• 대한기계학회논문집B
• /
• 제26권11호
• /
• pp.1496-1502
• /
• 2002

An Altitude Engine Test Facility(AETF) was built at the Korea Aerospace Research Institute in October 1999 and has been being operated for altitude testing of gas turbine engines of 3,000 Ibf class or less. The AETF has been calibrated using several engines such as J69 of Teledyne Co. as a facility checkout engine. Uncertainty analyses on the air flow rate and thrust were performed using the test results, according to ASME PTC 19.1-1998. Several modifications on the facility and test method were made in order to improve the measurement uncertainty to a satisfactory level over the whole operating envelop. Spatial distributions of pressure and temperature were measured, sensors were substituted by more accurate ones, inlet duct was modified to refine the flow quality, and pressure control logic was revised to remove the cell pressure fluctuation. As a result, the uncertainty of the air flow measurement was improved by 0.1% over all the test conditions, and the net thrust measurement by up to 3%. The improved measurement uncertainties of air flow and thrust are 0.68～O.73% and 0.4～1.3%, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.25-27
• /
• 2003

In this paper the instantaneous thrust of a linear induction motor(LIM) with cage-type secondary is estimated by the line voltages and phase currents measurement when the LIM is fed by PWM inverter. The estimated thrust values according to various input frequencies are compared with the measured ones.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1599-1604
• /
• 2007

LIMs propelling the MAGLEV which has been developed in Korea have 3-series and 2-parallel connection, so that 6 LIMs per one vehicle are fed by one inverter. Thrust performance of the parallel-operated LIMs can be different from each other because of variant magnetic air gaps and electrical impedance. The thrust difference between the parallel LIMs cause a twist force on the vehicle. This paper proposes an algorithm to measure thrust of the parallel-operated LIMs. The method uses a digital signal processor(TMS320F2812), voltage and current sensors. As a result, thrust, flux and currents of the parallel-operated small LIMs which are manufactured in our laboratory are monitored by the developed measurement system.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.358-362
• /
• 2005

축추력의 효과적인 제어는 터보펌프 개발의 핵심 기술 중 하나이다. 현재 개발 중인 액체로켓엔진용 연료펌프의 안정성을 입증하기 위해 축추력 측정 장치를 개발하고 수류 시험을 실시하였다. 시험 결과, 연료펌프는 설계 유량에서 펌프 베어링의 축방향 하중 요구 조건을 만족하였다. 또한 이차 유로의 오리피스를 통해 연료펌프에 대한 축추력 제어가 가능한 것을 확인하였다.

• Journal of Electrical Engineering and Technology
• /
• 제2권1호
• /
• pp.50-54
• /
• 2007

In this paper, a dual-servo type VCM (Voice Coil Motor) for the measuring of nano-level displacement and small thrust is proposed and developed. The shape of VCM for improving the resolution of displacement and ensuring a large displacement are presented. The FEM (finite element method) is utilized to analyze the characteristics of VCM that produces linear driving thrust and satisfies the thrust that the measurement system requires. The Prototype is fabricated and an experiment is performed in order to measure displacement. As a result of simulation and testing, the proposed VCM shows the applicable possibility for a nano-level measurement system.

• 한국정밀공학회지
• /
• 제15권8호
• /
• pp.183-192
• /
• 1998

In this paper, we measure the back-EMF and the thrust of a linear brushless DC motor along the relative position between coils and magnets in various speed environments in order to obtain the back-EMF and the thrust as a function of a motor position. The measured back-EMF function and thrust function of the position differ from the analytical ones within 5%. The measured back-EMF and thrust function can, then, be employed in controlling the thrust ripple of the linear motor. Furthermore, to minimize the torque ripple of the linear motor, we suggest the design method to shape the back-EMF and thrust function of the linear motor.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.39-42
• /
• 2008

In the case of the general helicopter among rotorcraft, length of the rotor blade for thrust-generation is longer than that of fuselage and tail rotor is required in order to compensate moment of the fuselage. For those reasons, enough space for take-off and landing should be secured and an accessibility for building is low. Also, the accidents caused by tail rotor occur frequently. However, the case of counter-rotating has merits that tail rotor is unnecessary as well as length of the rotor blade can be shortened but has a weakness that the weight of body is increased. In the present study, aerodynamic force measurement on single rotor system equipped with NACA0012 airfoil, which has aspect ratio of 6 and chord length of 35.5 mm, was carried out. And measurement was conducted with blade which has a half size of the former blade by using single motor counter-rotating. Aerodynamic force measurement was acquired by using 6-component balances and coefficients of thrust and power were derived along the pitch angle varying from 0$^{\circ}$ to 90$^{\circ}$ with the increment of 10$^{\circ}$. Those aerodynamic force data will be utilized for the design and production of brand-new counter-rotating rotor blade system which has same thrust with single blade system and provides a good accessibility to building by reducing its blade length.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.574-577
• /
• 2012

추력 측정은 액체로켓엔진 개발시험 시, 특히 연소기 개발시험 시에 성능 판단을 위한 매우 중요한 항목이다. 측정하기 어려운 경우에는 연소압을 통해 간접적으로 유추하는 방법을 쓰기도 하나 스탠드의 능력이 된다면 직접 측정하는 것이 필요하며 보다 더 정확하게 측정하기 위한 여러 가지 방안을 고려하게 된다. 본 논문에서는 국내 최초로 시도하는 액체로켓엔진 연소기의 수직형 연소시험설비에서 도입한 추력 측정 시스템에 대한 기본설계안을 소개한다.

• 한국정보통신학회논문지
• /
• 제13권10호
• /
• pp.2147-2153
• /
• 2009

저가격형으로 프로토타잎 하이브리드형 리니어 펄스 모터(LPM)가 편측형으로 설계되었다. 모터의 정특성 및 동특성 측정위한 측정기기를 설계 제안하였다. 실험측정결과 프로토타잎 리니어 펄스 모터의 정특성 및 동특성을 구체적인 추력의 값으로 확인하였다. 프로트타잎 리니어 펄스 모터를 구형파와 마이크로스텝 구동으로 구동하여 각각의 경우의 추력의 변화를 확인하였다. 실험결과 마이크로스텝구동방식에서 추력리플이 현저히 줄어든 것을 확인할 수 있었다.

• 한국추진공학회지
• /
• 제20권5호
• /
• pp.31-39
• /
• 2016

본 논문은 볼트 체결 강성이 추력 시험대에 미치는 영향을 연구한 것이다. 추력 시험대는 추진기관의 추력 성능을 평가하는 장비로 추력, 피치력, 요력(3 분력) 작용선에 대응하는 3 분력 계측선간의 평행도와 3 분력 계측선의 상호 직각도가 다분력 추력시험대의 성능을 좌우한다. 따라서 시험대의 초기 형상을 작동 상태에서 유지시키는 것이 추력 시험대의 핵심 기능이다. 본 논문에서는 추력 시험대의 볼트 체결과 로드셀 트레인의 나사 체결의 공차 정확도가 추력 시험대에 미치는 현상을 규명하고 이를 극복하는 방안을 제시하였다.