• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.168-171
• /
• 2005

Thickness optimization of heavily doped p-type seeding layer was studied to improve performance of thin film silicon solar cell. We used liquid phase epitaxy (LPE) to grow active layer of $25{\MU}m$ thickness on p+ seeding layer. The cells with p+ seeding layer of $10{\mu}m\;to\;50{\mu}m$ thickness were fabricated. The highest efficiency of a cell is $12.95\%$, with Voc=633mV, $Jsc=26.5mA/cm^2,\;FF=77.15\%$. The $P^+$ seeding layer of the cell is $20{\mu}m$, thick. As thicker seeding layer than $20{\mu}m$, the performance of the cell was degraded. The results demonstrate that the part of the recombination current is due to the heavily doped seeding layer. Thickness of heavily doped p-type seeding layer was optimized to $20{\mu}m$. The performance of solar cell is expected to improve with the incorporation of light trapping as texturing and AR coating.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.14-19
• /
• 2013

The size and distribution of residual stresses and the effect of the minimum mesh size were investigated by the a-Si thin film solar cell. Attributed to the difference in coefficient of thermal expansion of the a-Si and Ag concentrated residual stresses at the joint interface of dissimilar materials. The ${\sigma}y$ and ${\tau}xy$ didn't appear in the central part, but ${\sigma}x$ existed. However, ${\sigma}x$, ${\sigma}y$ and ${\tau}xy$ appeared in the edge part and concentrated residual stresses at the interface between a-Si and Ag. Minimum mesh size gets smaller, the concentration of ${\sigma}y$ was significantly and existence area was reduced. As a result, the failure of thin film solar cells during the cutting process can be explained by the residual stresses.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.11a
• /
• pp.4.1-4.1
• /
• 2008

• Electrical & Electronic Materials
• /
• v.7 no.6
• /
• pp.481-489
• /
• 1994

The $SnO_2$/(n)Si solar cell was fabricated by electron beam evaporation method, and their properties were investigated. In proportion to increase of substrate and annealing temperature, the conductivity of $SnO_2$ thin film was increased, but its optical transmission decreases because of increasing optical absorption of free electrons in the thin film. $SnO_2$/Si Solar cell characteristics were improved by annealing, but the solar cells was deteriorated by heat treatment above 500[.deg. C]. The optimal outputs of $SnO_2$/Si solar cell through above investigations were $V_{\var}$:350[mV], $J_{sc}$ ;16.53[mA/c $m^{2}$], FF;0.41, .eta.=4.74[%]

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.54-62
• /
• 2007

In this paper, we report the research highlight on the preparation and characterization of Indium-free $Cu_2ZnSnSe_4$ and Indium-reduced $CulnZnSe_2$ thin films in order to seek the viability of these absorber materials to be applied in thin film solar cells. The films of $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ were prepared using mixed binary chalcogenides powders. It was observed that Cu concentration was a function of substrate temperature as well as CuSe mole ratio in the target. Under an optimized condition, $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ thin films grew with strong [112]. [220/204] and [312/116] reflections. Both $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ films were found to exhibit a high absorption coefficient of $104^4cm^{-1}\;Cu_2ZnSnSe_4$ film showed a band gap of 1.5eV which closes to the optimum band gap of an ideal solar absorber for a solar cell. On the other side, an increase of optical band gap from 1.0 to 1.25eV was found to be proportional with an increase of Zn concentration in the $CulnZnSe_2$ film. All films in this study revealed a p-type semiconductor characteristic.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.10
• /
• pp.1702-1705
• /
• 2016

We propose a novel hydrogen-reduced p-type amorphous silicon oxide buffer layer between $TiO_2$ antireflection layer and p-type silicon window layer of silicon thin film solar cells. This new buffer layer can protect underlying the $TiO_2$ by suppressing hydrogen plasma, which could be made by excluding $H_2$ gas introduction during plasma deposition. Amorphous silicon oxide thin film solar cells with employing the new buffer layer exhibited better conversion efficiency (8.10 %) compared with the standard cell (7.88 %) without the buffer layer. This new buffer layer can be processed in the same p-chamber with in-situ mode before depositing main p-type amorphous silicon oxide window layer. Comparing with state-of-the-art buffer layer of AZO/p-nc-SiOx:H, our new buffer layer can be processed with cost-effective, much simple process based on similar device performances.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.153-155
• /
• 2009

In this study, we fabricated the $Cu(In,Ga)Se_2$ (CIGS) thin-film solar cells by using a polyimide substrate. The CIGS thin-film was deposited on Mo coated polyimide substrate by a 3-stage co-evaporation technique. Because the polyimide shows thermal transformation at about $400^{\circ}C$, the substrate temperature of co-evaporation process was set to below $400^{\circ}C$. Corresponding solar cell showed a conversion efficiency of 7.08 % with $V_{OC}$ of 0.58 V, $J_{SC}$ of 24.99 $mA/cm^2$ and FF of 0.49.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1564-1567
• /
• 2009

Cu(In,Ga)$Se_2$ (CIGS) thin films were formed using CIGS bulk by electron-beam evaporation method with an evaporation current from 20 mA to 90 mA. The experimental results showed that the chemical compositions and the properties of CIGS films varied with the different evaporation current. The Cu-rich CIGS film was deposited successfully with a band gap of 1.20 eV when the evaporation current was 90 mA.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.394-396
• /
• 2012

Chemical bath deposition (CBD) process conditions for depositing CdS buffer layers was studied for high efficiencies of CIGS thin film solar cells. Growth rate of CdS thin films has an effect on surface morphology and quality of thin films. By the change of growth rate, CdS buffer layers showed a large difference in surface morphology and this difference was closely related with the photovoltaic properties of CIGS solar cells.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.766-772
• /
• 2011

Amorphous Si (a-Si) thin films of $p^+/p^-/n^+$ were deposited on $Si_3N_4$/glass substrate by using a plasma enhanced chemical vapor deposition (PECVD) method. These films were annealed at various temperatures and for various times by using a rapid thermal process (RTP) equipment. This step was added before the main thermal treatment to make the nuclei in the a-Si thin film for reducing the process time of the crystallization. The main heat treatment for the crystallization was performed at the same condition of $600^{\circ}C$/18 h in conventional furnace. The open-circuit voltages ($V_{oc}$) were remained about 450 mV up to the nucleation condition of 16min in the nucleation RTP temperature of $680^{\circ}C$. It meat that the process time for the crystallization step could be reduced by adding the nucleation step without decreasing the electrical property of the thin film Si for the solar cell application.