• 한국운동역학회지
• /
• 제17권1호
• /
• pp.29-39
• /
• 2007

This study were obtained elapsed time phase-by-phases, displacement, user angle, velocity and angular velocity to analyse kinematically contributing factors at impact of forehand drive motion, on targeting three male players. The results of the study were presented as follows; In the forehand drive swing, the elapsed time by phases was a total of .52 seconds: .30 seconds from backswing to impact and .22 seconds from impact to follow-through, Considering the mean change in locations of COM of each(part$\rightarrow$body segment) at impact, racket head, left shoulder, right wrist and left hip, the left-right directions(X-axis) were showm to be each $.61{\pm}.03$, $1.19{\pm}.08$, $.66{\pm}.03$, $.94{\pm}.06$, and $.45{\pm}.03m$. The displacement differences of COM of each body segment were shown to be -.57, -.05, -.33, and .16m. For the vertical direction(Z-axis), the center of mass was lowest at impact and highest at E3. For the displacement of the right wrist on the left hip, the right wrist moved to .82m to the lower direction without change in the locations of the hip from E1 from E2. When the left hip moved .02m from E2 to E3, the right wrist moved .7m in the upper direction. In respect to the velocity of each body segment, the hip and the shoulder joint accelerated and then the wrist followed. Then the right wrists of all the subjects and their racket heads showed maximum speed, and an effective swing was observed. At the angle of each part, the angle of the right wrist was the smallest at the backswing and the largest at the moment of the impact. Then it increased gradually in the follow-through section. In respect of angular velocity for subject A, the hip moved and the largest change occurred. Immediately before the impact, the subject made a swing using his right wrist, his hip, and the shoulder joint, showing the maximum value, which was judged to be effective.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제5권2호
• /
• pp.115-126
• /
• 2017

본 논문은 특수 차량용 동력 전달계 부품인 구동축의 가속 수명 시험을 수행하는 것이다. 동력 전달계 부품의 수명 평가를 위하여 사용환경의 주행 부하 스펙트럼의 데이터가 필요하나, 특수 차량의 경우 부하 스펙트럼을 구할 수 없는 경우가 대부분이다. 따라서, 본 논문에서는 차량 데이터와 특수 주행로 조건에 기반하여 주행 부하 로드 스펙트럼을 모델링하고 시뮬레이션 하였다. 가속 수명 시험에는 역승 모델을 적용하였고, 마이너 법칙을 사용하여 등가 토크를 구하였으며, 구동축 가속 수명 시험을 위하여 교정 가속법을 사용하였다. 피로시험은 세 수준의 스트레스로 수행하였으며, 사용자 스트레스 수준의 수명은 외삽법을 사용하여 예측 하였고, 실제 시험 결과와 부하 스펙트럼 데이터와의 비교로 수명을 검증하였다.

• 전자공학회논문지SC
• /
• 제44권5호
• /
• pp.62-70
• /
• 2007

본 논문에서는 일정 토크영역에서 승압형 PFC 컨버터와 직접토크제어(DTC) 방법을 사용하여 BLDC 모터의 구동 시스템을 DSP(TMS320F2812)로 구현하였다. 기존의 6단계 PWM 전류제어와 달리 미리 정한 샘플시간 마다 간단한 look-up 표로부터 2상 도통 모드에 대한 인버터의 전압 상태 벡터를 설정함으로써 원하는 전류파형을 만들었으며 이로부터 기존의 전류제어기보다 훨씬 빠른 토크 응답특성을 얻을 수 있었다. 또한 BLDC 모터의 비 이상적인 사다리형 역기전력에 의해 발생되는 저주파 토크변동을 저감하기 위하여 위치 loop-up 표를 사용하였다. 아울러 역률을 보정하기 위해 승압형 PFC 컨버터를 구성하였고 이 때 전파 정류된 입력전압과 출력전압, 인덕터의 전류에 의해 평균전류모드 제어 방식으로 80 kHz마다 PWM 듀티(duty)가 조절 되도록 하였다. 이와 같이 복잡한 제어 알고리즘은 초고속 DSP의 출현으로 PFC와 DTC 알고리즘이 동시에 제어가 가능하며, 본 논문에서는 DTC 알고리즘을 구현할 때 DSP의 일반 범용의 출력포트를 사용하여 구현하였고 단지 PFC에서만 1개의 PWM을 사용하여 디지털 제어기를 구현하였다. 실험을 통해 DTC 알고리즘과 PFC 컨버터를 이용한 BLDC 모터 구동 시스템의 타당성과 효용성을 보였고, 실험결과로부터 PFC 컨버터를 사용하지 않았을 때는 역률이 약 0.77이었으나 PFC 컨버터를 사용하였을 때는 부하변동에 관계없이 약 0.9997로 크게 향상됨을 확인하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2010년도 춘계 학술논문 발표대회 1부
• /
• pp.33-36
• /
• 2010

The attention in construction Automation is getting higher since it could be the answer to the lack of skilled labor by decrease in construction population and aging which adversely affects productivity and quality in the construction site. We are on the way to develop a construction automation system adequate for domestic circumstances in Korea; it is called RCA(Robotic-crane based Construction Automation)system. Climbing hydraulic robots system is a part of RCA system and makes Construction factory(CF) climb through the guide rail on the core wall. The safety of climbing hydraulic robots system is at issue due to the overloaded weight of CF. Preventing this issue, present study did the design verification through the structural analysis and the simulation. Mock-up test also was done to analyze the drive performance of climbing hydraulic robots system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.186-189
• /
• 2001

In a precise control system, the Lu-Gre friction model has often been used to describe the nonlinear friction. For the XY table system with this friction model, we identified the friction parameters and designed nonlinear observer. The nonlinear friction effects could be removed within appropriate position tracking errors and control inputs through experiments. Also, we designed the nonmodel-based SMC system to compensate the nonlinear friction. Through experiments, it is shown that this method has the similar performance compared with the nonlinear observer system and is useful when friction parameters are hard to identify except the problem of input chattering.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1894-1899
• /
• 2000

The Roadway caused through Power Train engine vibration and bad ride comfort. It is very important to analyze the vibratory characteristics. The mathematical models on the Power Train, which is composed of engine-/transmission block, universal joint shaft, differential, rear axle arm and wheels, are developed and is verified by the experiments. This Paper describes the coupling influence occurred through a complete drive system for the power train. Dies study is carried out computationally with a calculation program and experimentally with the aid of the mode analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.908-909
• /
• 2008

A kind of fluorescent lamps CCFL(Cold Cathod Fluorescent Lamp) is used for backlight of LCD and the demand of backlight for TV is getting more. CCFL is also used in a backlight for TFT-LCD panel. BLU(Backlight Unit) has lots of components so it looks a electrical product. As the size of LCD display is larger with increasing of the demand, to drive CCFL inverter is more important. Therefore, a sort of modeling to drive 4 lamps with a transformer is used and we have a simulation test with proposed modeling so we can take some data from the test. The utility of the proposed modeling is verified through using for 30-inch LCD backlight with the data.

• Journal of Electrical Engineering and Technology
• /
• 제5권4호
• /
• pp.623-630
• /
• 2010

This paper presents the implementation and characteristic analysis of a drive system for a three-phase permanent magnet motor with independent excitation winding that is applicable for electric bicycles. The design features improves the phase current waveform, output power, and torque by using advance angle control. This adjusts the phase angle of each phase current in relation to back EMF. In addition, a DC-side PI current control is performed through PWM generation circuit using a low-cost one-chip microcontroller and a CPLD chip, resulting in reduced system costs. Finally, the validity of this control scheme for driving electric bicycles and output/torque improvement characteristics are verified through analysis and experimental results.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제2C권6호
• /
• pp.292-296
• /
• 2002

A new sustain driving method for the AC PDP is presented. In this driving method, the voltage source is connected to a storage capacitor, this storage capacitor charges an intermediate capacitor through LC resonance, and the panel is charged from the intermediate capacitor indirectly. In this way, the current flowing into the AC PDP when the sustain discharge occurs is reduced because the current is indirectly supplied from a capacitor, a limited source of charge. Thus, the input power to the output luminance efficiency is improved. Since the voltage supplied to the storage capacitor is doubled through LC resonance, this method call drive an AC PDP with a voltage source of about half of the voltage necessary in the conventional driving methods. The experiments showed that this charge-controlled driving method could drive ail AC PDP with a voltage source of as low as 107V. Using a panel of the conventional structure, luminous efficiency of 1.28 lm/W was achieved.

• 정보저장시스템학회논문집
• /
• 제1권1호
• /
• pp.84-92
• /
• 2005

This work presents the feasibility of shunt damping far vibration suppression of the rotating HDD disk-spindle system using piezoelectric bimorph. A target vibration mode which significantly restricts the recording density increment of the drive is determined through modal analysis and a piezoelectric bimorph is designed to suppress unwanted vibration. After deriving the two-dimensional generalized electromechanical coupling coefficient of the shunted drive, the shunt damping of the system is predicted by simulating the displacement transmissibility using the coefficient. In addition, optimal design process using sensitivity analysis is undertaken in order to improve the shunt damping of the system. The effectiveness of the proposed methodology is verified through experimental implementation by observing the vibration characteristics of the rotating disk-spindle system in frequency domain.