change in hardness value due to the phase change tended to decrease with increasing Mo content. As a result of the corrosion test, the corrosion potential and pitting potential increased while the current density tended to decrease with increasing Mo content.

• 한국표면공학회지
• /
• 제33권2호
• /
• pp.93-100
• /
• 2000

Effects of Ti content and Ti underlayer on the pitting behavior of TiN coated AISI 304 stainless steel have been studied. The stainless steel containing 0.1~1.0wt% Ti were melted with a vacuum melting furnace and heat treated at $1050^{\circ}C$ for 1hr for solutionization. The specimen were coated with l$\mu\textrm{m}$ and 2$\mu\textrm{m}$ thickness of Ti and TiN by E-beam PVD method. The microstructure and phase analysis were conducted by using XRD, XPS and SEM with these specimen. XRD patterns shows that in TiN single-layer only the TiN (111) Peak is major and the other peaks are very weak, but in Ti/TiN double-layer TiN (220) and TiN (200) peaks are developed. It is observed that the surface of coating is covered with titanium oxide (TiO$_2$) and titanium oxynitride ($TiO_2$N) as well as TiN. Corrosion potential on the anodic polarization curve measured in HCl solution increase in proportion to the Ti content of substrate and by a presence of the Ti underlayer, whereas corrosion and passivation current densities are not affected by either of them. The number and size of pits decrease with increasing Ti content and a presence of the coated Ti film as underlayer in the TiN coated stainless steel.

• 한국세라믹학회지
• /
• 제53권2호
• /
• pp.139-144
• /
• 2016

The dependence of the microwave dielectric properties of the glass-ceramic composite $0.9CaMgSi_2O_6-0.1MgSiO_3$ on the crystallization behaviour was investigated as functions of the $TiO_2$ content and heat-treatment temperature. The crystallization behaviour of the specimens was evaluated via a combination of the Rietveld and reference-intensity ratio methods. For specimens with a $TiO_2$ content of up to 1 wt.%, a monoclinic diopside phase was formed, whereas a secondary $TiO_2$ phase was formed with further increases in the $TiO_2$ content. The quality factor (Qf) of the specimens was strongly dependent on the degree of crystallization. The highest Qf value was obtained with a $TiO_2$ content of 0.5 wt.%, which was improved by increasing the heat-treatment temperature. The dielectric constant (K) was affected by the size of the crystallites and the $TiO_2$ content. The temperature coefficient of the resonant frequency (TCF) was nearly constant for all of the specimens, regardless of the $TiO_2$ content or heattreatment temperature.

• 대한의용생체공학회:의공학회지
• /
• 제14권3호
• /
• pp.283-290
• /
• 1993

In thls study, the effects of the composltional change of cast Ni-Ti alloys on its characteristics including mechanical properties, phase transformation temperature, and ion releasing rate were investigated. brittle:behavior was shown in the stress-strain curve of the alloy containing low Ti content (Ni-44.0%Ti). By increasing the Ti content, the trend in stress-strain curves changed from that of superelasticity to that of shape memory effect(Ni-44.4%Ti, Ni-45.1%Ti, Ni-45, 5%Ti). Phase transformation temperature ($A_f, {\;}M_5$ point) increased with increasing the Ti content. lon releasing rate of four types of Mi-Ti alloys was very low compared to that of the dental commerical Ni-Cr alloy.

• 한국결정학회지
• /
• 제6권2호
• /
• pp.111-117
• /
• 1995

화학증착법에 의해 TiO2 박막을 Si-wafer(100)위에 제조하였다. Titanium tetraisopropoxide (TTIP)를 출발물질로 하여 200-500℃의 온도범위에서 증착을 행하였다. 증착된 박막의 두께는 Ellipsometry 및 SEM을 사용하여 측정하였으며, 산소의 함량에 따른 증착층의 성분분석은 ESCA를 사용하였다. TiO2 박막의 증착속도는 산소의 함량에 따라 증가하였고, 반응가스인 산소를 공급하지 않았을 때 증착층내에 불순물로 탄소가 존재하였으며, 증착층의 성분은 내부로 갈수록 TiO2에서 Ti로 변하였다. 산소를 600scm 공급하였을 때 증착층내에 소량의 탄소가 존재하였으며, 증착층의 성분은 내부로 갈수록 TiO2에서 TiO, Ti로 됨을 알 수 있었다. 산소를 1200scm공급하였을 때 증착층내에 탄소가 존재하지 않았으며, 증착층 성분은 표면에는 TiO2를 이루나 증착층 내부로 갈수록 Ti복합화합물을 이루고 있었다.

• Elastomers and Composites
• /
• 제57권1호
• /
• pp.1-8
• /
• 2022

In this study, the photo-deposition method was used to introduce Ag onto the surface of TiO₂ to synthesize an Ag-TiO₂ composite. The effects of the varying amounts of AgNO₃ precursor and annealing time periods on the Ag content in the composites, as well as their antibacterial characteristics under visible light conditions were studied. SEM analysis revealed the spherical morphology of the Ag-TiO₂ composite. Compared with TiO₂, the Ag particles were too small to be observed. An XPS analysis of the Ag-TiO₂ surface confirmed the Ag content and showed the peak intensities for elements such as Ag, Ti, O, C, and Si. The highest Ag content was observed when 33.3 wt.% of AgNO₃ and an annealing time of 6 h were employed; this was the optimum annealing time for Ti-Ag-O bonding, in that the lowest number of O bonds and the highest number of Ag bonds were confirmed by XPS analysis. Superior antibacterial properties against Bacillus and Escherichia coli, in addition to the widest inhibition zones were exhibited by the Ag-TiO₂ composite with an increased Ag content in a disk diffusion test, the bacterial reduction rate against Staphylococcus aureus and Escherichia coli being 99.9%.