• 대한치과보철학회지
• /
• 제44권4호
• /
• pp.363-373
• /
• 2006

Statement of Problem : The accuracy and dimensional stability of elastomeric impression materials have been the subject of numerous investigation. Few studies have addressed the effect of changes in time on the dimensional stability of impression materials. Purpose: The purpose of this investigation was to evaluate the effects of elastomeric impression materials and storage time on dimensional stability. Materials and methods: A total of 75 impressions were made of epoxy resin dies mimicked prepared 3-unit fixed partial denture. The dies had 1 buccolingual, 1 mesiodistal and 1 occlusogingival lines and interpreped dot. Impression materials investigated included two polyether impression materials and three polyvinylsiloxane impression material. 15 specimens were made of each impression material and poured by type IV stone over times (30 minutes, 24 hours, 72 hours) after mixing; the same examiner measured each specimen 3 times at a magnification of 3.5$\times$. All statistical tests were performed with the level of significance set at .05. Results : The results indicated that significant difference at any measuring point of stone dies of the polyether impression materials and when measurements at 30 minutes, 24 hours, and 72 hours were compared ; the length of measuring point increased significantly as time passed by. However this result is not significant clinically. Analysis also showed significant differences at any measuring point when polyvinylsiloxane and polyether impression materials were compared and significant differences clinically. Conclusion: Under the conditions of this study, the shrinkage rate of the polyvinylsiloxane and polyether impression materials significantly increased as time passed by. The polyether impression materials showed higher shrinkage significantly, while the shrinkage rate of all five materials showed a significant time-dependent increase.

• 대한치과보철학회지
• /
• 제42권1호
• /
• pp.49-57
• /
• 2004

Statement of problem : The increased awareness of esthetics in dentistry has brought the esthetic consideration in prosthetic restorations . Dental ceramics offer better esthetics for use of prosthetic restorations. Unfortunately, dental ceramic materials are not always the most suitable candidate materials since their inherently brittle nature. In recent years, basic research in ceramic science has led to the recognition or several approaches to strengthen and to enhance esthetics of ceramics. Several all ceramic systems use ceramic core and porcelain build up structures . Ceramic cores influence to strength of all ceramic crowns . So the strength of ceramic cores is important to all ceramic crowns. Purpose : The purpose of this study is to estimate the flexural strength of ceramic cores in some all ceramic systems. Material and method : A biaxial flexure test was conducted on three groups(Cergo, Empress 2, In-Ceram). Each group consisted of 30 discs of nearly identical dimension with a 0.5mm, 1.0mm, 1.5mm thickness and 12mm in diameter. The fracture load was recorded by Instron. Analysis of valiance(ANOVA) and Tukey's tests were performed using SAS statistical software. Results : 1.5mm thickness of specimens were significantly stronger than 0.5mm and 1.0mm thickness of specimens in Cergo and In-Ceram. But each sepecimen group of Empress 2 was no significantly strength by thickness. In order of In-Ceram, Empress 2 and Cergo has significantly stronger strength in the same thickness. Conclusion : In-Ceram is the strongest ceramic material in 3 materials. All the materials can be used according to the required characters.

• 디지털융복합연구
• /
• 제12권11호
• /
• pp.273-279
• /
• 2014

본 논문에서는 실내 무선 채널을 고려한 3차원 위치 추적 알고리즘을 제안하고 그 시스템을 구현하였다. 본 시스템에서는 IEEE 802.15.4a 표준이 적용된 나노트론사의 상용화 모듈을 이동과 고정 노드에 사용하였다. 이 모듈은 거리 측정의 해상도를 향상시키기 위하여 첩 주파수 확산 방식을 채용하였으며, 거리는 수신된 신호 세기(RSS) 크기와 삼변측량법을 바탕으로 계산되었다. 테스트베드는 제안된 알고리즘의 위치 추적 평가 오차를 측정하고 비교하도록 구현하였다. 제안된 방법의 실험 결과 위치 평가의 정확도는 사무실 건물 내의 무선 환경에서 1m 정도의 거리 오차 정확도를 확인할 수 있었다.

• 대한구순구개열학회지
• /
• 제8권2호
• /
• pp.53-62
• /
• 2005

Submucosal type cleft palate is a kind of cleft palate. A submucosal cleft may result in shortening of the anteroposterior dimension of the hard or soft palates or both. The increased distance along with the lack of muscle connection in the soft palate usually accounts for the lack of palatopharyngeal function in patients with submucosal cleft. Resonance disorders which is found in cleft patients show hypernasality or hyponasality. Many cases of submucosal type cleft palate patients visit our clinics due to hypernasality. In this study, resonance disorders was evaluated through nasalance test. Experimental group was composed of submucosal type cleft palate patients. The patients were treated by a so-called combined therapy, i.e., operation and speech training. To observe the changing pattern by surgery, nasalance test was carried out one time before surgery and three times after surgery. Nasometer II was used as a examination. The questionaire was filled with single vowels & diphthongs. The mean nasalance score of the child was significantly lower than that of the adult at every vowel. An early age at operation (under 10 years) was that a better functional result was achieved with patients. The mean nasalance score of /i/ was highest and that of /a/ was the lowest. The result of corrective surgery in selected cases has achieved improvement in all cases. Hypernasality has been consistently diminished. he operation.

• 응용통계연구
• /
• 제33권1호
• /
• pp.61-74
• /
• 2020

심볼릭 자료 중 하나인 구간형 자료는 모든 관측값에서 단일 값이 아닌 구간을 값으로 취하며, 관측값 내에 변동이 존재한다는 특징을 갖는다. 주성분 분석은 자료의 분산을 최대로 설명하여 자료의 차원을 축소하는 방법이므로 구간형 자료의 주성분 분석은 관측값 간의 분산 뿐만 아니라 관측값 내의 분산 역시 설명하여야 한다. 본 논문에서는 구간형 자료의 세 가지 주성분 분석법을 소개하고자 한다. 또한 기존의 분위수 방법에서 균일분포를 사용하는 것이 아니라 구간의 중심점 부근이 좀 더 많은 정보를 가지고 있는 것으로 보고 절단정규분포를 사용하는 방법을 제안하였다. 모의실험과 OECD 관련 실제 통계 자료를 통하여 각 방법의 결과를 비교해 보았다. 마지막으로 분위수 방법의 경우 화살표 표현법을 통해 주성분 산점도를 그리고 분위수들의 위치와 분포를 확인하였다.

• 한국운동역학회지
• /
• 제15권4호
• /
• pp.117-129
• /
• 2005

The purpose of this study was to characterize the impact shock wave and its attenuation, and the kinematic response of the lower extremity's joints to the impact shock during downhill running in which the lower extremity's extensor acts dominantly. For this study, fifteen subjects(mean age:$27.08{\pm}4.39$; mass:$76.30{\pm}6.60$; height:$177.25{\pm}4.11$) were required to run on the 0% grade treadmill and downhill grades of 7%, and 15% in random at speed of their preference. When the participant run, acceleration at the tibia and the sacrum and kinematic data of the lower extremity were collected for 20s so as to provide at least 5 strides for analysis at each grade. Peak impact accelerations were used to calculate shock attenuation between the tibia and sacrum in time domain at each grade. Fast Fourier transformation(FFT) and power spectral density(PSD) techniques were used to analyze impact shock factors and its attenuation in the frequency domain. Joint coordinate system technique was used to compute angular displacement of the ankle and knee joint in three dimension. The conclusions were drawn as fellows: 1. Peak impact accelerations of the tibia and sacrum in downhill run were greater than that of 0% grade run, but no significant between conditions. Peak shock of PSD resembled also in pattern of peak impact acceleration. The wave of impact shock attenuation between the tibia and sacrum decreased with increasing grade, but didn't find a significant difference between grade conditions. 2. Adduction/abduction, flexion/extention, and internal/external rotation of the ankle and knee joints at support phase between grade conditions didn't make much difference. 3. At grade of 7% and 15%, there were relationship between the knee of the flexion/extension movement and peak impact acceleration during heel strike and found also it in the ankle of plantar/dorsiflexion at grade of 15%.

• Journal of the Korean Wood Science and Technology
• /
• 제37권3호
• /
• pp.177-183
• /
• 2009

경상북도 청도군에 있는 4곳의 고택을 답사하고 기둥의 특징을 분석함과 아울러 기둥 부재 시료를 대상으로 광학현미경 기법을 사용하여 수종 식별을 실시하였다. 기둥은 직경(또는 한 변의 길이)과 배치 간격, 높이 등이 서로 관련성을 갖는데 기둥 사이의 간격에 따라 보통 기둥의 직경과 기둥의 길이를 기본단위로 하여 축조됨을 알 수 있었다. 수종 식별 결과 3곳의 고택에서는 침엽수 목재가, 1곳의 고택에서는 활엽수 목재가 확인되었다. 이중 활엽수 목재는 밤나무이고 침엽수 목재는 모두 소나무인 것으로 식별되었다. 전통적으로 목구조부재로 소나무가 많이 사용되었다고는 하나 일부 활엽수재도 구조용재로 사용된 것으로 밝혀졌다.

• 대한공간정보학회지
• /
• 제1권1호
• /
• pp.159-169
• /
• 1993

GPS는 1일 24시간 고정밀(高情密) 3차원 위치해석이 가능한 위성측위 system으로서 국토개발을 위한 측지분야는 물론, 지구물리, 군사 및 Time 보정에 이르기까지 여러 분야에서 효율적인 수단으로 부각되고 있다. 그러나 GIS를 우리나라에 실제적용하기 위해서는 WGS84 타원체 상의 좌표 값을 Bessel 타원체로 변환시킬 수 있는 변환체계의 정립과 우리나라 지형에 적합한 Geoid Undulation의 model개발이 선행되어야 한다. 본 연구에서는 국내의 경도$126^{\circ}{\sim}129^{\circ}$ 위도$36^{\circ}{\sim}37^{\circ}$ 중위권 지역에 대한 Geoid Undulation을 GPS와 수준측량성과의 조합 해석(GPS/Leveling)으로 부터 다항식 Model로 도출하고 지구중력장 model(OSU91A OSU86F)에 대한 보정 다항식을 유도하여 이에 의한 geoid height을 산정, 그 특성을 고찰하였다.

• 대기
• /
• 제22권4호
• /
• pp.387-400
• /
• 2012

This study aims at examining the sensitivity of numerical simulations to the resolution of initial and boundary data, and to an application of WRF (Weather Research and Forecasting) 3DVAR (Three Dimension Variational data Assimilation). To do this, we ran the WRF model by using GDAS (Global Data Assimilation System) FNL (Final analyses) and the KLAPS (Korea Local Analysis and Prediction System) analyses as the WRF's initial and boundary data, and by using an initial field made by assimilating the radar data to the KLAPS analyses. For the sensitivity experiment, we selected a heavy rainfall case of 21 September 2010, where there was localized torrential rain, which was recorded as 259.5 mm precipitation in a day at Seoul. The result of the simulation using the FNL as initial and boundary data (FNL exp) showed that the localized heavy rainfall area was not accurately simulated and that the simulated amount of precipitation was about 4% of the observed accumulated precipitation. That of the simulation using KLAPS analyses as initial and boundary data (KLAPC exp) showed that the localized heavy rainfall area was simulated on the northern area of Seoul-Gyeonggi area, which renders rather difference in location, and that the simulated amount was underestimated as about 6.4% of the precipitation. Finally, that of the simulation using an initial field made by assimilating the radar data to the KLAPS using 3DVAR system (KLAP3D exp) showed that the localized heavy rainfall area was located properly on Seoul-Gyeonggi area, but still the amount itself was underestimated as about 29% of the precipitation. Even though KLAP3D exp still showed an underestimation in the precipitation, it showed the best result among them. Even if it is difficult to generalize the effect of data assimilation by one case, this study showed that the radar data assimilation can somewhat improve the accuracy of the simulated precipitation.

• 한국압력기기공학회 논문집
• /
• 제6권2호
• /
• pp.34-41
• /
• 2010

This work is concerned with the analysis of stress corrosion cracking(SCC) behavior of Alloy 600 nozzle penetration mock-up according to a residual stress induced by a dissimilar metal welding(DMW) in a nuclear reactor pressure vessel. The effects of the dimension and materials of the nozzle penetration on the deformation and the residual stress induced by DMW were investigated using a finite element analysis(FEA). The inner diameter(ID) change of the nozzle by DMW and its dependance on the design variables, calculated by FEA, were well consistent with those measured from the mock-up. Accelerated SCC tests were performed for three mock-ups with different wall thicknesses in a highly acidic solution to investigate mainly the effect of the residual stress on the SCC behavior of Alloy 600 nozzle. From a destructive examination of the mock-up after the tests, the SCC behavior of the nozzle was fairly related with the residual stress induced by DMW : axial cracks were found in the ID surface of the nozzle within the J-weld region where the highest tensile hoop stress was predicted by FEA, while circumferential cracks were observed beyond both J-weld root and toe where the highest tensile axial stress was expected.