• Proceedings of the KSME Conference
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.641-646
• /
• 2000

This paper addresses a throttle/brake control law for stop and go cruise control systems which make the vehicle remain at a safe distance from a preceding vehicle according to the driver's preference, automatically slow down and come to a full stop behind a preceding vehicle. The uncertainties of vehicle model have been considered in the design of the control law. The effect of throttle/brake control has been investigated via simulations. The simulations were performed using a complete nonlinear vehicle model. The results indicate that the proposed throttle/brake control law can provide the stop and go cruise control system with a good distance tracking performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제7권6호
• /
• pp.72-81
• /
• 1999

A nonlinear engine torque and speed control algorithm using throttle angle control is developed with an engine load torque estimation algorithm. Three 3-dimensional nonlinear engine maps as a part of the nonlinear control algorithm are obtained from steady state engine dynamometer tests. An electric throttle actuator is developed using a stepper motor and a 8 bit micro-processor. The speed control and external load estimation algorithm are tested via engine speed control experiments, and show performance good enough for using various engine torque and speed control applications.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권1호
• /
• pp.97-103
• /
• 2013

This paper describes the characteristics of Electronic Throttle Controller (ETC) module in BLDC motor without the hall sensor for detecting a rotor position. The proposed ETC control system, which is mainly consisted of a BLDC motor, a throttle plate, a return spring and reduction gear, has a position sensor with an analogue voltage output on the throttle valve instead of BLDC motor for detecting the rotor position. So the additional commutation information is necessarily needed to control the ETC module. For this, the estimation method is applied. In order to improve and obtain the high resolution for the position control, it is generally needed to change the gear ratio of the module or the electrical switching method etc. In this paper, the 3-phase switching between successive commutations is adapted instead of the 2-phase switching that is conventionally used. In addition, the position control with a variable PI gain is applied to improve a dynamic response during a transient period and reduce vibration at a stop in case of matching position reference. The mentioned method can be used to estimate the commutation state and operate the high-precision position control for the ETC module and the high response characteristics. The validity of the proposed method is examined through the experimental results.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제13권6호
• /
• pp.113-119
• /
• 2005

The passenger car drivers want in general to feel good driveability, but they sometimes feel uncomfortable by shock and jerk phenomenon when they push or release acceleration pedal with clutch engaged. In this paper, the shock and jerk characteristics are studied on the vehicles of the throttle-by-wire system. With this system, the throttle is not directly controlled by drivers but via a microprocessor. So the control logic of the throttle is very important on tip-in and tip-out driveability. Experiments were carried out on two vehicles which show different control characteristics. The torque control logics were analyzed by measuring cylinder pressures. The results show that special torque control logic is needed at tip-in/out state for good driveability.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제4권3호
• /
• pp.92-101
• /
• 1996

In a gasoline engine, the characteristics of air flow is very important not only for the design of the intake system geometry bout also for the accurate measurement of the induction air mass. In this study, an air flow rate measurement of the induction air mass. In this study, an air flow rate measurement was conducted by using the hot wire flow meter at the upstream of the intake port and the throttle. At the upstream of the throttle, the overshoot phenomena of the air flow rate by fast throttle opening were analyzed with choked flow. At the upstream of the intake port, the cylinder variation of the air flow rate and the difference between fast throttle opening and closing were showed during the unsteady state by the throttle step change. The results of this study can be used for the design of the throttle valve geometry and cylinder by cylinder control.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2007년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.50-52
• /
• 2007

Throttle Control 장치는 차량의 지능화와 연료 절감의 이유로 기계식에서 전기적 신호의 연결로 구동시키는 시스템으로 발전하고 있다. 전기 전자 시스템을 도입한 ETC(Electronic Throttle Control)의 구성요소 중 필수적인 구동 원으로 DC모터를 많이 사용하고 있지만, DC모터는 정류작용 시 브러시의 스파크를 발생시키는 단점을 가진다. 이에 전기적 및 기계적 Noise가 적고 신뢰성이 높으며 수명이 긴 BLDC 모터의 개발이 필요하다. 이에 BLDC 모터의 기초 설계와 최적 설계를 통해 형상을 설계하고 이를 정자계 유한요소법을 이용하여 해석하고 목표 토크인 0.2[Nm]에 적합한 BLDC 모터를 설계하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제22권2호
• /
• pp.428-436
• /
• 1998

A TCS slip control system improves acceleration capability and steerability on slippery roads through engine torgue and/or brake torque control. This research mainly deals with the engine control algorithm via the adjustment of the engine throttle angle. The following new control strategy is proposed and investigated ; the TCS slip controller whose input is the difference between the desired driving wheel speed corresponding to the optimum slip ratio and the actual speed yields the target engine torque and then estimates the throttle angle based on the engine performance curve. Various simulation and hardware-in-the-loop simulation have been carried out. The results show the proposed strategy may compensate for the inherent nonlinearity between variation of the throttle angle and variation of the engine torque and produce better performance than the previous strategies without the engine map, especially in the high speed region.

• Journal of Mechanical Science and Technology
• /
• 제16권9호
• /
• pp.1166-1174
• /
• 2002

This paper presents the implementation and vehicle tests of a vehicle longitudinal control scheme for Stop and Go cruise control. The control scheme consists of a vehicle-to-vehicle distance control algorithm and throttle/brake control algorithm for acceleration tracking. The desired acceleration of a vehicle for vehicle-to-vehicle distance control has been designed using Linear Quadratic optimal control theory. Performance of the control algorithm has been investigated via vehicle tests. A millimeter wave radar sensor has been used for distance measurement. A stepper motor and an electronic vacuum booster have been used for throttle/brake actuators, respectively. It has been shown that the proposed control algorithm can provide satisfactory performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제34권10호
• /
• pp.1359-1366
• /
• 2010

Recently, many electronic control techniques for vehicles have been developed and applied. One of the technologies can be X-by-wire such as throttle-by-wire, brake-by-wire, steer-by-wire, and etc, in which most of mechanical parts are replaced into electrical wire and actuators. In this study, the effect of throttle-by-wire and brake-by-wire control systems on vehicle velocity control, especially in a school zone, are taken into consideration. The number of accidents reported in school zones is higher than that in other places. The reason for this is that many vehicle drivers do not obey speed limit regulations. Moreover, some of the students are careless while crossing the streets. Therefore, in this study, we attempt to develop a method using throttle-by-wire and brake-by-wire control systems for automatically reducing the vehicle speed such that it will be within the speed limit. First, an engine model and a transmission system model are developed for a specific vehicle model. Second, speed reduction is carried out such that the reduction follows a pre-designed cubic spline trajectory; the trajectory is determined such that rapid deceleration, which causes discomfort to the driver and passengers, can be prevented, for which a fuzzy-PID control algorithm is applied for the trajectory following control. Finally, simulation results are presented to verify the performance of the proposed speed reduction control system.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제7권9호
• /
• pp.36-47
• /
• 1999

Three-way catalyst converter, cleaning up the exhaust gas contamination of SI engine, has the best efficiency when A/F ratio is near the stoichiometry . The feedback control using oxygen sensors in the exhaust manifold has limits caused by the system delays. So the accurate measurement of air flow rate to an engine is essential to control the fuel injection rate especially on transient condition like the rapid throttle opening and closing. To measure the rapid change of flow rates. the air flow meter for the engine requires quick response, flow reversal detection, and linearity . Tjhe proposed integration type air flow meter (IFM), composed of an ultrasonic flow meter with an integration circuit, has significantly improved the measurement accuracy of air mass inducted through the throttle body. The proposed control method estimated the air mass at the cylinder port using the measured air mass at the throttle . For the fuel dynamic model, the two constant fuel model is introduced . The control parameters from air and fuel dynamics are tuned to minimize the excursion of the air fuel ratio. As a result A/F ratio excursion can be reduced within 5% when throttle rapidly opens and closes at the various engine conditions.