• Vacuum Magazine
• /
• v.3 no.1
• /
• pp.9-15
• /
• 2016

Molybdenum disulfide ($MoS_2$), which has 0.65 nm-thick atomic layer, can be easily separated layer by layer due to weak van der Waals interactions in out-of-plane direction. ($MoS_2$), has a good potential in nanoelectronics, because it has high electrical mobility and On/Off ratio. Its band gap energy changes from indirect to direct band gap energy as it goes from bulk to monolayer. Therefore, atomically thin ($MoS_2$), is widely studied in academic and engineering fields. Here, we introduce the research of atomically thin $MoS_2$ and discuss the research directions.

• Journal of the Korean Institute of Navigation
• /
• v.19 no.4
• /
• pp.83-92
• /
• 1995

In this study, a vertical type LPE system has been developed for III-V semiconductor compounds single crystal growth. On the basis of the experience & basic study using this system, the system modification has been carried out for a ultra thin multi-layer single crystal. The temperature fluctuation was within ${\pm}0.006^{\circ}C$ at $800^{\circ}C$, temperature uniformity for graphite boat around was within ${\pm}0.15^{\circ}C$ at $650^{\circ}C$, and cooling rate was controllable from $2.2^{\circ}C$/min to $0.05^{\circ}C$/min. As a result it is considered to satisfy the condition to grow a ultra thin layer single crystal of III-V semiconductor compounds.

• Korean Journal of Materials Research
• /
• v.12 no.8
• /
• pp.676-681
• /
• 2002

Microstructure, mechanical properties, and oxidation resistance of TiAIN thin films deposited on quenched and tempered STD61 tool steel by arc ion plating were studied using XRD, XPS and micro-balance. The TiAIN film was grown with the (200) orientation. The grain size of TiAIN thin film decreased with increasing Al contents, while chemical binding energy increased with Al contents. When hard coating films were oxidized at $850^{\circ}C$ in air, oxidation resistance of both TiN and TiCN films became relatively lower since the surface of films formed non-protective film such as $TiO_2$. However, oxidation resistance of TiAIN film was excellent because its surface formed protective layer such as $_A12$$O_3$ and $_Al2$$Ti_{7}$$O_{15}$, which suppressed oxygen intrusion.

• Electrical & Electronic Materials
• /
• v.7 no.2
• /
• pp.94-99
• /
• 1994

The purpose of this work is to investigate the interface characteristics of hydrogenated amorphous silicon thin films prepared by PECVD and photo-induced CVD and to examine the annealing effects of ultraviolet irradiation on hydrogenated amorphous silicon thin films which were degraded by visible light illumination. The interface layer thickness of films deposited by photo-induced CVD was about 600-900.angs. while that by PECVD was about 1000-1300.angs.. These results can show that the quality of interface layer in photo induced CVD film is better than that in PECVD sample. The electrical properties are improved by ultraviolet irradiation on visible light soaked a-Si:H films using photo-CVD light sources, probably due to the fact that UV generates phonons in a-Si:H films and anneal the meta stable defects.

• Journal of the Korean Ceramic Society
• /
• v.47 no.4
• /
• pp.353-356
• /
• 2010

Zinc oxide (ZnO) thin films were deposited using atomic layer deposition. The electrical and optical properties were characterized using Hall measurements, spectroscopic ellipsometry and UV-visible spectrophotometry. The electronic concentration and the mobility were found to be critically dependent on the deposition temperature, exhibiting increased resistivity and reduced electronic mobility at low temperature. The corresponding optical properties were measured as a function of photon energy ranging from 1.5 to 5.0 eV. The simulated extinction coefficients allowed the determination of optical band gaps, i.e., ranging from 3.36 to 3.41 eV. The electronic carrier concentration appears to be related to the reduction in the corresponding band gap in ZnO thin films.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.296-298
• /
• 1997

The performance of thin film pressure sensors with polyimide and silicon oxide as a insulating layer between the stainless steel diaphragm and the Cu-Ni strain gauges is presented. The polyimide was spun on the stainless steel diaphragm and cured in an oven. The silicon oxide was deposited by rf sputtering. The thin film pressure sensor with silicon oxide as a insulating layer showed a better nonlinearity and a lower hysteresis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.5
• /
• pp.347-350
• /
• 2013

By inserting a very thin metal layer of Ag between two outer oxide layers of amorphous silicon indium zinc oxide (SIZO), we fabricated a highly transparent SIZO/Ag/SIZO multilayer on a glass substrate. In order to find the optimized thickness of Ag layers, we investigated the variation of optical properties depending on Ag thickness. It was found that the transition of Ag layer from island formation to a continuous film occurred at a critical thickness. Continuity of the Ag film is very important for optical properties in SIZO/Ag/SIZO multilayer. With about 15 nm thick Ag layer, the multilayer showed a high optical transmittance of 80% at 550 nm and low emissivity in IR.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1281-1282
• /
• 2008

Low cost TCO(Transparent Conductive oxide) thin films were prepared by 3" DC/RF magnetron sputtering systems. For the AZO preparation processes a 99.99% AZO target (Zn: 98 wt.%, $Al_2O_3$: 2 wt.%) was used. In order to verify feasibility of the AZO thin films to organic light emitting device (OLED) application, test organic light emitting device was fabricated based on AZO as TCO, TPD as hole transporting layer (HTL), Alq3 as both emitting layer (EML) and electron transporting layer (ETL), and aluminium as cathode, where the both ITO and AZO surfaces were treated using $O_2$ RF plasma. The I-V characteristics of the AZO/TPD/Alq3/Al OLEDs were evaluated. As the results, the performance of the OLEDs with AZO as transparent conducting anode could be useable.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.7
• /
• pp.899-904
• /
• 1998

Surface motion of a magnetic fluid is studied by a linear stability analysis. When a thin horizontal magnetic-fluid layer is placed on a nonmagnetic substrate, with a vertical magnetic field applied, the surface of the ferrofluid layer can be severely corrugated, due to the normal-field instability. Based on conservation laws, it is shown that the normal-field instability of thin ferrofluid layers is a long-wave instability and that it is analogous to the interfacial mode of the thermocapillary instability in a thin horizontal layer heated from below.

• The Journal of Korean Medicine
• /
• v.23 no.2
• /
• pp.57-69
• /
• 2002

Objective: The aim of this study is to investigate the effect of Injin butanol fractions with Thin Layer Chromatography on Fas-mediated Apoptosis. Method: Injin-butanol fraction separated by TLC. MIT assay, cell cycle analysis, Caspase-3 protease assay, DNA fragmentation assay and quantitative RT-PCR were performed to evaluate the effects of TLC extraction of lnjin-butanol fraction on cell viability, cell cycle progression and apoptosis. Results: Scopoletin, luteolin, apigenin and unknown powder was isolated by TLC. Fas-mediated apoptosis analysis shows that scopoletin has inhibiting function on apoptosis. Caspase- 3 protease assay analysis shows that scopoletin inhibits activity of caspase-3. Quantitative RT-PCR analysis shows that no activity on caspase-3, but apoptosis inhibition cytokine -Bcl-2- is activated, and apoptosis activating cytokine -Bax- is unactivated. Conclusion: These results show that each fraction of Injin-butanol TLC extraction, especially scopoletin, acts as a protective function on liver cell viability, and inhibitory function on apoptosis. (J Korean Oriental Moo 2002;23(2):57-69)